Geeetech E180 Operation & User’s Manual
|
Geeetech E180, 10 4.2 Control Click the [Control] menu to enter the corresponding interface, where it is convenient to manually control the 3D printer by means of the following functions: home, move, fan, leveling, heating and speed, as shown by the picture below. 4.2.1 Home 1) When the printer is running with a TF card or connected with a computer, clicking on the [Home] menu is disabled. This situation also applies to the [Disable] status of the stepper motors.
Geeetech E180, 17 4.3.1 Wi-Fi Connectivity This sub-interface shows the Wi-Fi switch, SSID, IP address, the IP of the server and the button for autonomous Wi-Fi connectivity upon starting the printer [Connect Autonomously]. Switch on the Wi-Fi button and click the [Set] to visit the interface for Wi-Fi configuration, as shown by the picture below.
Geeetech E180, 4 Safety and Compliance FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to p
6 1. About E180 Geeetech has launched its brand new cloud 3D printer --- E180, trying its hand at integrating 3D printing technology into education. Compact and easy-to-manage, E180 is geared toward helping students map their boundless imagination to real experiences and tangible creations through trial and error. Made from sheet metal and inj
9 2. Software Resources We use EasyPrint 3D as the printing and control software by default. Please click on here to download. After your downloading, it is convenient to install this software by following the guidance. 3. USB Driver Connect the printer to your computer (Windows 7) with USB cable, the motherboard driver installer will au
22 to leveling point 1 and make the build platform raise up to reduce the distance between the nozzle and the build platform. If you can feel a big amount of friction, it means the distance between the nozzle and build platform is too close. The filament can’t be extruded out or can even be jammed. You need to clockwise rotate the nut in the bottom
Geeetech E180, 38 ⑥ Choose one of the available Wi-Fi hotspots. Click [Next], and, if the Wi-Fi needs the password, the interface will show the Wi-Fi password input box. Just input the correct password, and then click “[OK]”, as shown in the picture below.
Geeetech E180, 13 4.2.3 Fan On this interface you can observe and modify the status of the fans for the extruder and the control board. 1) The two fan switches are closed by default, when you start the printer. It will autonomously open upon printing. During the printing process, it is convenient to switch on or off the fans by clicking the buttons. When the switches are on, you can adjust the speed of the fans; When the switches are off, the speed of the fans can’t be modified.
Geeetech E180, 28 2) Click the [Save] button to save the .Gcode file in TF card, as shown in the picture below. Note: The .Gcode file shall be kept in the root file of TF card, or the printer can’t recognize the file.
Geeetech E180, 43 9. Contact us Technical support 1. There are lots of documents and troubleshooting for MeCreator 2 on our website. They are good resources if you would like to quickly solve problems by yourself. 2.If you still can not solve problems yourself even with the help of above files, you can send e-mail to [email protected],we will reply to you within 24 hours. Sales For more products of Geeetech, please visit www.geeetech.com or send e-mail to [email protected] Feedback In order to improve our products to provide better user experience, please send your comments and suggestions to Rita.xia
Geeetech E180, 19 4.3.3 Calibrating the Touch Screen The touch screen may have errors in terms of its displaying effects, for the reason of long-time usage. But no worries! It is effective to calibrate the screen via the calibration function. Click to enter the [screen calibration] mode. Click the “+” on the screen, according to the prompts. If the calibration is successful, a prompt box will pop up, as shown by the picture below. Choose [Yes] to recalibrate the screen. Choose [No] to return to the [settings] screen. 4.3.4 About Choose [About] to visit the [Info] interface, where you could chec
Geeetech E180, 5 Safety alert symbols precede each safety message in this manual. These symbols indicate potential safety hazards that could harm you or others or cause product or property damage. Warning: The Geeetech E180 generates high temperatures. Always allow the Geeetech E180 to cool down before you reach inside. Warning: The Geeetech E180 includes moving parts that can cause injury. Never reach inside the Geeetech E180 while it is in operation. Warning: There is a risk of shock. This product is not user serviceable. Warning: Do not leave the Geeetech E180 unattended during operation. Caution: Do no
Geeetech E180, 24 4. Click the [connect] button on the top right to connect E180 with your computer. At this time, you could observe the real-time status of the E180 on the bottom of EasyPrint 3D. Now we’ve completed the preparatory job before printing. In the next part, we will load and slice a 3D model and begin to print. 6.2 Slice and Print The file format of the model file for 3D printer is usually .stl. E180 supports the following file format: STL, G-code. You can download models on the internet for printing. Of course you can also design some creative models by yourselves. Here we print a small dragon. 1) First, st
Geeetech E180, 21 Step 2.Click the leveling point 1, the extruder will move to the first point. Put a piece of A4 paper between the nozzle and build platform. Slide the paper back and forth. Stop when you feel the nozzle just start to grab a little bit. If you cannot feel a little bit friction at all, it means the distance between the nozzle and build platform is too far and the adhesion of filament to the platform will be not guaranteed. You need to anticlockwise rotate the nut in the bottom of the platform whic
Geeetech E180, 15 a. Choose 1: raise the printing head to Z=10mm and move it to point 1. At the same time, lower the printing head to Z=0mm. The icon will turn into . b. Choose 2: raise the printing head to Z=10mm and move it to point 2. At the same time, lower the printing head to Z=0mm. The icon will turn into . c. Choose 3: raise the printing head to Z=10mm and move it to point 3. At the same time, lower the printing head to Z=0mm. The icon will turn into . d. Choose 4: raise the printing head to Z=10mm and move it to point 4. At the same time, lower the printing head to Z=0mm. The icon will turn into . e. Choose 5: raise the printing head to Z=10mm and move it
Geeetech E180, 41 Go back to App, click “[OK]”to enter the home page. The status on the homepage displays that the printer is on-line. Till here, the configuration between App and the printer is finished. Now you can print and control the printing via App. ⑧. If you choose a Wi-Fi hotspot without password, click “Next” and continue your setting from step ⑦. 8. Specifications of E180 Printing parameters Print technology: FDM Build volume: 180x130x130mm Printing precision:0.05mm Positioning precision: X/Y:0.11mm. Z: 0.0025mm Print
Geeetech E180, 23 the build platform may be affected. You need readjust the leveling. iii. When there is the wrapping, curling or after you dismount the extruder, please readjust the leveling. After restoring factory settings, we suggest you check the height of the nozzle and platform. 6. Start to Print 6.1 Connect E180 Connect E180 with your computer with a USB cable. Turn on the power switch. 1. Start EasyPrint 3D (your first time to use EasyPrint 3D). 2. Click the [printer] menu on the top left to choose the corresponding COM port. Th
Geeetech E180, 36 ④.Click [Next] to start to detect Wi-Fi built in the printer. If not detected, it will pop up a prompt “Printer Wi-Fi is not detected”. Click [OK] and again click [Next] to redetect. If the Wi-Fi is detected, you could see the following picture.
Geeetech E180, 42 Control software: EasyPrint 3D File format: .stl, G-code Temperature: Max heated bed temp: About 110 °C Max extruder temp: About 240°C Electrical: Power supply: Input: 110V-220V Output:DC24V/15A 360W Connectivity: Wi-Fi, USB, TF card (support stand-alone printing) Display screen:3.2 Full color touch screen Mechanical: Chassis: Metal plate + injection molding (a portable cantilever type 3D printer) Build Platform: Aluminum alloy plate XYZ Rods: Wear-resistant, stainless steel and lead screw (Z axis) Stepper Motors: 1.8°step angle with 1/16 micro-stepping Physical Dimensions & Weight Machine Dimension: 284x130x3
Geeetech E180, 40 Then the interface returns back to the control panel of the printer. You can see the prompt, as shown in the picture below. Click the button“Connect”on control panel, the interface will skip to Wi-Fi interface to connect with Network. The icon and status bar of Wi-Fi become blue on Wi-Fi interface. Meanwhile, SSID, IP Address and Server on this interface will display the relevant information, as shown in the picture below.
25 2) Print settings: click the [print settings] menu and modify the relevant parameters. Here we take the [Quick] mode as an example. Choose the [Quick] mode, set the printing quality as [Standard] and take the parameters like [Infill], [Extruder temperature] and [Layer height] by default. Select the [Support] button, according to your printing need. Finally, click
Geeetech E180, 3 product misuse or abuse, product modification, improper product selection, noncompliance with any codes, or misappropriation. To the fullest extent permissible by the applicable law, we hereby disclaim any and all responsibility, risk, liability, and damages arising out of death or personal injury resulting from assembly or operation of our products. Geeetech assumes no responsibility, nor will be liable, for any damages to, or any viruses or malware that may infect your computer, telecommunication equipment, or other property
Geeetech E180, 2 Terms Please be advised of the following terms (the “Terms”) regarding this User Manual (this “Manual”): All information in this Manual is subject to change at any time without notice and is provided for convenience purposes only. Geeetech reserves the right to modify or revise this Manual in its sole discretion and at any time. You agree to be bound by any modifications and/or revisions. Contact the Geeetech Support Team for up-to-date information. Content Copyright. The design of this Manual
34 ②.Turn on Wi-Fi and click the button “Set “to enter the Config mode, as shown in the picture below. ③.Choose Wi-Fi at the control panel on APP. At the page of pop-up, click the button “Wi-Fi” to enter Wi-Fi configuration, as shown in the picture below.
DOWNLOAD |
Geeetech Duplicator 5 3D Printers Assembly manual
Duplicator 5 |
Geeetech Prusa I3 A pro 3D Printers Assembly instructions manual
Prusa I3 A pro |
Geeetech GiantArm D200 3D Printers Operation & user’s manual
GiantArm D200 |
Geeetech A30 3D Printers Operation & user’s manual
A30 |
Geeetech Acrylic I3 Pro 3D Printers Operation & user’s manual
Acrylic I3 Pro |
Geeetech Prusa M201 3D Printers Quick starter manual
Prusa M201 |
Geeetech Rostock 301 3D Printers Operation & user’s manual
Rostock 301 |
Geeetech A20M 3D Printers Operation & user’s manual
A20M |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Singer | Sewing Machine | Manual | singer/sewing-machine-A2R.pdf | 27 Jul 2023 | 6 | |
2 | Volvo | XC60 Drive | Owner's manual | volvo/xc60-drive-V7W.pdf | 04 Jun 2023 | 290 | 8.13 Mb |
3 | DNP | CX-320 | Instruction manual | dnp/cx-320-UG2.pdf | 03 Jul 2022 | 52 | |
4 | Philips | 47PFL3603D | Quick start | philips/47pfl3603d-H7D.pdf | 21 Aug 2023 | 1 | 1.54 Mb |
5 | Canon | imageRUNNER 3300 | Function manual | canon/imagerunner-3300-3I2.pdf | 20 Mar 2023 | 156 | |
6 | American Standard | Savona Elite Corner Whirlpool 2902E | Installation instructions | american-standard/savona-elite-corner-whirlpool-2902e-UX4.pdf | 06 May 2023 | 4 |
MUTOH
VJ-628Operations and Maintenance MethodsOperation Manual• Unauthorized copying or duplication of the whole or part of the contents of this manual is prohibited.• Every care has been taken in writing the contents of this manual, but please contact MUTOH or the dealer you purchased the product from if you find any unclear, erroneous or otherwise unsatisfac …
VJ-628 ValueJet(80 pages) |
XYZ Printing
Unpacking Product Overview & AccessoriesNobel 1.0A is shipped with the following parts and accessories. After unpacking, please inspect the interior and exterior of the printer and accessories for damage. Please contact support for any missing or defective parts and accessories.④Select “UTILITIES” > “MOVE PLATFORM”>“TO TOP”>“YES� …
Nobel 1.0A(2 pages) |
Ultimaker
Installing the Extrusion Upgrade kitThe Extrusion Upgrade kit allows you to turn your Ultimaker 2 or Ultimaker 2 Extended into an Ultimaker 2+ or Ultimaker 2 Extended+. This guide shows how to install the upgrade kit step by step. In addition to reading our detailed support text guide there are an installation guide video and installation manual available. Y …
EXTRUSION UPGRADE(12 pages) |
Prusa Research
Raspberry PI Chassis Mount forPrusa I3 MK3S Printer !� …
i3 MK3S Multi Material Upgrade 2S(34 pages) |
STACKER
STACKER S4 and STACKER S2USER GUIDE – PART II©Copyright 2017 STACKER, LLCMinneapolis, MN 55427http://stacker3d.comSTACKER® is the registered trademark of STACKER, LLC.Revised: 7 August 2017
…
S4(47 pages) |
Deezmaker
!"##"#$%%&'()%#%*+%!,%%%!"#$%&'()&*%%#+,-.&('&*&/012"(3&/#"*&4#)%2(5&6378&9#,)0*).&::8&;7:6&!"#$%&'(&)'*+%*+,&%<*,-#&('&=(5"#5"%&3333333333333333333333333333333333333333333333333333333333333333333333333333333333 …
Bukito(26 pages) |
Wood master Furnace FORCE 30Furnace #86O9VX FORCE 30, 44 |
Bogen Music Mixer PM-3000PM-3000 (Music Mixer ePDF User Guide, #875JO4) PM-3000, 2 |
Barco Projector OV-1008Barco Projector OV-1008 Specifications OV-1008, 4 |
RCA Software RTB1013PDF Manual (@3J576X), RCA RTB1013 Software (20th Dec 2023) RTB1013, 2 |
clage Water Heater FWX SOLARTRONICFWX SOLARTRONIC Operating instructions for the user - XNL461 FWX SOLARTRONIC, 16 |
Poulan Pro Tiller PRRT50Poulan Pro Tiller Operator's manual (File: poulan-pro-prrt50-tiller-22, 13th Dec 2023) PRRT50, 22 |
Samsung Laptop NP350E7CPDF User Manual (@EZP482), Samsung NP350E7C Laptop (Saturday 14-10-2023) NP350E7C, 149 |
C3IT Monitor CT7000#VLTOQ5 CT7000: C3IT Monitor Owner Documentation CT7000, 17 |
Philips Home Cinema speakers CSS9211/12CSS9211/12 Operation & user’s manual - SP97EB CSS9211/12, 17 |
Hand Held Products Security Camera 4600gHand Held Products Security Camera Quick start manual (File: hand-held-products-4600g-quick-start-manual-20, Mon 12.2023) 4600g, 20 |
Nokia Network Card D311Guide: Nokia D311 (X6T684, Upd.22/12/2023) D311, 68 |
Black & Decker Hair Clipper SZ360PDF Manual (@58F9TI), Black & Decker SZ360 Hair Clipper (30.01.2024) SZ360, 20 |