Siemens SIMATIC NET CP 343-1 Product Information

Text of Siemens SIMATIC NET CP 343-1 User Guide:

• Siemens SIMATIC NET CP 343-1, SIMATIC NET Produktinformation Product Information Information produit Informazioni sul prodotto Información sobre producto Stand/ Dated/ Edition/ Versione/ Versiòn 06/99 CP 343–1 6GK7 343-1BA00-0XE0 ab Ausgabestand 7 (FW–Stand V5.00) version 7 or higher (firmware V5.00) à partir de la version 7 (microprogramme V5.00) a partire dalla versione 7 (versione FW V4.00) a partir de la versión 7 (FW-V5.00) SIMATIC S7–300 Deutsch / English / Français / Italiano / Español E SIEMENS AG 1998 Änderungen vorbehalten Subject to alteration Sous réserve de modification

• Siemens SIMATIC NET CP 343-1, Hinweis / Note / Avertissement / Avvertenza / Indicación Achtung Vor der Inbetriebnahme Hinweise in der entsprechenden aktuellen Dokumentation beachten. Die Bestelldaten hierfür entnehmen Sie bitte den Katalogen oder wenden Sie sich an Ihre örtliche SIEMENSĆNiederlassung. Die Inbetriebnahme ist solange untersagt, bis festgestellt wurde, daß die Maschine, in die diese Komponente eingebaut werden soll, den Bestimmungen der Richtlinie 89/392/EWG entspricht. Attention Prior to startup you must observe the notes in the relevant

• english 1 Product information CP 343–1 C79000–Z8964–C038–05 Contents Notes for the Reader 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 The CP 343-1 Communications Processor 3. . . . . . . . . . . . . . . 1.1 Characteristics 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Performance Dat

• Siemens SIMATIC NET CP 343-1, english 2 Product information CP 343–1 C79000–Z8964–C038–05 Notes for the Reader Safety Guidelines This manual contains notices which you should observe to ensure your own personal safety, as well as to protect the product and connected equipment. These notices are highlighted in the manual by a warning triangle and are marked as follows according to the level of danger: Note draws your attention to particularly important information on the product, handling the product, or to a particular part of the documentation. ! Caution indicates that minor personal injury or property damage can result if proper pre- cautions

• english 3 Product information CP 343–1 C79000–Z8964–C038–05 1 The CP 343-1 Communications Processor Application The CP 343-1 communications processor is designed for operation in an S7-300 programmable logic controller. It allows the S7-300 to be attached to Industrial Ethernet. LED displays Mode selector AUI/ITP interface 15-pin sub D with sliding locking mechanism Figure 1 CP 34

• Siemens SIMATIC NET CP 343-1, english 4 Product information CP 343–1 C79000–Z8964–C038–05 Configuration You can configure the CP 343–1 via MPI or LAN/Industrial Ethernet. You re- quire STEP 7 with the following version of NCM S7 for Industrial Ethernet (abbreviated to ”NCM IE” below): Table 1 Version STEP7/NCM IE Functionality of the CP 343–1 V2.x to V5.x The same functionality is available as with the previous versions of the CP. S Configuration data created with these STEP 7 or NCM versions can be downloaded to the CP 343–1. V5.x + S

• Siemens SIMATIC NET CP 343-1, english 5 Product information CP 343–1 C79000–Z8964–C038–05 Note If there is a diagnostic connection to the CP via the CPU, configuration data cannot be downloaded automatically to the CP by the CPU at the same time! Extended Functions Compared with Version 5 S Reading and writing data in the FETCH/WRITE mode The services FETCH and WRITE are supported for direct access to sy- stem memory areas on the SIMATIC S7 PLC via ISO transport and and ISO-on-TCP connections. The SIMATIC S7-300 with the CP 343-1 is always the server (passive connection establishment), while the fetch or write access (client

• english 6 Product information CP 343–1 C79000–Z8964–C038–05 Table 2 CPU MLFB–Number CPU 614 6ES7 614–1AH03–0AB3 CPU 614–Z 6ES7 614–1AH03–0AB3–Z The table lists the CPUs approved at the time of printing this product informa- tion bulletin. S7–300 CPUs approved later and not listed in the table also support the range of functions described here. All v

• Siemens SIMATIC NET CP 343-1, english 7 Product information CP 343–1 C79000–Z8964–C038–05 1.2 Performance Data 1.2.1 Characteristics of S7 Communication The functions and characteristics of S7 communication are described in /8/ and /11/. 1.2.2 Characteristics of ISO Transport Connections The following information is important for operating ISO transport connections (SEND/RECEIVE interface): Table 4 Characteristic Explanation / Values Total number of connections on Industrial Ethernet 32 maximum Number of connections for S7 communication on I

• Siemens SIMATIC NET CP 343-1, english 8 Product information CP 343–1 C79000–Z8964–C038–05 Table 5 Component Explanation / Values Run time in the CPU 314-1 per block AG-SEND/AG-LSEND, AG-RECV/AG-LRECV 2.5 ms to 5 ms 1.3 Displays and Mode Selector LED Displays The LED panel on the front of the CP 343-1 has three display elements: SF STOP RUN Figure 2 LED Displays CP Operating Mode The LEDs indicate the current operating mode of the CP 343-1 as follows: STOP–LED (yellow) RUN–LED (green) SF–LED (red) CP operating mode start up RUN STOPPING STOP STOP with internal error

• Siemens SIMATIC NET CP 343-1, english 9 Product information CP 343–1 C79000–Z8964–C038–05 STOP–LED (yellow) CP operating modeSF–LED (red) RUN–LED (green) Module fault / system error Legend: lit off flashing Note Read the explanations of the operating modes in the NCM S7 for Industrial Ethernet manual /8/. Controlling the Operating Mode There are three ways in which you can control the mode of the CP 343-1, as follows: S Mode selector S From a PG/PC. You can also control the modes using the configuration software in STEP 7, as follows . – NCM S7, Diagnostics for Industrial Ethernet (see /8/);

• Siemens SIMATIC NET CP 343-1, english 10 Product information CP 343–1 C79000–Z8964–C038–05 Note Read the sections about downloading configuration data to the CP in the NCM S7 for Industrial Ethernet manual /8/. 1.4 Further Information on Operation Downloading Firmware The CP 343-1 supports firmware updates using the Firmware Loader. An update of the firmware can be downloaded from the PC/programming de- vice at any time. After downloading the firmware, the CPU must be reconfigu- red (power off/on or memory reset). For more information on downloading the firmware, refer to the README file of the NCM S7 for Industrial Ethernet configuration software. Note Read the informati

• english 11 Product information CP 343–1 C79000–Z8964–C038–05 Status on the FC call interface; special situation with FC versions With the FCs AG_SEND (FC 5) and AG_RECV (FC 6), you receive the follo- wing return values after a connection is aborted: S AG_SEND: DONE=1; ERROR=0; Status=0000 H S AG_RECV: DONE=0; ERROR=1; Status=8183 H The new FCs for longer data fields

• Siemens SIMATIC NET CP 343-1, english 12 Product information CP 343–1 C79000–Z8964–C038–05 2.2 Procedure Steps in Installation Installing the CP 343-1 involves the following steps. S Plug in the CP 343-1 and secure it with the screws (make sure that the bus connector between the CPU/IM and CP 343-1 is present). S Attach the CP 343-1 to Industrial Ethernet as illustrated in Section 2.3. S Connect a 24 V power supply. Note Make sure that you use the same voltage source as for the CPU or IM 361. Note The two front panels must be kept closed during operation. The module must be installed so that its upper and

• Siemens SIMATIC NET CP 343-1, english 13 Product information CP 343–1 C79000–Z8964–C038–05 2.3 Attaching the CP 343-1 to Industrial Ethernet The CP 343-1 can be attached to Industrial Ethernet using a S Transceiver with an AUI interface Transceiver cable (drop cable) 727-1 Transceiver SF RUN STOP R STOP RUN CP 343–1 Figure 3 Attaching the CP 343-1 to Industrial Ethernet with AUI/Transceiver The CP 343-1 generates and supplies the 13 V power required by the transceiver. S Industrial Twisted Pair attachment, for example using a Optical Switch

• Siemens SIMATIC NET CP 343-1, english 14 Product information CP 343–1 C79000–Z8964–C038–05 ITP installation cable SF RUN STOP R STOP RUN CP 343–1 e.g Optical Switch Modul (OSM) SF RUN STOP R STOP RUN CP 343–1 Figure 4 Attaching the CP343-1 to Industrial Ethernet with TP/Optical Switch Module (OSM) or Hub S Optical Industrial Ethernet using an AUI attachment Connection of the CP 343-1 TCP to Industrial Ethernet is also possible using an optical transceiver with an AUI interface. Star coupler Fiber optic cable 727-1 Connecting cable Optical module SF RUN STOP R STOP RUN CP 343–1 Figure 5 Attaching the CP 343-1 to Industrial Ethernet with AUI/

• Siemens SIMATIC NET CP 343-1, english 15 Product information CP 343–1 C79000–Z8964–C038–05 3 Technical Data 3.1 General Technical Data Dimensions and Weight Dimensions, module in casing H x W x D (mm) 125x80x120 Weight approx. 750 g Voltage, Current, Operating Conditions Power supply 5 V DC +/– 5% 24 V DC +/– 5% Current consumption: – from the S7-300 backplane bus: – from the external 24 V supply: 70 mA 0.6 A. Permitted ambient temperature Specifications according to /7/ must be adhered to when operating an S7-

• Siemens SIMATIC NET CP 343-1, SF RUN STOP R STOP RUN CP 343–1 english 16 Product information CP 343–1 C79000–Z8964–C038–05 3.2 Pinout Connector for Industrial Ethernet On the front panel of the CP 343-1, there is a 15-pin sub D female connector with a sliding locking mechanism for connecting a transceiver cable. The signals of an ITP interface can also be applied to this connector (switchover by relay). For operation via the AUI interface, use the 727-1 transceiver cable. A special SIMATIC NET ITP cable must be used when operating via the ITP interface. Pin– No Signal– name Function 1 MEXT External ground, shield 2 CLSN Collision + 3 TRMT / TPETXD Transmit + / TPE transmit data + 4 Grou

• Siemens SIMATIC NET CP 343-1, english 17 Product information CP 343–1 C79000–Z8964–C038–05 3.3 Notes on the CE Approval of SIMATIC NET Products Product name: CP 343-1 Order number: 6GK7 343-1BA00-0XE0 EU Directive EMC89/336/EEC The SIMATIC NET products listed above meet the requirements of the EU directive 89/336/EEC ”Electromagnetic Compatibility”. The EU conformity certificates are available for the relevant authorities accor- ding to the EU directives and are kept at the following address: Siemens Aktiengesellschaft, Bereich A&D Industrielle Kommunikation SIMATIC NET (A&D PT 2) Postfach 4848 D–90327 Nürnb

• Siemens SIMATIC NET CP 343-1, english 18 Product information CP 343–1 C79000–Z8964–C038–05 4 References The following documentation is necessary for configuration and operation and contains detailed information: For installing and starting up the CP 343-1 Manual: S7-300 Programmable Controller, Hardware and Installation For using and configuring the CP 343-1 Manual: SIMATIC NET NCM for S7 Industrial Ethernet SIMATIC NET Manual: Triaxial Networks for Industrial Ethernet Ethernet Manual (HIR) User’s Guide to STEP 7 Part of the basic STEP 7 package. SIMATIC NET Manual: ITP Networ

• Siemens SIMATIC NET CP 343-1, C79000-Z8974-C43-01 Mail / FAX Reply (Call ++911-978-3321) --- --- From Name ............................................................................. Position ............................................................................. Company ............................................................................. Address ............................................................................. Town ............................................................................. Postcode ............................................................................. C

More Instructions:

	Siemens SIMATIC NET CP 343-1 Operation & user’s manual 29-08-2022 56	DOWNLOAD
	Siemens SIMATIC NET CP 343-1 Manual  16-04-2024 58	DOWNLOAD
	Siemens SIMATIC NET CP 343-1 Manual  15-03-2024 78	DOWNLOAD

Related Products and Documents (Network Card):

Comparable Devices:

Similar Resources:

• Dell Inspiron 7500 (63 pages) Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com. Please check out our eBay auctions for more great deals on Factory Service Manuals: servicemanuals4u …

• Liebert IntelliSlot (20 pages) MonitoringFor Business-Critical Continuity™Liebert IntelliSlot® Web CardsFirmware Upgrade Manual – Liebert IntelliSlot Web Card, Liebert IntelliSlot Web Card-LB, Liebert IntelliSlot Web Card-LBDS, Liebert IntelliSlot Web/485 Card-ADPT …

• Siemens S5-155U (536 pages) RGB ELEKTRONIKA AGACIAK CIACIEKSPÓŁKA JAWNA Jana Dlugosza 2-6 Street51-162 WrocławPoland [email protected] +48 71 325 15 05www.rgbautomatyka.plwww.rgbelektronika.plDATASHEETwww.rgbautomatyka.plwww.rgbelektronika.pl OTHER SYMBOLS:6ES5242-1AA136ES52421AA13, 6ES5242 1AA13, 6ES5242-1AA13SIEMENS …

• Laird SDC-EC15N (17 pages) Americas : +1-800-492-2320 Option 2 Europe : +44-1628-858-940 Hong Kong : +852-2923-0600 www.lairdtech.com/wi-fi SDC-EC15N Hardware Integration Guide Version 2.0 …

• Wavecom WISMO Quik Q2501 (79 pages) confidential © Page : 1 / 79 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable. WISMO Quik Q25 series WISMO Quik Q2501 Customer Design G …

• HP Laserjet,Color Laserjet 4550 (52 pages) installinstallationinstallazioneinstalació ninstallationinstallationinstallatieasennusinstallereinstalaçã oinstallerainstalacjalea esto primeroq2444bHP LaserJet Information Engineering …

Comments, Questions and Opinions: