Manualios.com

HP HP 830 Series Command Reference Manual

HP HP 830 Series Manual Online:

3.8, 611 votes
HP HP 830 Series User Manual
HP HP 830 Series User Guide
HP HP 830 Series Online Manual

Text of HP HP 830 Series User Guide:

  • 105 Field Descri p tion LLDP local-information of port 1 LLDP information to be sent out of port 1. Port ID subtype Port ID type, which can be MAC address or interface name. Port ID Port ID, the value of which depends on the port ID subtype. Management address interface type Numbering type of the interface identified by the management address. Mana

  • HP HP 830 Series, 50 Views WLAN-ESS interface view, Ethernet interface view, port group view, Layer 2 aggregate interface view Default command level 2: System level Parameters access: Configures the link type of a port as access. hybrid: Configures the link type of a port as hybrid. trunk: Configures the link type of a port as trunk. This keyword is not supported in WLAN-ESS interface view. Usage guidelines To change the link type of a port from trunk to hybrid or vice versa, you must first set the link type to access. The configuration made in Ethernet or WLAN-ESS interface view applies only to the port.

  • 11 Field Descri p tion Type Link type of the interface: • A—Access. • H—Hybrid. • T—Trunk. PVID Port VLAN ID. Table 4 Causes for the physical state of an interface to be DOWN Field Descri p tion Not connected No physical connection exists (possibly because the network cable is disconnected or faulty). Administratively The port was shut

  • HP HP 830 Series, 115 Field Descri p tion DEFAULT Indicates whether a type of TLV is sent through a port by default. Basic optional TLV Basic TLVs: • Port description TLV. • System name TLV. • System description TLV. • System capabilities TLV. • Management address TLV. IEEE 802.1 extended TLV IEEE 802.1 organizationally specific TLVs: • Port VLAN ID TLV. • Port and protocol VLAN ID TLV. • VLAN name TLV. IEEE 802.3 extended TLV IEEE 802.3 organizationally specific TLVs: • MAC

  • HP HP 830 Series, Legal and notice information © Copyright 2014 Hewlett-Packard Development Company, L.P. No part of this documentation may be reproduced or transmitted in any form or by any means without prior written consent of Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

  • HP HP 830 Series, 87 Usage guidelines If you specify the verbose keyword, the detailed information of the specified fast Layer 2 forwarding entry or all fast Layer 2 forwarding entries is displayed. Examples # Display the brief information of all fast Layer 2 forwarding entries. <Sysname> display mac-fast-forwarding cache all ----------------------------------------------------------------------- Fast Forward Cache Table -----------------------------------------------------------------------

  • HP HP 830 Series, 79 link-aggregation load-sharing mode Use link-aggregation load-sharing mode to configure the global or group-specific link-aggregation load sharing mode. Use undo link-aggregation load-sharing mode to restore the default. Syntax link-aggregation load-sharing mode { destination-ip | destination-mac | source-ip | source-mac } * undo link-aggregation load-sharing mode Default The global or group-specific link-aggregation load sharing mode is source and destination MAC addresses. Views System view, Layer 2 aggregate interface view Default command level 2: System level Parameters destination-ip: Load shares traff

  • HP HP 830 Series, 70 exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. Usage guidelines If you do not specify the bridge-aggregation keyword, the command displays information about all interfaces. If you specify the bridge-aggregation keyword and do not specify an interface number, the command displays information about all aggregate interfaces. If you specify the bridge-aggregation interface-number option, the command d

  • HP HP 830 Series, 46 You cannot assign Layer 2 aggregate interfaces to a VLAN. Examples # Assign Ten-GigabitEthernet 1/0/1 through Ten-GigabitEthernet 1/0/3 to VLAN 2. <Sysname> system-view [Sysname] vlan 2 [Sysname-vlan2] port Ten-GigabitEthernet1/0/1 to Ten-GigabitEthernet1/0/3 Related commands display vlan port access vlan Use port access vlan to assign an access port to the specified VLAN. Use undo port access vlan to restore the default. Syntax port access vlan vlan-id undo port access vlan Default All access ports belong to VLAN 1. Views WLAN-ESS interface view, Ethernet interfa

  • HP HP 830 Series, 81 port link-aggregation group Use port link-aggregation group to assign an Ethernet interface to an aggregation group. Use undo port link-aggregation group to remove an Ethernet interface from the aggregation group to which it belongs. Syntax port link-aggregation group number undo port link-aggregation group Views Ethernet interface view Default command level 2: System level Parameters number: Specifies the number of an existing aggregate interface corresponding to an aggregation group. The value range varies by device model. For more informati

  • 83 Views Layer 2 aggregate interface view Default command level 2: System level Examples # Shut down Layer 2 aggregate interface Bridge-Aggregation 1. <Sysname> system-view [Sysname] interface bridge-aggregation 1 [Sysname-Bridge-Aggregation1] shutdown

  • HP HP 830 Series, 89 Field Descri p tion Cache Context Fast forwarding information. mac-fast-forwarding Use mac-fast-forwarding to enable fast Layer 2 forwarding. Use undo mac-fast-forwarding to disable fast Layer 2 forwarding. Syntax mac-fast-forwarding undo mac-fast-forwarding Default Fast Layer 2 forwarding is enabled. Views System view Default command level 2: System level Examples # Enable fast Layer 2 forwarding. <Sysname> system-view [Sysname] mac-fast-forwarding reset mac-fast-forwarding cache Use reset mac-fast-forwarding cache to clear fast Layer 2 forwarding entries. Syntax reset mac-fast-forwarding cache { all | { destination-mac mac-address | sou

  • HP HP 830 Series, 45 Untagged:1, XGE1/0/1 1 Tagged: none Untagged:1, XGE1/0/2 1 Tagged: none Untagged:1, # Display information about the trunk ports. <Sysname> display port trunk Interface PVID VLAN passing BAGG1 1 1, XGE1/0/1

  • HP HP 830 Series, 54 |: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters. Usage guidelines If mac-address mac-address is specified, but mask is not specified, only the MA

  • 55 Syntax display mac-vlan interface [ | { begin | exclude | include } regular-expression ] Views Any view Default command level 1: Monitor level Parameters |: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide. begin: Displays the first line that matches the s

  • HP HP 830 Series, 39 interface vlan-interface Use interface vlan-interface to create a VLAN interface and enter its view or enter the view of an existing VLAN interface. Use undo interface vlan-interface to remove the specified VLAN interface. Syntax interface vlan-interface vlan-interface-id undo interface vlan-interface vlan-interface-id Views System view Default command level 2: System level Parameters vlan-interface-id: Specifies a VLAN interface number in the range of 1 to 4094. Usage guidelines Create the VLAN before you create the VLAN inter

  • HP HP 830 Series, 111 Examples # Display the global LLDP statistics and the LLDP statistics of all ports. <Sysname> display lldp statistics <Sysname>display lldp statistics LLDP statistics global information: LLDP neighbor information last change time:0 days,7 hours,14 minutes,43 seconds The number of LLDP neighbor information inserted : 4 The number of LLDP neighbor information deleted : 0 The number of LLDP nei

  • HP HP 830 Series, 61 Ten-GigabitEthernet1/0/2 enable WLAN-ESS1 enable WLAN-DBSS1:2 enable Table 12 Command output Field Descri p tion Mac-address learning status of the switch Global MAC address learning status (enabled or disabled). Learning Status MAC address learning status (enabled or disabled) for an interface. display mac-address statistics Use display mac-address statistics to display the statistics of the MAC address table. Syntax display mac-address statistics [ | { begin | exclude | include } regular-expression ] Views Any view Default command level 1: Moni

  • HP HP 830 Series, 108 Table 23 Command output Field Descri p tion LLDP neighbor-information of port 1 LLDP information received through port 1. Update time Time when LLDP information about a neighboring device was last updated. Chassis type Chassis ID representation: • Chassis component. • Interface alias. • Port component. • MAC address. • Network address (ipv4). • Interface name. • Locally assigned—Indicates a locally-defined chassis type other than those listed above. Chassis ID ID that identifies the LLDP sending device, which can be a MAC address, a network address, an interface, or some other value, d

  • HP HP 830 Series, 52 [Sysname-Bridge-Aggregation1] port trunk permit vlan 2 Please wait... Done. Configuring Ten-GigabitEthernet1/0/1... Done. Configuring Ten-GigabitEthernet1/0/2... Done. The output shows that Ten-GigabitEthernet 1/0/1 and Ten-GigabitEthernet 1/0/2 are the member ports of the aggregation group corresponding to Bridge-Aggregation 1. Related commands port link-type port trunk pvid Use port trunk pvid to configure the PVID for the trunk port. Use undo port trunk pvid to restore the default. Syntax port trunk pvid vlan vlan-id undo port trunk pvid Default The PVID of a trunk port is VLAN 1. Views Ethernet interface

  • HP HP 830 Series, 44 You cannot use the undo vlan command to delete VLANs reserved for protocols, management VLANs, dynamic VLANs, and VLANs configured with QoS policies. To delete one of these VLANs, first remove the configuration from the VLAN. Examples # Create VLAN 2, and enter VLAN 2 view. <Sysname> system-view [Sysname] vlan 2 [Sysname-vlan2] # Create VLAN 4 through VLAN 100. <Sysname> system-view [Sysname] vlan 4 to 100 Please wait............. Done. Related commands display vlan Port-based VLAN configuration commands display port Use display port to display informa

  • HP HP 830 Series, 88 ----------------------------------------------------------------------- # Display the brief information of fast Layer 2 forwarding entries of source MAC address 001B-111D-B192. <Sysname> display mac-fast-forwarding cache source-mac 001B-111D-B192 ----------------------------------------------------------------------- Fast Forward Cache Table ----------------------------------------------------------------------- Number of entries in the table : 1 -----------------------------------------------------------------------

  • 91 PPPoE server commands Support for the commands in this chapter depends on the device model. For more information, see About the Command References for HP Unified Wired-WLAN Products. display pppoe-server session Use display pppoe-server session to display information about PPPoE sessions on a device operating as a PPPoE server. Syntax display pppoe-se

  • HP HP 830 Series, HP Unified Wired-WLAN Products Layer 2 Command Reference HP 830 Unified Wired-WLAN PoE+ Switch Series HP 850 Unified Wired-WLAN Appliance HP 870 Unified Wired-WLAN Appliance HP 11900/10500/7500 20G Unified Wired-WLAN Module Part number: 5998-6502 Software version: R3507P26 (HP 830 PoE+ Switch Series) R2607P26 (HP 850 Appliance) R2607P26 (HP 870 Appliance) R2507P27 (HP 11900/10500/7500 20G Module) Document version: 6W102-20140818

  • 104 Auto-negotiation supported : Yes Auto-negotiation enabled : No OperMau : speed(10000)/duplex(Full) PoE supported: No

  • HP HP 830 Series, 33 Default The description for a VLAN is VLAN vlan-id, which is the ID of the VLAN. For example, the default description of VLAN 100 is VLAN 0100. The default description for a VLAN interface is the name of the interface. For example, the default description of VLAN-interface 1 is Vlan-interface1 Interface. Views VLAN view, VLAN interface view Default command level 2: System level Parameters text: Specifies a description for a VLAN or VLAN interface. The string can include case-sensitive letters, digits, special symbols (see Table 6) , spaces, and other Unicode characters and symbols. • For a VLAN, this is a string of 1 to 32 characters. �

  • HP HP 830 Series, 12 Parameters auto: Sets the interface to operate in autonegotiation mode. full: Sets the interface to operate in full duplex mode. Usage guidelines Support for this command varies with device models. For more information, see About the Command References for HP Unified Wired-WLAN Products. Examples # Configure interface Ten-GigabitEthernet 1/0/1 to operate in autonegotiation mode. <Sysname> system-view [Sysname] interface ten-gigabitethernet 1/0/1 [Sysname-Ten-GigabitEthernet1/0/1] duplex auto flow-i

  • HP HP 830 Series, 51 Syntax port trunk permit vlan { vlan-list | all } undo port trunk permit vlan { vlan-list | all } Default A trunk port allows only packets from VLAN 1 to pass through. Views Ethernet interface view, port group view, Layer 2 aggregate interface view Default command level 2: System level Parameters vlan-list: Specifies a space-separated list of up to 10 VLAN items. Each item specifies a VLAN ID or a range of VLAN IDs in the form of vlan-id1 to vlan-id2. The value range for VLAN IDs is 1 to 4094. The value for vlan-id2 must be equal to or greater than the value for vlan-id1. Make sure

Related Products and Documents (Switch):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Craftsman 113.236400 Owner's manual craftsman/113-236400-M4G.pdf 20 Nov 2022 26 3.02 Mb
2 SEVERIN MANICURE-CENTER HG 7712 Dimensions severin/manicure-center-hg-7712-68L.pdf 20 Oct 2022 1 0.64 Mb
3 Gartner 2H06 Manual  gartner/2h06-7I8.pdf 17 Sep 2023 7 0.07 Mb
4 Lenovo ThinkCentre A62 Implementierungshandbuch lenovo/thinkcentre-a62-5I6.pdf 14 Nov 2022 46
5 Amprobe AM91RS Operation & user’s manual amprobe/am91rs-4R7.pdf 20 Feb 2023 30
6 AG Neovo X-17P Operation & user’s manual ag-neovo/x-17p-8B9.pdf 15 Apr 2023 44 1.57 Mb

Similar Resources:

  • HP

    A7340A - Surestore FC 1Gb/2Gb Switch 16B

    (120 pages)
    installation guidehp StorageWorksSAN switch 2/16version 3.1.xProduct Version: 3.1.xThird Edition (June 2003)Part Number: AA-RR84C-TEThis installation guide provides basic procedures for setting up, configuring, and managing the SAN Switch 2/16 and SAN Switch 2/16 power pak models. …
  • Audioplex

    JB-1

    (2 pages)
    Your AUDIOPLEX TECHNOLOGY JB-2 is covered by a Lifetime warranty against any defects in workmanship and materials. Any defects will be remedied without charge for labor or parts during this period of time following the date of purchase. Damage incurred by shipping or accident is not considered to be a defect, and not covered by this warranty. …
  • Accell

    UltraAV K072C-013B

    (2 pages)
    READ ME FIRST – SETUP INSTRUCTIONSThank you for purchasing the Accell UltraAV HDMI Distribution Amplifi er. This product is designed to provide an exceptional performance and value. Please review the manual before operating and retain for future reference. - CAUTION -1. Ensure the unit has suffi cient ventilation. Do not cover ventilation openings. Do …
  • Vimar

    03925

    (26 pages)
    039254-button flat device with 2.4 GHz Bluetooth® technology Low Energy standard radiofrequency transmitter, energy harvesting sup-ply powered by built-in electrodynamic generator, to complete with Eikon 20506 or 20506.2, Arké 19506 or 19506.2 or Plana 14506 or 14506.2 buttons - 2 modules.Installer ManualHOME AUTOMATION …
  • Connect Tech

    GraphiteVPX/GbE

    (26 pages)
    2 GraphiteVPX/GbE 20-Port Managed Carrier Ethernet Switch Connect Tech Inc. Tel: 519-836-1291 42 Arrow Road Toll: 800-426-8979 (North America only) Guelph, Ontario Fax: 519-836-4878 N1K 1S6 Email: [email protected] www.connecttech.com [email protected] CTIM-00461 Revision 0.02 2016/10/27 …
  • FLIR

    ACC60WPMS1

    (2 pages)
    ACC60WPMS1_QSG_EN_R1Quick Start GuideACC60WPMS1High PoE MidspanConnectionPackage Contents• High PoE Midspan• Power Cable• Mounting Screws (×3)• Quick Start GuidesDimensionsConnect the midspan to a power source using the included power cable.3Up to 328ft / 100mFront PanelSwitch / NVR* 12Compatible Network Camera*6.0” 151mm1.6” 39mm2.8” / 71mmF …

Comments, Questions and Opinions: