HP Edgeline EL1000 Operation & User’s Manual

Text of HP Edgeline EL1000 User Guide:

• HP Edgeline EL1000, Support and other resources Websites • Hewlett Packard Enterprise Information Library • Hewlett Packard Enterprise Support Center • Contact Hewlett Packard Enterprise Worldwide • Subscription Service/Support Alerts • Software Depot • Customer Self Repair • Insight Remote Support • Serviceguard Solutions for HP-UX • Single Point of Connectivity Knowledge (SPOCK) Storage compatibility matrix • Storage white papers and analyst reports Accessing Hewlett Packard Enterprise Support • For live assistance, go to the Contact Hewlett Packard Enterprise Worldwide website: http://www.hpe.com/assistance • To access documentation and support

• HP Edgeline EL1000, 1 2 1 Installing the drive Procedure 1. Align the drive to the drive bay, and slide it into the bay until it clicks in place. 2. Close the locking latch to secure the drive. Installing the card options Depending on the configuration of your system, perform one of the following procedures: • Install the PCIe card • Install the PXI/PXIe card Install the PCIe card About this task The system supports optional PCIe cards. 28 Installing the drive

• HP Edgeline EL1000, 3 1 2 Installing a full-length mini-PCIe module Procedure 1. Align the full-length mini-PCIe module with the full-length slot on the mini-PCIe adapter board. 2. Insert the mini-PCIe module connector into the slot. 3. Using a Phillips screwdriver, insert and tighten the two screws to secure the mini-PCIe module to the board. 1 3 2 32 Installing a full-length mini-PCIe module

• Procedure • Use one of the following methods to power down the system: ◦ Press and release the Power On/Standby button of the cartridges installed in the system. This method initiates a controlled shutdown of applications and the OS before the system enters standby mode. ◦ Press and hold the Power On/Standby button of the cartridges installed in the system for more than 4 seconds

• HP Edgeline EL1000, Install the PXI/PXIe card About this task The system supports optional PXI cards. NOTE: The PXI/PXIe card is not hot-pluggable. The system must be powered down to install this card. Procedure 1. Power down the system. 2. Remove the PXI/PXIe blank screws, and then remove the blank. 1 1 2 3. Align the PXI/PXIe card to the PXI/PXIe slot in the front panel. 4. Bend the tab and slide the PXI/PXIe card in until it clicks in place. 5. Install the PXI/PXIe card slot screws. 1 2 3 3 30 Install the PXI/PXIe card

• HP Edgeline EL1000, 4. Align the system to the ETSI bracket. 5. Secure the system in the ETSI rack mount. Installing the Enterprise rack mounting option kit Procedure 1. Install the rails on the rack. For more information on installing the rack rails, see the Quick Deploy Rail System Installation Instructions that ships with the rack hardware kit. 2. Install the cable management arm. For more information on installing the cable management arm, see the HP 1U Cable Management Arm Option Installation Instructions that ships with the cable management arm kit. 3. Install the Enterprise rack mount onto the rails. 4. Remove the system reten

• HP Edgeline EL1000, Installing hardware options Install any hardware options before initializing the system. For options installation information, see the option documentation. For system-specific information, see "Hardware options installation." Registering the product To experience quicker service and more efficient support, register the product at the Hewlett Packard Enterprise Product Registration website. Installing hardware options 23

• 5. Once completed, press ESC to back out of the menus. Save the settings when prompted. 6. After saving all settings, iLO prompts for a reset in order for the new settings to be used. Reset the system. 36 Configuration

• HP Edgeline EL1000, Troubleshooting HPE Edgeline Troubleshooting Guide The HPE Edgeline System Troubleshooting Guide provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, issue resolution, and software maintenance on the Edgeline System. The document is available in the Hewlett Packard Enterprise Information Library. Troubleshooting 43

• Setting the static IP address using the serial console cable Procedure 1. Access the System Utilities menu. 2. Navigate through the menu options System Configuration > iLO 4 Configuration Utility > Network Options. The Network Options screen displays. 3. Change DHCP Enable to OFF. 4. Configure the IP Address, Subnet Mask, and Gateway Address as required. The follow

• HP Edgeline EL1000, Contents Component identification.......................................................................6 PCIe configuration........................................................................................................................ 6 Front panel components.................................................................................................... 6 Front panel LEDs and buttons........................................................................................... 6 Right side components.......................................................................................................7 System board

• HP Edgeline EL1000, Specifications Product QuickSpecs For more information about product features, specifications, options, configurations, and compatibility, see the product QuickSpecs on the Hewlett Packard Enterprise website. Environmental specifications Table 2: Standard specifications Specification Value Temperature range 1 — Operating 10°C to 35°C (50°F to 95°F) Nonoperating -30°C to 60°C (-22°F to 140°F) Relative humidity (noncondensing) — Operating 8% to 90% at 28°C (82.4°F) maximum wet bulb temperature Non-Operating 5% to 95% at 38.7°C (101.7°F) maximum wet bulb temperature 1 All temperature ratings shown are for sea level. An altitude derating of 1.0°C per 304.8 m (1.8�

• Accessing updates • Some software products provide a mechanism for accessing software updates through the product interface. Review your product documentation to identify the recommended software update method. • To download product updates: Hewlett Packard Enterprise Support Center www.hpe.com/support/hpesc Hewlett Packard Enterprise Support Center: Software downloads www.hpe.com/suppor

• HP Edgeline EL1000, Electrostatic discharge Preventing electrostatic discharge About this task To prevent damaging the system, be aware of the precautions you must follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. Procedure • Avoid hand contact by transporting and storing products in static-safe containers. • Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations. •

• HP Edgeline EL1000, HPE Proactive Care advanced service: Supported products list www.hpe.com/services/proactivecareadvancedsupportedproducts Proactive Care customer information Proactive Care central www.hpe.com/services/proactivecarecentral Proactive Care service activation www.hpe.com/services/proactivecarecentralgetstarted Support and other resources 59

• HP Edgeline EL1000, Item Description Status 3 Cartridge UID LED/button • Blue = Cartridge ID is selected • Flashing Blue = Cartridge firmware update is in progress or iLO IRC is in use • Off = Cartridge ID is not selected 4 Cartridge health LED • Green = Normal operation • Flashing Amber = Degraded condition • Flashing Red = Critical condition • Off = No power 5 Cartridge power LED • Green = Normal operation • Flashing green = iLO booting • Amber = Standby operation • Off= No power Right side components 1 2 3 4 Item Description 1 Antenna connectors 2

• HP Edgeline EL1000, 3. Install the system in the rack mount. Installing the ETSI rack mounting option kit Procedure 1. Align the rack mount bracket to the system. 2. Using a Torx driver, insert and tighten four T-10 Torx screws to secure the bracket to the system. 3. Install the ETSI brackets to the rack: a. Align the bracket to the rack rail. b. Using a Torx driver, insert and tighten two T-20 Torx screws to secure each bracket to the rack rail. Installing the ETSI rack mounting option kit 25

• 4 Drive status Solid green The drive is a member of one or more logical drives. Flashing green The drive is rebuilding or performing a RAID migration, strip size migration, capacity expansion, or logical drive extension, or is erasing. Flashing amber/ green The drive is a member of one or more logical drives and predicts the drive will fail. Flashing amber Th

• HP Edgeline EL1000, HPE EMC compliance testing Emissions classification FCC rating Class A EMC Normative standards • CISPR 22 • EN55022 • EN55024 • FCC CFR 47 • Pt 15 • ICES-003 • CNS13438 • K22 • K24 • EN 61000-3-2 • EN 61000-3-3 • EN 60950-1 • IEC 60950-1 NOTE: Product conformance to cited product specifications is based on sample (type) testing, evaluation, or assessment. This product or family of products is eligible to bear the appropriate compliance logos and statements. System synchronization clock specifications 10 MHz system reference clock: PXI_CLK10 Specification Value Maximum slot-to-slot skew 1 ns Accuracy ±25 ppm max (guaranteed over the operatin

• HP Edgeline EL1000, Installing the mini-PCIe module options You can install the following mini-PCIe modules on the mini-PCIe adapter board: • Up to two half-length mini-PCIe modules • Up to two full-length mini-PCIe modules Install a half-length mini-PCIe module option About this task You will need a half-length mini-PCIe module adapter provided with the WiFi option kit to install this option. Procedure 1. Install the adapter using the two holes of the half-length mini-PCIe module. 1 1 2 2. Insert the mini-PCIe module connector int

• HP Edgeline EL1000, Using UEFI System Utilities To use the System Utilities, use the following keys. Action Key Access System Utilities F9 during server POST Navigate menus Up and Down arrows Select items Enter Save selections F10 Access Help for a highlighted configuration option 1 F1 1 Scan the QR code on the screen to access online help for the UEFI System Utilities and UEFI Shell. Default configuration settings are applied to the server at one of the following times: • Upon the first system power-up • After defaults have been restored Defau

• HP Edgeline EL1000, Documentation feedback Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback ( [email protected]). When submitting your feedback, include the document title, part number, edition, and publication date located on the front cover of the document. For online help content, include the product name, product version, help edition, and publication date located on the legal notices page. Documentation feedback 61

Related Products and Documents (PCI Card):

Comparable Devices:

Similar Resources:

• Zonet ZEW1605A (2 pages) ZEW1605A802.11g Wireless PCI AdapterPRODUCT DATAThe Zonet ZEW1605A - 802.11g Wireless PCI Adapter w/Extended Antenna delivers incredible wireless speed to your desktop PC without running wires. It complies with the IEEE 802.11g standard and backward compatible with 802.11b networks. Advanced wireless encryption p …

• LaCie FireWire 800 (40 pages) LaCie d2 Quadra • Design by neil Poulton Table of ContentsUser Manual page 1Table of ContentsHealth and Safety Precautions 3General Use Precautions 31. Introduction 41.1. Box Content ............................................................................................................................................... 51.2. Minimum System Requi …

• Quectel EC20 (8 pages) TITLEPROJECT1.0EC20 Reference DesignRadom.XIANGMountain.ZHOUCHECKED BYDRAWN BYOFA654321SHEETABCD123456DCBQuectel Wireless SolutionsSIZEVER81 DATE2015/3/30A2Module Interface1. Keep all RESERVED and unused pins unconnected.Notes:2. Pin 73~84 and 117~140 are unused in the design. You can ignore them in schematic and PCB decal.Module Interface3. The DBG_RXD/DBG_ …

• Moxa Technologies POS-104UL Series (2 pages) — 1 — — 2 — — 3 — POS-104UL Quick Installation Guide First Edition, January 2007 1. Overview The POS-104UL is a 4-port RS-232 Universal PCI serial board that is ideal for connecting a wide range of serial devices to a PC. Suitable devices include terminals, modems, printers, scanners, cash registers, bar code readers, keypads, numeric disp …

• YASKAWA DX200 (98 pages) MANUAL NO. HW1482183Part Number: 165553-1CDRevision: 33DX200 OPTIONSINSTRUCTIONSFOR CONVEYOR SYNCHRONIZED FUNCTION WITH SHIFT FUNCTIONSUpon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain for future reference.MOTOMAN INSTRUCTIONSMOTOMAN- INSTRUCTIONSDX200 INSTRUCTIONSDX200 OPERATOR’S MANUAL (fo …

• StarTech.com 6P6G-PCIE-SATA-CARD (2 pages) Quick-Start GuideTo view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.Manual Revision: June 17, 2021Product Diagram (6P6G-PCIE-SATA-CARD)Front ViewPort Function 1 SATA Ports x 6• Connect SATA Stoage Devices to the PCIe SATA Card using a SATA Cable2 PCIe x4 Connector• Connect the PCIe SATA Card …

Comments, Questions and Opinions: