IRIS 106 User Manual & Installation Manual

Text of IRIS 106 User Guide:

• IRIS 106, Warnings & Regulatory Information Do not use harsh chemicals or cleaning solvents to clean the device. Do not attempt to dismantle the device. Unauthorized modifications or attachments could damage the device and may violate regulations governing radio devices. Any modification to the products cable tail may invalidate the product warranty. Please contact Iris Innovations before attempting any modification to the cable. Avoid dropping, knocking or excessively shaking the device. Rough handling can break internal circuit boards and fine mechanics. Observe co

• IRIS 106, Introduction The IRIS106 is a fully controllable Pan, Tilt and Zoom CCTV camera with low light operation, designed specifically for use on boats as a security safety and situational awareness aid. The Camera is designed to be a small and low-profile as possible so that it doesn’t protrude too much from head linings and so that it blends into the aesthetic of the vessel. It’s marine grade stainless steel bezel features a high polish finish and the mirrored dome provides enhanced privacy. Key features include: • Sony High Resolution Camera Modul

• IRIS 106, Installation To install the IRIS106 you will need the following tools: • Drill with 105mm Hole Saw • Drill Bit for Pilot Holes (2mm) • Cross Headed Screw Driver • Hand tools for connecting cables (unless pre-made cables are being used), including wire cutters, wire stripper. • Appropriate tool for terminating BNC connector (unless pre-made cables are being used), such as knife to remove coax cable outer sheath and dielectric, BNC Crimp Tool, Cable Insulation Stripper. • Marine Sealant Before you begin the installation, please take time to consider the

• IRIS 106, example). If possible, power the item up and offer the camera up in the vicinity of the desired installation position to double check suitability. Cabling: The camera has a 30cm cable tail which has a 2.5mm DC Barrel Jack (female) to connect power, bare stripped and tinned wires (colour coded red and black) for the RS485 serial control data) and a 75Ω BNC (female) connector for the video signal, therefore it will be almost inevitable that the power, data and video cables will need to be extended

• IRIS 106, Video Distribution Amplifier IRISVDA0208 RS485 Serial Data Distributor IRISEXP0204 Fig:2.0. Slightly more complex set up with 4 IRIS106 cameras being controlled and viewed at 2 separate helm positions. Data from each controller is fed into the input of the RS485 Serial Data Expander, and data to each camera is connected to the outputs. This keeps the data ‘clean’ and prevents data cross talk and over-runs. Video from each camera is fed into a VDA (Video Distribution Amplifier), which feeds two MFD’s. Power not shown to keep diagram simple.

• Cabling (continued...) The following cable specifications apply: Video: 75Ω Coaxial Cable such as RG59, URM70, RG174 Mini-Coax. Data: Single Twisted Pair Power: 2 core. Rated 12VDC - max Current 1A Individual cables can be run for each of the above, or 'Combination' (Combi) cables can be used. Iris Innovations supply pre-made cables to length. Please contact Iris for more d

• IRIS 106, Camera Address (continued...) The example below (Fig 3.0) shows the camera address set to 1, as switch 1 is set to the ON position as shown by the arrow. As the switches set the binary address, to set the cameras address to 2, set switch 1 to OFF and switch 2 to ON. To set the camera to address 3, ensure both switches 1 and 2 are set to the ON position. For address 4, switches 1 and 2 should be OFF and switch 3 should be ON. The value of each switch doubles. The value of each individual switch is listed below: Switch 1 = 1.

• Fitting the Camera: Step 1: After you have established the desired mounting position and are happy there are no obstacles behind the surface into which you are drilling, use a 105mm hole saw to carefully create the circular recess into which the camera body will sit. Step 2: Once the mounting hole has been cut offer the camera into place and mark off the 4 fixing holes.

• IRIS 106, Operation Now the camera is installed, powered up from a suitably rated and protected 12VDC power source and the video is hooked up to the monitoring (or switching / recording / routing ) equipment, the camera can be controlled using any controller, MFD or interface that supports the widely available Pelco D protocol. Panning: The camera pans through 360˚ continuously. Simply move the controller in the desired direction of travel. Tilting: The camera tilts through 180˚ with an automatic ‘Auto-Flip’ feature

• IRIS 106, at the touch of a button. Refer to the documentation of the controller for details on how to save and recall preset positions. OSD Menu (Extended Features) The camera features many extended features and settings that are accessed via an On Screen Display (OSD) menu. OSD Menu functionality may or maynot be supported depending on the control interface. The OSD Menu is accessed by calling Preset 95. To exit the OSD menu call preset 56. Navigating OSD Menu • Menu items with <> symbols indicate a drop down menu • To access sub-menu, press either Near Focus or move j

• IRIS 106, Camera Address Table This table lists the DIP switch set- tings to set address 1 through 75. For information on how to set ad- dresses 76 through 254 please con- tact Iris Innovations Technical Sup- port. View other Marine Electronics & Navigation made by IRIS Products on our website.

Related Products and Documents (Security Camera):

Comparable Devices:

Similar Resources:

• Harbor Freight Tools 91851 (10 pages) RAINPROOF* COLOR & NIGHTVISION CAMERA SECURITY SYSTEMModel 91851ASSEMBLY AND OPERATING INSTRUCTIONS3491 Mission Oaks Blvd., Camarillo, CA 93011Visit our Web site at: http://www.harborfreight.comCopyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of thismanual or any artwork contained herein may be reproduced in any shape or form …

• Okina SEMT-7680 (32 pages) SEMT-7680 680 TVL SEMT-7610 610 TVL Day & Night Box Camera - Effio-E with Mechanical IR Cut Filter (ICR) Thanks for purchasing our product. Before operating the unit, please read the instructions carefully and keep this manual for future reference. …

• Speco CVC-5815DNV (1 pages) simply uniqueIntense-IR SeriesWeather ResistantColor Day/Night Bullet CameraIRMPINTENSE-IR Camera9.06” L3.94” W4.92” HFeatures• 1/3” Sony Super-HAD II™ CCD • 3D-DNR (sense-up) - sharp image under ultra low light level • Intense-IR function - no saturation image, vivid image• Defect function - elimination of white spots• HSBLC (High Light …

• ZUUM D4MP-IP-3.3-10.5-IR30-WH (7 pages) [email protected] * 1-888-861-7351 * www.zuum.life ZM020117 D4MP-IP-3.3-10.5-IR30-WH IP White Dome Camera 4 Mega Pixel, 3.3-10.5MM Lens, P2P, UPnP, PoE This is a great full-featured 4 mega pixel IP …

• Intellisystem IT750 (16 pages) Intellisystem Technologies S.r.l. http://www.intellisystem.itIT750/IT750W/IT750W-LR Network Camera with Pan/Tilt/ZoomQuick Installation GuideThis guide describes the basic functions of IT750/IT750W/IT750W-LR Network Camera. All detailed information is described in the user's manual. …

• American Dynamics ADC720D (2 pages) D A T A S H E E TADC720 SeriesColor Specialty CamerasFeatures That Make a Difference: 1/3-inch interline color imager, NTSC format 330-line color imager Sharp picture Sensitive to IR illumination and weather resistant (ADC722WP) Discreet housings Automatic electronic shutter Automatic gain control Auto tracing white balance 12 VDC input v …

Comments, Questions and Opinions: