AMX AXB-F117 Stealth 1 Instruction Manual
|
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller Pre-Installation Settings 11 7. Carefully place the back panel onto the main unit and align the screw holes. Make sure the cables are not pinched in the back panel or drive gears. 8. Insert the four pan-head screws and tighten. Note The communication settings for RS-232 mode are: • 9,600 baud • No parity • 8 bits • 1 stop bit
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller AXCESS Programming 47 RS-232 Send_Strings (Cont.) Command Function "27,20,0" De-asserts RTS hardware handshake output high. "27,20,1" Assert an RTS hardware handshake output low. If you need to send a string containing sequences "27,18," "27,19," or "27,20," use two Send_String commands; the first containing characters up to and including "27," the second beginning with "18," "19," or "20," "27," and all subsequent characters. To send the string " $1B,'C&apo
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller Table of Contents i Table of Contents Introduction ...........................................................................1 Overview 1 Features 1 What’s New 2 Application 3 Servomotor Mode 3 Positional mode 4 Speed mode 4 Motor Mode 4 Pre-Installation Settings.........................................................5 Overview 5 Configuration Settings 5 Setting zoom, focus, and iris jumpers to servomotor or motor mode 6 Setting zoom, focus, and iris switches to servomotor or motor mode 7 Setting the RS-232 DIP switch (S1) 7 Setting the AXlink D
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller AXCESS Programming 27 AXCESS Programming Overview This section describes the AXCESS programming commands and functions for the AXB-F117. The AXB-F117 control capabilities for camera functions include: • Pan • Focus (servomotor; speed) • Tilt • Focus (motor drive) • Zoom (servomotor; positional) • Iris (servomotor; positional) • Zoom (servomotor; speed) • Iris (servomotor; speed) • Zoom (motor drive) • Iris (motor drive) • Focus (servomotor; positional) The AXB-F117 is controlled with device-specific channel settings and AXCESS Se
AMX AXB-F117 Stealth 1, 32 AXCESS Programming AXB-F117 Stealth 1 Camera Controller Channel commands for motor-mode functions (Cont.) Channel State Function 20 On Zoom + at 50% speed 24 On Zoom - at 50% speed 21 On Focus + at 50% speed 25 On Focus - at 50% speed 18 On Iris + at 50% speed 22 On Iris - at 50% speed Preset functions Figure 37 lists preset functions. Preset functions Channel State Function 50 On Pan is seeking POT preset (status only). 51 On Tilt is seeking POT preset (status only). 52 On Zoom is seeking POT preset (stat
AMX AXB-F117 Stealth 1, 18 Installation AXB-F117 Stealth 1 Camera Controller Wiring guidelines The AXB-F117 requires 12 VDC power to operate properly. The power can be supplied by the AMX Control System’s AXlink cable or with an optional 12 VDC power supply. The maximum wiring distance between the control system and AXB-F117 unit is determined by power consumption, supplied voltage, and the wire gauge used for the cable. Figure 21 lists wire sizes and the maximum lengths allowable between the AXB-F117 and AMX Control System. The maximum wiring lengths are based on a minimum of 13.5 volts available at the power supply output connector. To reduce the possible effects of ground loop noise in t
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller AXCESS Programming 31 Channel commands for servomotor speed mode lens functions Figure 35 lists channel commands for servomotor speed mode lens functions. Channel commands for servomotor speed mode lens functions Channel State Function 12 On Zoom + at maximum speed (output maximum voltage) 16 On Zoom - at maximum speed (output minimum voltage) 13 On Focus + at maximum speed 17 On Focus - at maximum speed 10 On Iris + at maximum speed 14 On Iris - at maximum speed 20 On Zoom + at 50% speed 24 On Zoom - at 50% speed 21 On Focus + at 50% speed 25 On Focus - at 50% speed 18 On Iris + at 50% speed 22 On Iris - at 50% speed Channel
AXB-F117 Stealth 1 Camera Controller Installation 13 Installation Overview This section contains AXB-F117 mounting and wiring information. Mounting the AXB-F117 You can mount the AXB-F117 to a flat surface using the optional WM-CAM Wall Mount kit. Figure 15 shows the AXB-F117’s dimensions 3.87 (98.2 mm) 3.11 (78.9 mm) 2.20 (55.8 mm) 7.90 3.00 8.06 (204.7 mm) 1.00 To mount the AX
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller Pre-Installation Settings 7 Setting zoom, focus, and iris switches to servomotor or motor mode The AXB-F117 supports servomotor (+2.5 to +7.5 VDC operating range) and direct- drive motor ( ± 6 VDC or ± 12 VDC operating range) lens control. Figure 6 shows how to set the switches for servomotor mode (S) or motor mode (M). If you are using a direct-drive lens, refer to the manufacturer's literature to set the VOLT switch for ± 6 or ± 12 VDC control. Servomotor and motor voltage switch settings Serv
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller AXCESS Programming 45 RS-232 commands (Cont.) Command Function 'HSOFF' Disable hardware handshaking (default). Example: SEND_COMMAND CAM,'HSOFF' Disables hardware handshaking on the device. 'HSON' Enable hardware handshaking. Example: SEND_COMMAND CAM,'HSOFF' Enables hardware handshaking on the device. 'RXCLR' Clear characters waiting in the receive buffer pending transmission to the Central Controller. Example: SEND_COMMAND CAM,'RXCLR' Clears the characters in the receive butter waiting to be sent to the Central Controller. 'RXOFF&
AMX AXB-F117 Stealth 1, 38 AXCESS Programming AXB-F117 Stealth 1 Camera Controller Preset parameters and commands Figure 41 lists preset parameters and Figure 42 lists the preset commands. Preset parameters Preset: 1 - 255 TIME: (Optional) If specified, 0 to 255 in tenth seconds. If not specified, at current rate. Used for voltage outputs. Used only for recall preset. SPEED: (Optional) 0 to 127. 0 is slowest and 127 if fastest. If not specified, at current speed. Used for Motor Drive outputs, including pan/tilt control. Used for Recall Preset only. Pres
AXB-F117 Stealth 1 Camera Controller Installation 23 a. Move the adjustable pan-limit stop slightly farther until you hear a click. The click indicates the pan-limit switch is engaged. b. Tighten the left adjustable pan-limit stop. Tilt-limit switch Adjustable tilt-limit stops Installation notch for the adjustable tilt-limit stops Pan-limit switch Adjustable pan-li
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller AXCESS Programming 35 Send_Commands (Cont.) Command Description 'G<output 3-4>L<position 0-255 or 0-65535>' Turn on the specified output at the current speed until the specified position as read by the POT input is reached. Command forces output to go to a preset position using the POT input as a reference. (Positions 0- 65,535 are available using the 'AD MODE x 10' command.) This command can be used for motor-mode and servomotor speed-mode applications. Example: SEND_COMMAND CAM,'G3L100' Sets ZOOM to search for position 100 as referenced by the ZOOM POT input. 'G<output 1-4>D<deviation 0- 127>
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller Introduction 3 Application Figure 2 shows a sample camera control application using the AXB-F117. PS6.3 Power supply PS6.3 Power supply AXlink AXP-CCS AXB-EM232 Stealth 1 Stealth 1 PC or other RS-232 Controller Application #2 – RS- 232 Application #1 - AXlink PS2.8 Power supply Servomotor Mode Servomotor mode is used when the lens requires a low control voltage to a servomechanism, which in turn supplies drive voltages to the lens motor. This method is generally used in
16 Installation AXB-F117 Stealth 1 Camera Controller 5.0" (127.0 mm) 4.0" (101.6 mm) 4.0" (101.6 mm) 5.0" (127.0 mm) 5/8" (.625") (15.9 mm) 1.0" (25.4 mm) 18.0" (457.2 mm) 3.0" (25.4mm) Pan/tilt mounting plate Wall mounting plate 5. Mount and balance the camera and lens on the AXB-F117. Figure 18 WM-CAM Wall Mount
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller Pre-Installation Settings 5 Pre-Installation Settings Overview This section describes the pre-installation configuration settings, and DIP switch settings for AXlink or RS-232 communication mode. Configuration Settings Your AXB-F117 comes with either jumpers or switches for setting control mode and lens control voltage, depending on the revision of the circuit board. Before installing the AXB-F117 controller, you must set the DIP switches, lens control mode jumpers (or s
AMX AXB-F117 Stealth 1, ii Table of Contents AXB-F117 Stealth 1 Camera Controller Replacing the Lithium Battery.............................................. 25 Overview 25 Replacing the Battery 25 AXCESS Programming ........................................................ 27 Overview 27 Configuration Commands 27 Channel Commands 30 Channel commands for pan/tilt functions 30 Channel commands for servomotor positional mode lens functions 30 Channel commands for servomotor speed mode lens functions 31 Channel commands for motor-mode functions 31 Preset functions 32 Levels 32 Send_Commands
AMX AXB-F117 Stealth 1, 34 AXCESS Programming AXB-F117 Stealth 1 Camera Controller Send_Commands (Cont.) Command Description 'G<output 1-5>R<ramp time 1- 255>' Sets the ramp time (in 10ms increments) for future Send_Commands and channel commands on motor drive outputs. (Added v1.10) The acceleration ramp feature allows the pan/tilt motors to ramp to the desired operational speed, resulting in smoother motion. This feature also reduces stress and undesirable vibration of the pan/tilt mount. The default is set for 250ms. Example: SEND_COMMAND CAM,'G1R25' Sets PAN to ramp to desired speed within 250ms for future commands. 'G<
AMX AXB-F117 Stealth 1, 22 Installation AXB-F117 Stealth 1 Camera Controller Servomotor-driven outputs are intended to drive servo-type motors only! The outputs have very low current (milliamp range) capability. DO NOT attempt to drive conventional motors with these outputs or you will damage the output drivers. If you are not sure about the motor type, refer to the Technical Support section and contact AMX Corporation for assistance. Using the camera control RS-232 DB-9 connector Connect the AXB-F117 RS-232 DB-9 (male) connector to the camera head’s RS-232 connector. Figure 28 shows the DB-9 connector and Figure 29 li
AMX AXB-F117 Stealth 1, AXB-F117 Stealth 1 Camera Controller Installation 17 Wiring the Connectors The AXB-F117 has an AXlink 4-pin connector, a camera control RS-232 DB-9 connector, and lens control DB-15 high-density connector. Figure 20 shows the location of each connector on the AXB-F117. AXlink 4-pin (male) connector Camera control RS-232 DB-9 (male) connector Lens control DB-15 high- density (female) connector AXB-F117 (rear view) Preparing captive wires You will need a wire stripper, soldering iron, and flat-blade screwdriver to prepare and connect the captive wires. 1.
Net Media NM-VIDEYE Security Camera Specifications
NM-VIDEYE |
AMX UDM-1604 Security Camera Quick start manual
UDM-1604 |
JVC KY-F550 Security Camera Instruction manual
KY-F550 |
Samsung SCC-B5394 Security Camera Operation & user’s manual
SCC-B5394 |
DAGE-MTI CCD-100 Security Camera Operation & user’s manual
CCD-100 |
Vista VFD-MiniD Security Camera Installation manual
VFD-MiniD |
AMX PT10-PLV Security Camera Instruction manual
PT10-PLV |
Swann PRO-680 Security Camera Operating instructions manual
PRO-680 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Conceptronic | C300BRS4 | Quick installation manual | conceptronic/c300brs4-T6Y.pdf | 19 Sep 2023 | 234 | |
2 | Philips | AZ 7460 | User manual manual | philips/az-7460-K49.pdf | 23 Jul 2022 | 20 | 0.31 Mb |
3 | Tassimo | TAS 40XXKR | Instruction manual | tassimo/tas-40xxkr-828.pdf | 29 Dec 2022 | 34 | |
4 | Hotpoint | SX 896L PX S | Operating instructions manual | hotpoint/sx-896l-px-s-R2I.pdf | 07 Feb 2024 | 16 | 6.13 Mb |
5 | Lionel | Drawbridge | Owner's manual | lionel/drawbridge-1BQ.pdf | 08 Feb 2024 | 8 | |
6 | BenQ | E1240 | Operation & user’s manual | benq/e1240-7FL.pdf | 16 Apr 2023 | 38 |
Panasonic
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.The model number is abbreviated in some descriptions in this manual.Installation GuideNetwork CameraModel No. WV-SF135/WV-SF132WV-SF135E/WV-SF132EWV-SF135
…
WV-SF135(36 pages) |
GeoVision
Hardware ManualGV-IPCam H.264Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Fixed IP DomeTarget Fixed DomeICH264TG2V10
…
GV-FD220D(39 pages) |
Dakota Micro
Dakota Micro, Inc. Rev:06/26/17Page1of12 Author:CNRUsersManualAGCOAgCam®PartNumber:AC‐9MQ(‐C2) …
AC-9MQ(12 pages) |
ROHS
• Please unpack the box carefully and identify that all the parts are present.• Do not open the camera housing. This will void the warranty and break the warranty seal inside the camera.• Make sure you use only the recommended power supply. Damage caused to the camera by incorrect voltage or wiring is not covered by the warranty.Before you beginCOLOUR …
EVC422(24 pages) |
Vitek
VITEKVITEKFEATURES• 1/2.3” 8.0 Megapixel [4K] Progressive Scan CMOS Sensor• 8MP[4K]@15fps/12.5fps, 4MP@30fps/25fps, 1080P@30fps/25fps• True Day / Night by IR Cut Filter• HD-TVI / HD-CVI / AHD / 960H CVBS Video Output (Selectable)• 3.6~10mm Motorized Varifocal Lens• 6 Integrated High Power Dynamic IR LEDs with up to 165’ IR Range• …
TRANSCENDENT VTD-T4D6HR8MD(10 pages) |
Vicon
User Manual SN673V-C Cruiser™ Outdoor PTZ Dome Camera XX249-65-00 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be use …
Cruiser SN673V-C(92 pages) |
Mitsubishi Electric Desktop Apricot LS700Mitsubishi Electric Desktop Owner's handbook manual (File: mitsubishi-electric-apricot-ls700-desktop-123, Monday 04-09-2023) Apricot LS700, 123 |
Addonics Technologies Computer Accessories CA256USBAddonics Technologies CA256USB User Guide (Doc Type: Computer Accessories Operation & user’s manual) CA256USB, 6 |
Philips Blu-ray Player BDP3406/F7#V8H452 BDP3406/F7: Philips Blu-ray Player Owner Documentation BDP3406/F7, 61 |
Kenmore Oven ELECTRIC BuILT-IN OVENOven #7AFNVI ELECTRIC BuILT-IN OVEN, 22 |
Sony Adapter PSone SCPH-170 USony Adapter PSone SCPH-170 U Instruction manual PSone SCPH-170 U, 2 |
FUNAI TV VCR Combo Emerson EWC1301FUNAI TV VCR Combo Owner's manual (File: funai-emerson-ewc1301-owner-s-manual-32, Fri 01.2024) Emerson EWC1301, 32 |
KUSSMAUL Other 091-160Other PDF Installation and operation manual 091-160, 2 |
Samsung LCD TV LN46A650Samsung LN46A650 User Manual (Doc Type: LCD TV Operation & user’s manual) LN46A650, 118 |
Sanyo Projector PLC-510M#87QP67: PLC-510M Projector Owner's manual PLC-510M, 24 |
IBM Desktop LS21 - BladeCenter - 7971LS21 - BladeCenter - 7971 Installation and user manual - 85912V LS21 - BladeCenter - 7971, 84 |
Andor Technology Security Camera Apogee AspenSecurity Camera Quick start manual (Andor Technology Apogee Aspen) Apogee Aspen, 2 |
Canon Camcorder ETT555Canon Camcorder Basic use (File: canon-ett555-using-1, 20th Jan 2024) ETT555, 1 |