MFJ MFJ-434B Instruction Manual
|
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 1 INTRODUCTION The MFJ-434B was designed by contesters and optimized to perform under the toughest operating conditions. You don't need to be a contest superstar to appreciate what the MFJ-434B can do. Even casual operators will discover the MFJ-434B is packed with user-friendly features that make operating, both in and out of contests, more enjoyable and fun. Set it up, and you'll be amazed how quickly it becomes part of your operating routine. Before you begin, pleas
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 2 Once again, this manual contains important technical information and operating instructions you'll need to know before using your keyer. Please read it thoroughly, and enjoy operating to the fullest! POWERING YOUR MFJ-434B Important Note : We recommend turning your radio on before powering up the voice keyer. When some transceivers are turned off, the PTT line may be held low.
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 3 IMPORTANT WARNING: Remove the 9-volt battery when storing the keyer for extended periods. Remember to reinstall the insulating sleeve on the snap clip. CONNECTING AND OPERATING THE MFJ-434B Front Panel: MFJ Voice Keyer POWERMIC XMIT VOLUME MESSAGES REPEAT DELAY ON STOP MSG 1 MSG 2 MSG 3 MSG 4 MSG 5 PLAYREC ONINT. EXT. INTERNAL MIC. EXTERNAL MIC. RECORD PLAY X10 X1 OFFOFF MFJ -43
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 4 Rear Panel: AUDIO OUT OUTPUT LEVEL CONTROL POWER 12VDC - + AUDIO IN STOP MSG1 MSG2 MSG3 MSG4 MSG5 /XMIT GND TO RADIO MIC. MFJ ENTERPRISES, INC. STARKVILLE, MS USA REMOTE Power Requires 9-16 Vdc @ 100mA Audio Out Monitor audio output, ~500 mW max Output Level Control Adjusts microphone output level to radio Audio In 600 Ohm input jack for recording external signals Remote Port Remote access to messages and transmit busy lines To Radio Mic Audio/PTT (RJ-45) output for radio&
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 5 IMPORTANT WARNING: The MFJ-434B's internal jumpers are factory set for compatibility with Yaesu transceivers (FT-817, FT-857, FT-897) using conventional dynamic or crystal microphones. When using Icom or Kenwood/Alinco products, internal jumpers must be reset for the correct manufacturer and microphone voltage. Microphone Jumper Configuration (Icom, Kenwood, Yaesu) 1. Disconnect any 12VDC source from the
MFJ-434B Instruction Manual Voice Keyer 6 Front Panel View 87654321 8 7 6 3 4 5 2 1 3. JMP4 and JMP9 (Mic): Place jmp 4 and jmp 9 on the corresponding pin number required by your microphone. This pin number can be determined from the front panel view above. For example if your radio has Mic
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 7 IMPORTANT WARNING: Do not inadvertently change the jumper on HD1. This jumper is set on pins 7-8 and should not be moved. Other Internal Adjustments Please note two other important internal settings while the cover is off and the pc board visible: 1. Dual Gain Control, R29: This trimpot, located next to the audio isolation transformer, sets the overall adjustment range of the Output Level Control located on the rear panel. If you find the back panel gain contro
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 8 Remote message control lines are provided at the back panel via a male 8-pin IDC plug. This provides individual access to all five memory lines (MSG1-MSG5) plus the stop message line (Stop). All lines are isolated by a buffer, and are CMOS and TTL level compatible. A special output line provides 12 Vdc at low current when the voice keyer is not transmitting. This line goes logic low when the keyer transmits (Xmit), and can sink more than 20 mA. Another p
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 9 C. Off-Air or External Audio Source: Set Mic switch to Int and plug a line level audio source into the Audio In jack on the rear panel. Installing a plug in the Audio In jack disables the electret mic. Line level sources should not exceed 0-dBm. 4. Select A Message Slot: Choose from MSG1-MSG5 on the front panel. Press your selection and watch the Rec LED (it should flash within about two seconds). The first flash indicates recording has begun. To avoid recording "dead air", begin speaking the moment the red Rec LED starts flashing.
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 10 MSG1 MSG2 MSG3 MSG4 MSG5 075 Total Time in Seconds 32 42 52 62 32 10 10 10 13 Slot Size in Seconds This feature enables you to load up to a 75 second message in MSG1, should you need a long recording (progressively fewer slots are available as your message grows in length). When the memory limit is reached, the red Rec LED will stop blinking and the record function will stop automatically. With a little practice, you can use this protocol to extend your unit's flexibility. Message Playback Until
MFJ-434B Instruction Manual Voice Keyer 11 C. Press any other MSG button to halt the current message and start a new one. 7. Adjusting the Output Level Control: Before attempting to transmit recordings on air, you must set the Output Level control on the back panel for your keyer. Begin by r
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 12 3. Press the following buttons in the sequence shown. The green LED should blink once per operation. STOP → GREEN MSG1 → GREEN MSG2 → GREEN MSG3 → GREEN MSG4 → GREEN MSG5 → GREEN X1/X10 → GREEN STOP (REMOTE) → GREEN MSG1 (REMOTE) → GREEN MSG2 (REMOTE) → GREEN MSG3 (REMOTE) → GREEN MSG4 (REMOTE) → GREEN MSG5 (REMOTE) → GREEN PTT → GREEN 4. Turn the Repeat Delay pot fully counter-clockwise, then fully clockwise. The green LED should blink onc
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 13 keyer. The shield of the 8 conductor cable is connected to both the switch box chassis and voice keyer chassis. Do not connect the shield to the signal ground at either end, or erratic operation may result. STOP MSG1 MSG2 MSG3 MSG4 MSG5 XMIT GND (signal) REMOTE BOX IDC PLUG Shield NC Computer Interface The MFJ-434 selects memories through a buffered CMOS or TLL compatible interface. While this interface is relatively immune to ground loops (it takes almost 3 V RMS ripple to
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 14 R1 R2 R3 R4 R5 R8 R9 R10 R11 R12 C2 C3 C4 C5 C6 Q2 Q3 Q4 Q5 Q6 Signal Ground Stop MSG1 MSG2 MSG3 MSG4 MSG5 Ground XMIT R7 C1 Q1 R6 Computer MEM1 MEM2 MEM3 MEM4 MEM5 Abort R1-R6 470 Ohm R7-R12 1 K C1-C6 .01 uF Q1-Q6 2N3904 Parts List Cable Shielded Voice Keyer Chassis Ground Multi-Conductor SW RET The following is a cross reference for NA software: NA ABORT STOP MEM (1-5) M
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 15 Distorted Recordings from Audio In Jack: Are levels from your audio source exceeding the keyer's 0-dBm maximum input rating? If so, they must be attenuated. Weak or Noisy Recordings from Audio In Jack: Are levels from your audio source below the -23 dBm minimum operating level? If so, they must be boosted in some way. Voice Keyer Won't Activate PTT line on Playback: Check XMIT switch position. Pre-recorded Message
MFJ MFJ-434B, MFJ-434B Instruction Manual Voice Keyer 17 APPENDIX -At the MFJ factory, the interface is set for Yaesu transceivers with modular microphone connectors (FT-817, FT-857, FT-897). Y FT-897 FT-857 (modular) aesu FT-817 JMP 8 JMP 9 JMP 7 JMP 3 JMP 4 JMP 6 JMP 5 12 435687 JMP 2 Mic Mic Mic Gnd Mic Gnd PTT PTT PTT Gnd Direct Y (8-pin round) aesu FT-847 JMP 8 JMP 9 JMP 7 JMP 3 JMP 4 JMP 6 JMP 5 12 4 3568 7 JMP 2 Mic Mic Mic Gnd Mic Gnd
Saramonic Vmic Voice Recorder Manual
Vmic |
Olympus DM-550 Voice Recorder Specifications
DM-550 |
ESP Sting Voice Recorder Operation & user’s manual
Sting |
Sony ICD-P110VTP Voice Recorder Specifications
ICD-P110VTP |
Philips DVDR5570H Voice Recorder Specifications
DVDR5570H |
AJA Ki Pro Ultra Plus Voice Recorder Installation and operation manual
Ki Pro Ultra Plus |
Novus NVR-6332-H2 Voice Recorder Operation & user’s manual
NVR-6332-H2 |
Fostex DV40 Voice Recorder Supplement owner's manual
DV40 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Edge10 | W243h | Specifications | edge10/w243h-16S.pdf | 31 Mar 2024 | 1 | |
2 | Whirlpool | WERE3000PB5 | Use & care manual | whirlpool/were3000pb5-MJ8.pdf | 28 May 2023 | 40 | |
3 | Key Tronic | KB 5150 | Operator's manual | key-tronic/kb-5150-5F9.pdf | 18 Mar 2023 | 8 | |
4 | Electro Industries | Shark 200 | Installation & operation manual | electro-industries/shark-200-D74.pdf | 11 Sep 2022 | 178 | |
5 | Olympus | BX41-P | Instructions manual | olympus/bx41-p-71F.pdf | 30 Aug 2022 | 36 | |
6 | Xerox | 850DX - Phaser Color Solid Ink Printer | Operation & user’s manual | xerox/850dx-phaser-color-solid-ink-printer-WY7.pdf | 29 Oct 2022 | 106 | 2.92 Mb |
UPC
Horizon HD RecorderKurzanleitung / Guide d’utilisation Guida all’installazione rapida / Quick Guide Helpline: 0800 66 88 66 | upc.ch/support | upcch_care
…
Horizon(14 pages) |
Philips
1ConnectA Unplug the existing antenna cable from your TV and connect it to the DIGITAL ANTENNA INPUT socket on this recorder.B Connect the Tuner interlink cable (supplied) between DIGITAL ANTENNA LOOP THROUGH and ANALOG ANTENNA INPUT sockets on this recorder.C Connect the RF antenna cable (supplied) from the TO TV ANTENNA INPUT socket on this record …
DVDR5570H(2 pages) |
Bosch
DVR1C1161InstallatiehandleidingDigital RecorderNLIstruzioni sull’installazioneRegistratore digitaleITInstrukcja instalacjiCyfrowy magnetowidPLInstruções de InstalaçãoGravador DigitalPTInstallation InstructionsDigital RecorderENManuel d’installationEnregistreur numériqueFRInstallationshandbuchDigital RecorderDEManual de instalaciónGrabador digitalES …
DVR1C1161(25 pages) |
Olympus
DIRECTRECDR-1000Dictation KitThank you for purchasing anOlympus DIRECTREC.Please read these instructions for informationabout using the product correctly and safely.Keep the instructions handy for future reference.INSTRUCTIONSEN INSTRUCTIONS MODE D’EMPLOI INSTRUCCIONESENFRES BEDIENUNGSANLEITUNG ISTRUZIONI ИНСТРУКЦИЯDEITRU
…
DR 1000 - Directrec Dictation Kit(208 pages) |
Sony
Digital 4K Video Camera Recorder/Digital HD Video Camera RecorderFDR-X1000V/HDR-AS200VHow to useRead This FirstIdentifying the partsIdentifying the parts [1]Screen displayScreen display [2]Getting StartedChecking the bundled itemsChecking the bundled items [3]Inserting the battery packInserting the battery pack [4]Charging the battery packCharging the batter …
FDR-X1000V(124 pages) |
Sony
Sony CorporationPrinted in JapanPrinted on recycled paper.3-879-701-13(1)© 2008 Sony CorporationSolid-State MemoryRecorderOperating InstructionsBefore operating the unit, please read this manual thoroughly and retain it for future reference.PMW-EX30Printed in JapanPrinted on recycled paper.3879701130
…
PMWEX30(111 pages) |
Samsung DVD Recorder DVD-R130/XAA#1RGJ4D: DVD-R130/XAA DVD Recorder Service manual DVD-R130/XAA, 134 |
Amana Cooktop AKED3060Amana Product Guide: AKED3060 PDF Owner's manual - DP14TQ AKED3060, 20 |
Northern Security Camera CB700WANorthern CB700WA Security Camera Quick start manual CB700WA, 3 |
Supermicro Motherboard Supero X8SAX#WJO35Z: Supero X8SAX Motherboard Operation & user’s manual Supero X8SAX, 101 |
KitchenAid Microwave Oven KHMS1850SSS0Microwave Oven #629V9L KHMS1850SSS0, 12 |
Alvarion Network Hardware BreezeACCESS 900BreezeACCESS 900 (Network Hardware ePDF Manual, #389DDB) BreezeACCESS 900, 104 |
Philips Telephone TD9137T/194Manual: Philips TD9137T/194 (4KDWI9, Upd.07.09.2023) TD9137T/194, 2 |
Canon Scanner SCANFRONT M11058Scanner #IL739X SCANFRONT M11058, 28 |
Plantronics Headsets General Office Headset/Headset TelephoneGuide: Plantronics General Office Headset/Headset Telephone (R6136O, Upd.Thu 01.2024) General Office Headset/Headset Telephone, 2 |
ZyXEL Communications Network Card G-102ZyXEL Communications G-102 User Guide (Operation & user’s manual), @11INU3 G-102, 65 |
N'Finity Wine Cooler 273 02 50N'Finity 273 02 50 User Guide (Doc Type: Wine Cooler Instruction manual) 273 02 50, 12 |
IMT Lighting Equipment IQL Albireo FloodlightIQL Albireo Floodlight (Lighting Equipment ePDF Guide, #GL4FU9) IQL Albireo Floodlight, 12 |