Mitsubishi 7011A SERIES Owner Technical Manual

Text of Mitsubishi 7011A SERIES User Guide:

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 4-1 MITSUBISHI ELECTRIC 7011A SERIES UPS 4.0 RESPONSE TO UPS FAILURE Press the “MENU” button on the front panel. Then select “SILENCE” and press the “ENTER” button. Select “LOG” on the front panel and press “ENTER” button. Record fault code on a piece of paper. Refer to the list of fault codes for a description of the error. See section 6 For fault codes Take necessary action per the list of fault codes in section 6 of this manual. If Service is needed contact the Authorized Mitsubishi Service Representative or call Mitsubishi at: 1-800-887-7830. NOTE The

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-3 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.3 PROCEDURE FOR CABLE CONNECTION (Refer to Table 3.2 for cable sizes.) 1) Confirm the capacity of the UPS being installed. Identify the field terminal blocks as shown in the appropriate Figure 3.2 or Figure 3.3-Figure 3.5. 2) Referring to Figure 3.4-Figure 3.5., connect the grounding conductors from the input service entrance to the UPS ground bar. 3) Confirm that an external input circuit breaker sized to protect both the rectifier input and the bypass lines is installed. Consult equipment nameplate for curre

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-16 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.7 EXTERNAL BATTERY SET-UP PROCEDURES Please confirm the capacity of the external batteries. Press “MENU”, “ “ and “ “ buttons simultaneously for 3 seconds then Release. ENTER PIN 0*** - INCORRECT - SETUP 2.BATTERY Ah 14 -> 28Ah 1.LOG CLEAR NO Input PIN “ 1 2 2 5 ” (Using # ,$ and Enter) Adjust Ah of the external battery. Ah : Capacity of external battery. ( Ampere hour ) “Press ENTER” 3.BYP.SYNC.RANGE 3 -> 5% SETUP Top Page Press “CLEAR” MEASURE ¥ LOG ¥ SILENCE ¥ SETUP INV.OP

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-13 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.5 OPERATING PROCEDURES A) UPS Initial Startup Procedure Please be sure to confirm the internal maintenance bypass switch 52CS on “NORMAL” position before turn on AC input power. This procedure is only performed during initial start-up. B) UPS Start-up Procedure 1. Press and Hold “START” button for 0.5 seconds 2. The “INV.OP.” LED illuminates and the Inverter starts. C) Bypass Operation Procedure 1. Press “MENU” button and then select “BYPASS_OP.” and p

• MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 6-3 Note 1 Note 2 Note 3 Note 4 Failure Code Status Guidance Level Failure LED Buzzer Event Log 454 Module temperature high Reduce room temperature Minor Flicker 455 Bypass circuit abnormal Call service engineer Minor Flicker 456 Bypass Overload Reduce load Minor Flick

• MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-11 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.4.1 PROCEDURE FOR EXTERNAL BATTERY CONNECTION (OPTIONAL) 1. Installation procedure Please refer to the figure 3.6 or 3.7 for connection. Must connect external battery before internal battery is connected. 2. Set-up procedure Please confirm the

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-2 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.3 INSTALLATION PROCEDURE A) Note the load tolerance of the floor Refer to TABLE 3.1 for list of UPS weights: TABLE 3.1 List of UPS weights (lb.) UPS Capacity (kVA) 6 8 10 12 Weight (lb.) 307 507 507 507 B) Minimum clearance required for ventilation Right side 1.2" (30 mm) (not required when sidecars are used) Left side 1.2" (30 mm) (not required when sidecars are used) Back side 3.9" (100 mm) Top side 23.5" (600 mm) C)

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: iii List of Tables Table 1.1 Power Specifications..................................................................... 1-12 Table 1.2 UPS Module Information............................................................... 1-12 Table 1.3 Rating of Conductor and Fuses .................................................... 1-12 Table 1.4 Detail of Specifications.................................................................. 1-13 Table 2.1 D-Sub 25 Pin connector.............................

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 1-11 Description of UPS parts, referred to in Figure 1.5 to Figure 1.8: 1. Relay PCB RYER-A board Signal I/F on RYER-A board : (Figure 1.8): - (7) RS232C communication connector - (8) D-Sub 25 Pin connector - (9) External contact signal terminal block 2. Maintenance Bypass Switch (52CS) (FOR SERVICE PERSONNEL ONLY) This switch is used to transfer the load from inverter power to external power for maintenance purposes. Do not operate

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-12 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.4.2 PROCEDUR FOR INTERNAL BATTERY CONNECTION Procedures for battery connection are as follows. Please note, these procedures must be performed after the external cables are connected. For procedures for external cable connection, please refer to “3.3 PROCEDURE FOR CABLE CONNECTIONS”. 1. Remove the straps, which hold the batteries. 2. As shown in the left figure, when shi

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 1-12 1.4 SPECIFICATIONS The UPS name plate displays the rated kVA as well as nominal voltages and currents. The name plate is located on the interior side of the UPS front door. TABLE 1.1 Power Specifications Rated output Power Input voltage 1 ph 3 wire or 2 ph 3 wire Output voltage 1 ph 3 wire or 2 ph 3 wire 6kVA / 4.2kW 8kVA / 5.6kW 10kVA / 7.0kW 12kVA / 8.4kW 240/120, 208/120 240/120, 208/120 240/120, 208/120 240/120, 208/120 240/120, 208/120 240/120, 208/120 240/120, 208/120 240/120, 208/120 TABLE 1.2 UPS

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-14 MITSUBISHI ELECTRIC 7011A SERIES UPS 4. If turning off all power to the critical load is desired, open the AC Input Circuit Breaker (User supplied.). CAUTION: In bypass mode, all UPS power terminals are still alive. Lethal voltages are present. De-energize all external sources of AC and DC power before handling UPS. D) UPS Shutdown Procedure 1. If a total UPS module (inverter and rectifier) shutdown is required, press the "STOP" button on the front panel. 2. Then STOP Mode window will appear on the LCD. 3. Press the “STOP” and “ENTER” buttons simultaneous

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 2-5 B) Normal Mode FIGURE 2.4 Tree Diagram of LCD Display (Normal Mode) BATTERY 216V CHARGE Measure OUT1 120V 60.0Hz OUT2 120V 60.0Hz OUT1 100A 100% 12.0kW 100% OUT2 100A 100% 12.0kW 100% INPUT 240V 60.0Hz M enu Top P a ge CLEAR key MEASURE ¥ LOG ¥ SILENCE ¥ SETUP M anual(UP/DOWN Key) or Auto Scroll O utput Voltage OUT VOLTAGE ADJ 0.0 -> +2.0% B attery Check BATTERY CHECK - CHECKING - Time MONTH/DATE /‘YEAR 10 /

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 2-1 2.0 OPERATOR CONTROLS AND INDICATORS The 7011A Series operator controls and indicators are located as follows: Maintenance bypass switch and contactors : Inside the unit UPS status indicators : Door exterior FIGURE 2.1 Operation/Display Panel (Front panel) MEASURE ¥ LOG ¥ SILENCE ¥ SETUP INV.OP UPS BYP.OP BAT.OP A LARM  £ MENU ENTER CLEAR STOP START 

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 7-1 MITSUBISHI ELECTRIC 7011A SERIES UPS 7.0 WARRANTY & OUT OF WARRANTY SERVICE The Mitsubishi Electric UPS Systems Group Service Department has many Authorized Service Centers placed strategically throughout the US, Canada and Latin America. For both in warranty and out of warranty service, please contact Mitsubishi Electric Automation, Inc. at (847) 478-2643. To register your UPS for warranty purposes, please complete the warranty registration fo

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 1-7 FIGURE 1.3 Single Line Diagram - Battery Operation The UPS is equipped with an internal rotary type Maintenance Bypass Switch (MBS) that can be used to divert utility power to the load during maintenance sessions. Figure 1.4 illustrates the power path when the MBS is in the BYPASS mode. FIGURE 1.4 Single Line Diagram - UPS on Maintenance Bypass Operation. UPS Cabinet FB BATTERY CB2 Static Transfer Switch Power Flow N ot in Use FO CONVERTER INVERTER Output AC input CB User supplied MCCB Maintenance Bypass Switch CB1 F I 52CS UPS Cabinet F

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-10 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.4 INSTALLATION PROCEDURE FOR BATTERY Installation procedures of the batteries are shown on the next page. Please refer to the following when installing and maintaining batteries: 1. Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized personnel away from batteries. 2. When installing or replacing batteries, install or replace with the same number and type per Table 3.4 TABL

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 1-9 FIGURE 1.6 UPS Parts Location(8,10 and 12kVA) Main PCB UPFR-L 1.Relay I/F PCB RYER-A UPS module FRONT VIEW Converter & Inverte r Battery Cooling fan Display PCB DPAU-63 I/O Module 3.Module Connection terminal 2.Maintenance bypass transfer switch 52CS

• MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 2-4 2.2 LCD DISPLAY Followings are tree diagrams of LCD display. A) Top Page FIGURE 2.3 Tree Diagram of LCD display (Top Page) See Fig 2.4 See Fig 2.5 See Fig 2.6 See Fig 2.7 OUT: 120V 60.0Hz BATTERY: FAILURE PRESS MENU->LOG EVENT CODE 806 OVE

• MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: vii CAUTION PRECAUTIONS FOR INSTALLATION PRECAUTIONS FOR INSTALLATIONPRECAUTIONS FOR INSTALLATION PRECAUTIONS FOR INSTALLATION • Do not block the intake/exhaust ports. Install the UPS at least 4” (10cm) away from walls, etc. -If the intake/exhaust ports are bl

• MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-7 FIGURE 3.6 Field Wire Connection (208V – 120V WYE, 2 phase, 3wire) NOTE: Proper phase rotation must be observed when connecting input wires to L1 and L2. If code 803 occurs See next page. Ground Ground 208V-120V Y L N L External Battery Cabin

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 2-8 2.4 D-SUB 25 PIN CONNECTOR Uses dry contact on/off to express NORMAL, FAULT, ON BATTERY, BATTERY LOW, ON BYPASS, ON INVERTER status. Connections not to exceed NEC Class 2. TABLE 2.1 D-Sub 25 Pin connector Pin No. Signal I/O Pin No. Signal I/O 1 Failure A Contact Output 14 Output 2 Failure A Contact com Output 15 Output 3 Output 16 Output 4 Battery Operation A Contact Output 17 Output 5 Battery Operation com Output 18 Output 6 Output 19 Output 7 Battery Low Voltage A Contact Output 20 Output 8 Battery Low Voltage A Contact com Output 21 Output 9 Bypass Operation A Conta

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 6-1 MITSUBISHI ELECTRIC 7011A SERIES UPS 6.0 FAULT CODES This section covers the fault codes, their description and required action. At time of error : A) Verify and record the occurrence of the alarm. Note fault code on the LCD. Contact Mitsubishi Electric Automation, Inc. at 1-800-887-7830. B) If the External AC Input Circuit Breaker (MCCB) is in the trip state, depress the toggle to reset the breaker before re-closing.

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 2-9 2.5 EXTERNAL SIGNAL TERMINAL BLOCK (Option) The UPS is equipped with a series of input/output terminals for the external annunciation of alarms and the remote access of certain UPS functions. A functional description of the input/output port is presented below. Layout of terminals is shown in Figure 2.10. Connections not to exceed NEC Class 2. FIGURE 2.11 External Signal Terminal Block UPS 12 10 11 8 9 7 6 5 4 3 2 1 9 – 10: BATTERY TEMPERATURE 5 – 6: RE-STARTUP 7 – 8: RE-SHUTDOWN 3 – 4: REMOTE EPO 1 –2: FAILURE (User supplied dry contact) RYER

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 1-5 1.3 OVERVIEW The UPS provides two power paths between the utility source and the critical load. Figure 1.1 shows the path for normal operation, with the load powered from the inverter. Figure 1.2 shows the path for bypass operation, with the load supplied through the static bypass line. FIGURE 1.1 Single Line Diagram - Normal Operation. Load powered by inverter. During normal operation, the path through the inverter is used to power the load. Referring to Figure 1.1: Input AC power is converted to DC by the Converter. DC power is utilized to charge the U

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-4 MITSUBISHI ELECTRIC 7011A SERIES UPS TABLE 3.2 Recommended Cable Size and Torque Requirements UPS Capacity Input Side *1 Output Side *1 (kVA) Cable Size Torque (in. lbs) Cable Size Torque (in. lbs) 6kVA (208V) 10 AWG * 2 or larger 80 in. lbs 10 AWG * 2 or larger 80 in. lbs 8kVA (208V) 8 AWG * 2 or larger 80 in. lbs 8 AWG * 2 or larger 80 in. lbs 10kVA (208V) 6 AWG * 2 or larger 80 in. lbs 6 AWG * 2 or larger 80 in. lbs 12kVA (208V) 6 AWG * 2 or la

• MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 3-15 MITSUBISHI ELECTRIC 7011A SERIES UPS 3.6 MAINTENANCE BYPASS SET-UP PROCEDURES (For Service Personnel Only) A) Transfer of load from inverter to maintenance bypass 1. Press “MENU” button and then select “BYPASS_OP.” and press ENTER button. 2. Press “ “ or “ “ until the display sho

• Mitsubishi 7011A SERIES, MITSUBISHI ELECTRIC 7011A SERIES UPS MITSUBISHI ELECTRIC 7011A SERIES UPS OWNERS / TECHNICAL MANUAL Page Number: 2-11 B) Input Contacts(for remote access of UPS) External contacts are provided by the user of the UPS system. Terminal voltage at the UPS is 24Vdc. Provide external dry contact accordingly. CAUTION: Do not apply voltage to remote access input terminals. Damage to UPS may result. Refer to Figure 2.12 for typical wiring configuration. Although this figure applies to the RE-STARTUP terminals, the same wiring arrangement is used for RE-EPO; RE- SHUTDOWN, Battery temperature. FIGUR

Related Products and Documents (UPS):

Comparable Devices:

Similar Resources:

• GE 700 VA (16 pages) GE Digital Energy Firmware Update Installation Guide Digital Energy™ Uninterruptible Power Supply On-line VH Series UPS 700 - 1000 - 1500 - 2000 - 3000 VA GE Consumer & Industrial SA General Electric Company CH – 6595 Riazzino (Locarno) Switzerland T +41 (0)91 / 850 51 51 F +41 (0)91 / 850 51 44 www.gedigitalenergy.com …

• Steren NB-605 (2 pages) 534No Break 600 VA V3.0NB-6050318AManual de InstruccionesLea cuidadosamente este instructivo para evitar cualquier mal funcionamiento.La información que se muestra en este manual sirve únicamente como referencia sobre el producto. 1. Conecte el no-break a un tomacorriente.2. Conecte sus equipos de cómputo en los contactos polarizados.3. Presione el b …

• Phasak KRYPTOS Series (28 pages) SERIE KRYPTOS [ES]PH 9478LEA AL MENOS ESTOSiga estrictamente todas las advertencias e instrucciones de estemanual.Antes de instalar esta unidad, lea todas las instruccionesatentamente.No utilice este SAI antes de leer atentamente toda la informaciónde seguridad y las instrucciones de uso.PELO MENOS LEIA ISTOSiga estritamente todas as advertências e instru� …

• CyberPower PR750LCDRTXL2U (2 pages) The LCD display indicates a variety of UPS operational conditions. All descriptions apply when the UPS is plugged into the AC outlet and turned on or when the UPS is on battery. 10. Serial Port I Serial port allows connection and communication between the UPS and the computer. 11. Serial Port II Serial Port II relays information to equipm …

• HPE G2 R5000 (3 pages) MF877-00 Page 1 Template Revision A HPE instructions for this template are available at MF877-01 Product End-of-Life Disassembly Instructions Product Category: Other Products Marketing Name / Model [List multiple models if applicable.] HPE G2 R5000/6000 3U WW ERM Purpose: The docu …

• HP T2200 XR (53 pages) Artisan Technology Group is your source for quality new and certied-used/pre-owned equipment• FAST SHIPPING AND DELIVERY• TENS OF THOUSANDS OF IN-STOCK ITEMS• EQUIPMENT DEMOS• HUNDREDS OF MANUFACTURERS SUPPORTED• LEASING/MONTHLY RENTALS• ITAR CERTIFIED SECURE ASSET SOLUTIONSSERVICE CENTER REPAIRSExperienced engineers and techni …

Comments, Questions and Opinions: