Manualios.com

Beam RST200 Installation & User Manual

Beam RST200 Manual Online:

3.1, 2402 votes
Beam RST200 User Manual
Beam RST200 User Guide
Beam RST200 Online Manual

Text of Beam RST200 User Guide:

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 37 RS232 Specification The RST200 is provided with two RS232 serial ports for log and data connection. Both are 9-pin D-type (female) sockets, wired DCE for connection to a standard PC with a 1:1 cable. Physical Connection The pin-out of both connectors is described in the following table: Pin Signal Direction Description 1 DCD RST ¼ PC Data Carrier Detect 2 RXD RST ¼ PC Received Data 3 TXD PC ¼ RST Transmitted Data 4 DTR PC ¼ RST Date Terminal Ready 5 GND Signal Ground (Common) 6 DSR RST ¼ PC Data Set Ready (CTS and DCD) 7 RTS PC ¼ RST Request to Send 8 CTS PC » RST

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 32 Assuring Quality of Iridium Service Iridium is committed to providing users around the world consistent, reliable, quality voice and data access all day every day. The Iridium satellite system is monitored for call performance from numerous locations 24 hours a day, 7 days a week in order to achieve this. Iridium continually strives to provide high quality voice and data communication links for its subscribers. However, there are conditions that c

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 7 About BEAM Communications Beam Communications, is an authorised manufacturer of Iridium Satellite products. Beam develops subscriber products that utilise the Iridium satellite network of Low Earth Orbit satellites, known as LEOs. The Iridium network is extensively used around the world by commercial enterprises and defence agencies. Beam products address the needs of individuals, communities, government agencies and the corporate sector, providing voice and data access without the need for traditional wire-line or mobile

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 6 Welcome Welcome to the Beam RST200, the intelligent remote satellite modem. This Installation and User manual contains all the information you need to configure the Beam RST200 and discover the advantages of Beam Communications and Iridium Network technology. Conventions in this Manual Warnings, cautions and notes appear throughout this manual. They are represented by following conventions. Warning: This symbol and associa

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 17 Mounting methods The mounting brackets allow two mounting methods: drop-in (inside corner) mount and flush (outside corner) mount. Figure 3 - Mounting methods To install the RST200 unit : 1. Attach the two (2) mounting brackets securely to a suitable structure making sure the space between the brackets is wide enough to smoothly slot in the RST200.

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 33 The following table should be used as a guide in selecting the appropriate cabling, if you have not already purchased a certified cable from Beam. RF Interference . All wireless devices, including satellite telephones, are susceptible to RF (radio frequency) interference from other electronic devices. This problem is especially evident when numerous antennas and broadcasting devices are located within close proximity to each other. A good example would be onboard a ship. It is important that certain considerations be taken into account for best performance when an Iridium system

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 5 Safety Information Note: Read the following information before installing and using the BEAM RST200. Your RST200 is a low power radio transmitter and receiver. When it is ON, it receives and sends out radio frequency (RF) signals. The design of your RST200 system complies with international safety standards. Refer to the appropriate section of the RST200 User Manual for additional relevant safety information. Warning: Do not open equipment. There are no user-serviceable parts inside. If a DC power supply is to be used,

  • RST200 INSTALLATION & USER MANUAL 22 Installing the Antenna Planning the Antenna Installation The fixed site antenna system consists of a fixed mount antenna and a coaxial cable system that connects the antenna to the RST200. The antenna system is suitable for both marine and terrestrial applications and is designed to meet Iridium System performance requir

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 30 Mobile / Transport Installations Heavy Machinery Installations Installing Antenna Cables When you install the cables, follow these guidelines: • Route and restrain cables to prevent them from vibrating or moving under normal conditions, which could result in damage to the antenna, Beam terminal, or the coaxial cable connections. • Wherever the cables contact structures, protect the cables from chafing or abrasion. When you must bend a cable, avoid kinking it, and ensure that each bend radius follows the cable supplier’s recommended limits. • Use coaxial

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 25 Remote Configuration The Supervisor Menu items are available for remote configuration via a combination of the Iridium Short Burst Data and or SMS services. Refer to your Service Provider on how to register for this service. To configure your RST remotely you will need to know its Phone Number, Supervisor PIN and the International Mobile Equipment Identifier or IMEI number. Multiple configuration commands may be sent in one SMS. The Supervisor PIN is only required once at the start. Once the PIN has been entered the top of hierarchy for each subsequent command in the message i

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 16 Installing RST200 This chapter explains how to install the RST200 and the Iridium fixed-mast antenna. Warning: Make sure the RST200 is switched off before you install the cables. If you do not, the RST200 may be damaged. Note: Before you install the RST200, determine if the unit is preconfigured or needs customer configuration. Mounting the RST200 The RST200 comes with two (2) standard right angle mounting brackets that allow mounting for mobile and fixed positioning. Note: To ensure sturdy mount attachment: 1. Mount the RST200 on a clean, even surface. 2. Clean the mount surface of the RST200. 3.

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 40 Q You can’t make international calls. A Have you included the relevant codes? Press and hold the (+) key to display the international dialling prefix (+), and then enter the appropriate country code, followed by the phone number. Q Your PIN is blocked A Enter the PIN unblocking key (PUK1) or contact your service provider Q Your PIN2 is locked. A Enter the PIN2 unblocking key (PUK2) or contact our service provider. Q Your SIM card won’t work. A Is the card inserted the

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 34 and 45 meters (50 to 150 feet, respectively) of an operating INMARSAT mini-M or Standard-C terminal, will likely experience degraded performance. Other sources of RF interference such as Globalstar units, radar devices and broadcast stations can provide interference for Iridium units, but usually are not encountered as frequently as INMARSAT terminals. Symptoms of RF Interference Symptoms of RF interference often resemble those that arise when an Iridium phone is being operated with an obstructed view of the sky. Some of these symptoms include; erratic or no signal strength indication, dropped calls or warbled or otherwise distort

  • RST200 INSTALLATION & USER MANUAL 8 What is the RST200? The RST200 is a Remote Satellite Modem designed to provide a reliable and cost effective voice and or data service connection when a wired connection is not available. It does this by providing a standard modem interface to the Iridium network — a satellite-based, wireless communications network that e

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 28 In-vehicle Hands free Kit (Optional) The RST200 is capable of supporting the Beam RST973 optional In-vehicle hands- free kit to provide in vehicle hands-free operation within a vehicle. The In-vehicle hands free kit is supplied with and Intelligent Handset as well as a full in-vehicle integration. The in-vehicle integration supports ringer alert and other specific vehicle features if required such as horn alert and radio mute. Installation of In-vehicle Hands-free The RST973 optional in-vehicle hands free kit is simply connected to the RJ45 socket of th

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 15 PIN Details The RST has a number of different PIN’s, each one to perform or limit certain functions. The table below identifies these PINS, their function and a place for you to note the setting for your unit. PIN Name Function Indication that entry of PIN is required Your PIN SIM PIN Supplied by your Service Provider Enables calls to be made if SIM is locked Signal light flashes Red PUK Supplied by your Service Provider Unlocks a locked SIM card Signal light flashes Red User PIN Supplied with this manual Allows access to user menu of RST200 via log port Enter PIN on console 9876 Default Su

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 23 Installation Options The fixed site antenna system consists of a fixed mount antenna and a coaxial cable system that connects the antenna to the Satellite Terminal Equipment. Ensure that the antenna cable being used does not exceed 3DB loss. The antenna system is suitable for marine, vehicle and fixed applications and is designed to meet Iridium System performance requirements when installed according to the instructions in this guide. The following figure shows typical Installations: Vehicle Antenna Installation The ideal position for any vehicle- mounted application is to c

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 24 Data Terminal settings for auto-answering an incoming data call. To initialize the RST200 to receive an incoming data call, start a Terminal Program (such as HyperTerminal) with the following settings: 19200* bps, 8, N, 1, Flow Control = None. Then to enable the RST200 to auto answer, type the following AT commands to the RST200: ATS0=1 (This turns on auto-answer) AT+IPR=x (where x baud of Terminal Program, according to 1 = 600 bps 2 = 1200 bps 3 = 2400 bps 4 = 4800 bps

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 21 Connecting the Antenna Cable 1. Plug the antenna cable into the antenna jack located on the rear panel of the RST200. 2. Ensure that the specified cable being used does not exceed the Iridium 3DB maximum loss rating to ensure maximum performance of the terminal. Refer to your Service Provider for full details or to purchase and approved cable.

  • RST200 INSTALLATION & USER MANUAL 35 Recommended Operating Distances: Inmarsat Mini-M Recommended Distance Between an Iridium Unit and an Active Inmarsat Mini-M Terminal Antenna • Main Lobe = directly in front and in line with the Inmarsat terminal antenna: 225 feet (68 meters) • Side Lobe = directly to the side and in line with the Inmarsat terminal antenna: 100 f

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 11 Signal Strength The Signal Strength LED gives an indication of how strong the signal is from the Iridium network at your location. This LED displays different colours to indicate the strength of the RF (Radio Frequency) signal and different on/off conditions to indicate the terminal status. Indictor colour Signal strength Flashing RST200 is registering with the network – please wait Green Strong Orange Acceptable Red No signal, problem with installation or no access The Signal Strength LED reading will vary in status in relation to th

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 3 Contents CONTENTS........................................................................................................................................................... 3 SAFETY INFORMATION.................................................................................................................................... 5 WELCOME............................................................................................................................................................ 6 Conventions in this Manual ...............................................................................................

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 19 Connecting the Intelligent Handset or In-Vehicle Hands-free 1. Plug the Intelligent handset or the in-vehicle hands free unit into the Handset Connector of the RST200 2. Ensure the power is turned off when connecting the device 3. If the handset should ever lock up at any time, then power cycling the terminal will reset the peripheral device.

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 4 ASSURING QUALITY OF IRIDIUM SERVICE ............................................................................................. 32 O BSTRUCTIONS . ............................................................................................................................................... 32 C ABLING ............................................................................................................................................................ 32 RF I NTERFERENCE . ........

  • RST200 INSTALLATION & USER MANUAL 10 The RST200 Status Indicators The status indicators are located on the front panel of the RST200. The LED lights on the front panel show the RST200 status. Note: The LED lights blink in different combinations to indicate transmission status. Display Status Indicators Power When the RST200 powers up, the Power indica

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 38 RS232 Port LBT Data Port Data Logging Port DCD DCD = DTR RXD RXD TXD TXD DTR DTR DSR DSR = DTR RTS RTS CTS CTS = RTS RI RI not connected RS232 Port Electrical Parameters The LBT “Comm” Port and Log Ports conform to the RS232 interface specification with the following parameters, however the Log Port communicates only at 9600 : Parameter Specification Communication Rate 220 to 115,200 Baud Protocol 1 start bit, 8 data bits, no parity, 1 stop bit, a

  • RST200 INSTALLATION & USER MANUAL 13 Getting Started What is a SIM Card? A SIM Card (Subscriber Identity Module) is a small smart card that carries your identity for accessing the network and receiving calls. It functions as the digital memory of the RST200 and also stores your personal information, including received SMS messages. SIM Card Protectio

  • Beam RST200, RST200 INSTALLATION & USER MANUAL 36 Specification Summary Electrical Power 11-32V DC 2.5A Plug-pack (if provided) 90-250VAC 50/60Hz input Power Consumption (Average) 12Volt 24Volt Standby Mode 0.125A 0.065A Talk/Transmit Mode 0.600A 0.185A Modem Type Hayes Compatible Speed 2400 bps EMC Compliance C-Tick and A-Tick, CE mark Environmental Operating Temperature Range 0°C to +55°C ambient Operating Humidity Range <85% RH non-condensing Storage temperature -30C to +70C Weight 2.5 kg Dimensions 290x225x60m

Related Products and Documents (Modem):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 AG Neovo C-19P Operation & user’s manual ag-neovo/c-19p-Y42.pdf 23 Feb 2024 7 6.36 Mb
2 Brother PocketJet 6 Plus Print Engine Manual  brother/pocketjet-6-plus-print-engine-CVI.pdf 07 Nov 2023 100 12.25 Mb
3 Yamaha M7CL Quick start manual yamaha/m7cl-CK1.pdf 17 May 2023 14 3.96 Mb
4 Panasonic DMRES35 Operating instructions manual panasonic/dmres35-2K8.pdf 29 Feb 2024 80 4.66 Mb
5 Hitachi RAC-10CX Instruction manual hitachi/rac-10cx-196.pdf 10 Apr 2023 42 1.19 Mb
6 Valcom V1030M Manual  valcom/v1030m-ZNI.pdf 23 Jan 2023 5 0.05 Mb

Similar Resources:

  • Cisco

    ASR 5000 Series

    (163 pages)
    Cisco ASR 5000 Series Thresholding Configuration Guide Version 12.2 Last Updated April 30, 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-25552-02 …
  • NETGEAR

    WGR614v2 - 54 Mbps Wireless Router

    (2 pages)
    Installation GuideFollow these quick steps to install your router.Before you begin, locate the broadband Internet configuration settingsfrom your cable company. You can also consult the Install Assistant on theGearBox™ CD for 54 Mbps Wireless Router.11Connect the Routera. Turn off your computer and cable or DSL modem.b. Disconnect the Ethernet cable from y …
  • TP-Link

    Archer VR2800

    (2 pages)
    Quick Installation GuideVR2800AC2800 Wireless MU-MIMO VDSL/ADSL Modem Router1.Connect the Hardware2.Configure the Modem Router SSIDs (network names) and Wireless Password are on the Wi-Fi Info Card.Method 2: Via TP-Link Tether App1. Download the TP-Link Tether app.or2. Connect your smartphone to the router.3. Launch the Tether app and select Archer VR2800. …
  • Nortel

    1000

    (50 pages)
    Nortel Application Gateway 1000Nortel Application Gateway Release 6.1Hardware Installation GuideInstallationDocument Number: NN42360-300Document Release: Standard 01.04Date: January 2007Year Publish FCC TMCopyright © 2007 Nortel Networks. All rights reserved.Produced in CanadaThe information in this document is subject to change without notice. The statemen …
  • Black Box

    ME0005A-10BT

    (31 pages)
    CUSTOMERSUPPORTINFORMATIONOrder toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018Web site: www.blackbox.com • E-mail: [email protected] 2001ME0005A-10BT2 …
  • Trio

    ER450

    (8 pages)
    Quick Start Guide - ER450 Data Radio 1QuicQuicQuicQuicQuick Stark Stark Stark Stark Start Guidet Guidet Guidet Guidet GuideER450 DaER450 DaER450 DaER450 DaER450 Data Rta Rta Rta Rta Radioadioadioadioadio1.0 IntroductionWelcome to the Quick Start Guide for the ER450 DataRadio. This guide provides step-by-step instructions, withsimple explanations to get you u …

Comments, Questions and Opinions: