Atec AL170 Operation & User’s Manual
|
Atec AL170, Please check the below particulars before you contact the service center to notify an abnormality of the monitor. The window doesn’t show anything Is the monitor power cord inserted? Please connect the power cord correctly to the concent. Is the power turned off? Please press the power button. Is the power turned on and the power pilot lamp blinking amber? The monitor is in the power saving mode. Please therefore move the mouse or press any key on the keyboard. Is the message ‘Out Of Range’ shown? If a power indicating lamp of amber color blinks, press any key to go back to previous mode. As it passes over the frequency limit of horizon (31.5-80 kHz) and verticality (60-75
Atec AL170, Adjusting the OSD Menu 13 HORIZONTAL : Adjusts the horizontal position of the display. VERTICAL : Adjusts the vertical position of the display. CLOCK : Increases or decreases the number of pixel to adjust the horizontal size. PHASE : Adjusts the focus and clarity of the display. EXIT : Exits POSITION menu. POSITION OSD POSITION : Adjusts the position of the OSD window. OSD LANGUAGE : Adjusts the language of the OSD window. (ENGLISH, DEUTSCH, FRANAIS, ESPAÑOL, ITALIANO) OSD TIME : Adjusts the waiting time the OSD fades away. Can adjust the waiting time up to 60 seconds the OSD fades away if you do not inp
Atec AL170, Before Use English ● This user manual contains proprietary information that is protected by copyright. All rights are reserved. No part of this user manual may be reproduced, photocopied, transcribed, translated or transmitted in whatsoever from without the prior permission of the manufacturer. ● The size and appearance of this monitor may be changed for improvement without notice. ● Damage caused by using the unauthorized components or disregard of the information and cautions in this user manual is not covered by the warranty service. ● If you have problem with your monitor, please check TroubleShooting in this user manual before asking for help se
Atec AL170, CE Conformity Notice The Product herewith complies with requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and carries the ‘CE’ mark accordingly. Confirms to the following hamonized European standards have been applied: EMC : EN 55022 Class B : 1998 EN 55024 : (EN 61000-4-2 : 1995, A1 : 1998, EN61000-4-3 : 1996, EN 61000-4-4: 1995, EN61000-4-5 : 1995, EN61000-4-4 : 1996, EN61000-4-8 : 1993 and EN61000-4-11 : 1994) EN61000-3-3 : 1995, A1 : 98, A2 : 98 EN61000-3-3 : 1995 FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is sub
English ● Don’t plug the power adapter into a non-grounding power outlet. ▶ Matters that demand special attention are divided into ‘Warning’ and ‘Caution’, and are detailed a follows. ● Never touch the power plug with wet hands. An electric shock accident may occur. ● Don’t plug with other electrical cords into one power outlet. An electric shock or fire accident may occur
16 The details of product specification can be changed without notice to improve the product. Factory-specified Mode 1 2 3 4 5 6 7 8 9 10 11 12 13 Factory-specified Mode Horizontal Vertical Frequency(kHz) Frequency(kHz) VGA VGA VGA VGA VGA SVGA SVGA SVGA XGA XGA XGA SXGA SXGA 640 x 350 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 1024 x
Atec AL170, English Unpacking After opening the box, make sure the following items are provided with the monitor. If you find that any of these items is missing or appears damaged, contact your dealer immediately. The actual monitor and accessories may appear differently from those shown on the above figure Note Diskette (Monitor Driver) Power Cord User Manual DC Adapter Audio Cable VGA Signal Cable Monitor
Atec AL170, English ● Turn off the monitor and disconnect all cables from the monitor before moving the monitor. ● Be careful with the shock when moving the monitor. ● Place the monitor on a stable and secure surface. Fall or displacement of the monitor may cause an injury. ● Don’t scratch or jolt the monitor surface. Damage or failure of the panel may be caused. ● Often take a rest to protect your eyes when you work for a long time. ● Take hold of the monitor with both hands setting the panel forward. If the monitor is dropped, contact the service center to check i
Atec AL170, 2.2 Installing the Monitor Driver Under Linux 10 Linux You’d make xf86config file to run X-Window. Your monitor is surely and easily configured with this file. This file will be made as running xf86config. 1 Press Enter in the first and second window after running xf86config file. 2 In third window, we come up with the mouse setting window. 3 Configure it as opt for user system. 4 Next will be the screen for selecting Keyboard. 5 Configure it as opt for user system. 6 First, configure a horizontal frequency. Please r
Atec AL170, 2 1.2 Installing and Removing the Support Installing the Support Removing the Support Lay a soft cloth and place the monitor on it with the screen facing downwards. (Take caution not to cause scratches to the LCD display.) 1 Push in the support in the direction of the arrow. (Make sure that the ‘latches’ are fixed to the LCD.) 2 While pressing the ‘latches’ on both sides, push the support in the direction of the arrow and remove it. 3 Latch Support Support Latch ❶ ❷
Atec AL170, 6 Set of headphones External Speakers LINE OUT AUDIO IN AUDIO OUT AUDIO Cable Stereo Camcorder AUDIO(RCA) Cable 3 Connecting Audio Devices Connect the audio cable to the AUDIO IN on the monitor and the LINE OUT on the computer or connect the audio cable (RCA) cable to the AUDIO IN on the monitor and the stereo on the camcorder/TV and connect a set of headphones or external speakers to the AUDIO OUT.
Atec AL170, Installing the Monitor Driver 9 Windows XP Turn on the computer and the monitor. 1 Insert the monitor driver diskette into the FDD on the computer. 2 In the Display Properties window, click the Setting tab and then select Advanced. 5 Select the Monitor tab and click Properties. 6 Select the Driver tab, click Update Driver and then click Next. 7 Welcome to the Hardware Update Wizard Select Install a list or specific location(Advanced) option and click Next. 8 Please choose your search and installation option Select Don’t search. I will choose the driver to install option and click Next. 9 Please wait while the wizard installs the software. Now, start in
Atec AL170, 3.2 Exclusive ANALOG Monitor OSD Menus 12 Main Menu Software Version BRIGHTNESS : Controls the brightness of the display. CONTRAST : Adjusts the level of difference between light and dark areas of the display. EXIT : Exits BRIGHTNESS/CONTRAST menu. BRIGHTNESS/CONTRAST Screen Resolution Screen Frequency The exclusive ANALOG monitor can use only ANALOG signals as input signals. RED : Changes the value of red. GREEN : Changes the value of green. BLUE : Changes the value of blue. EXIT : Exits COLOR menu. COLOR Controls the color( Red, Green, Blue) of the display. Controls the brightness and contrast of the display.
Atec AL170, Installing the Monitor 3 This section identifies the name of each component of the monitor and briefly describes the function of each component. MENU Button Displays or Exits the OSD menu window. POWER Button Turns the monitor on and off. SELECT Button Selects the OSD menu item and the submenu item to be adjusted in the OSD menu window and save the modified value at any selected item. (If you press continuously every two times, the input source will be switched.) RIGHT Button Increases the value of the selected item. (Increases the volume without pressing the MENU Button.) LEFT Button Decreases the value of the selected item
Atec AL170, English ● Grasp the power plug at the base to remove it from the wall, and pull firmly but gently. If you yank at the cord, the wire may be broken, causing ignition or heat generation. ● Pull the power cord out when the monitor is not used for a long time, or while you are away. A dust covering may cause an electric shock, electric leakage, or fire by heat generation, ignition, and insulation degradation. ● Select a cool, dry area and protect your monitor from extremes in temperature, humidity, du
Atec AL170, 2.1 Installing the Monitor Driver Under Windows 7 This section shows how to install the monitor driver under Windows or Linux by using the monitor driver diskette provided. To install the monitor driver, please refer to your OS in this section. Turn on the computer and the monitor. 1 Insert the monitor driver diskette into the FDD on the computer. 2 Installing the Monitor Driver In the Display Properties window, click the Setting tab and then select Advanced. 5 Select the Monitor tab and click Properties. 6 Click the Start button on
English ● Don’t block or obstruct the air-flow holes of the monitor. A fire or damage of the monitor may be caused due to an increase in internal temperature. ● Don’t spill liquids such as chemicals, water on the monitor. A fire or electric shock accident may be caused. ● Never disassemble and repair the monitor but trained repair engineers. A fire or ele
Atec AL170, CONTENTS English 1.1 Features …………………………………………………………… 1 1.2 Installing and Removing the Support ……………………………… 2 Installing the Support ……………………………………………………… 2 Removing the Support …………………………………………………… 2 1.3 Monitor Overview ………………………………………………… 3 Front Side …………………………………………………………… 3 Rear Side …………………………………………………………… 4 1
8 Windows 2000 Turn on the computer and the monitor. 1 Insert the monitor driver diskette into the FDD on the computer. 2 Click the Start button on the Windows display and select Control Panel. 3 Double click the Display icon in the Control Panel window. 4 In the Display Properties window, click the Setting tab and then select Advanced. 5 Select the Monitor tab and click Propertie
Atec AL170, 3.1 Selecting and Adjusting the OSD (On Screen Display) Menu Adjusting the OSD Menu 11 You can select the OSD menu in the OSD window by using all the control buttons under the display. To change the current settings or adjust it to what you prefer, please follow these steps. Selecting and Adjusting the OSD Menu Press the MENU button to open the OSD menu window. 1 Press the UP/DOWN button to move the desired main menu item. 2 The main menu item you moved is highlighted, press the SELECT button. 3 Press the UP/DOWN button to move the desired submenu item. 4 The submenu item you moved is highlighted, press the SELECT
Atec AL170, Installing the Monitor 5 Turn off the monitor, computer and other peripheral devices before connecting the monitor and peripheral devices. 1 2 1.4 Connecting the Peripheral Devices DC-IN Jack DC Adapter Power Cord ANALOG Connector ANALOG Connector VGA Cable Connecting the power Plug into the power outlet at 220V or 110V. (The voltage is set automatically.) Connecting the computer Connect the ANALOG connector on the computer.
Samsung HB890 Monitor Specifications
HB890 |
NEC MultiSync E750 Monitor Operation & user’s manual
MultiSync E750 |
ViewSonic VA720 - 17" LCD Monitor Monitor Operation & user’s manual
VA720 - 17" LCD Monitor |
Elo TouchSystems 1229L(WWW) Monitor Operation & user’s manual
1229L(WWW) |
AOC 916VWA Monitor Operation & user’s manual
916VWA |
Vuzix iWear VR920 Monitor Software manual
iWear VR920 |
Samson 6A Monitor Owner's manual
6A |
Mitsubishi Electric LDT42IV Monitor Operation & user’s manual
LDT42IV |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Ikegami | ML Series | Operation & user’s manual | ikegami/ml-series-4PC.pdf | 20 Mar 2024 | 36 | |
2 | Clarion | CZ500E | Owner's manual & installation manual | clarion/cz500e-J6E.pdf | 13 Jan 2024 | 29 | 2.63 Mb |
3 | Philips | 29PT8805 | Specification sheet | philips/29pt8805-YRV.pdf | 25 Jul 2022 | 3 | 0.68 Mb |
4 | York | DHM42CMB21S | Service manual | york/dhm42cmb21s-75V.pdf | 16 Jan 2023 | 83 | |
5 | Linear | VB-2 | Installation instructions | linear/vb-2-5ZN.pdf | 22 Apr 2023 | 1 | |
6 | Konig | CMP-UPS650VAL | Manual | konig/cmp-ups650val-38R.pdf | 26 Dec 2023 | 41 |
Philips
19” CDT Color Monitor 109B7 1 Service Service Service Horizontal Frequency 30-92 kHz Table of contents …
109B7(90 pages) |
Sanyo
INSTRUCTION MANUALColor Video MonitorVMC-8618VMC-8620CONTENTSINFORMATION TO USER . . . . . . . . . . . . . . . . . . . . . . 1PRECAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3PARTS NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5BASIC OPER …
VMC-8620(12 pages) |
NEC
Audio BaseUSER'S MANUALAccuSync ®To learn about other special offers, register online at www.necmitsubishi.com/ productregistrationAudioBase 9/29/00, 11:26 AM1
…
AccuSync Display Solutions AccuSync(16 pages) |
Pixio
The color and the appearance may differ depending on the product, and the specifications are subject to change without priornotice to improve the performance.The contents of this manual are subject to change without notice to improve quality.Copyright © 2019 Pixio USA Inc. I Pixio is a registered trademark of Pixio USA Inc. I All Rights Reserved.Use or repr …
PXC243(22 pages) |
Sceptre
MQC Series P1 X322 Series User Guide PACKAGE CONTENTS SCEPTRE Display x 1 Display Base x 1 Base Screws x (ST4x12) x 3 Circular Metal Plate x 1 Black Plastic Ring x 1 Power Cord x 1 (Attached) Warranty Card x 1 Display Remote Control x 1 User Guide x 1 (Complete manual available online at sceptre.com) ATTACHING & REMOVING THE BASE 1. To install or …
X322 Series(8 pages) |
Acer
TABLE OF CONTENTSSpecial notes on LCD monitors..................................................1Information for your safety and comfort..................................2Unpacking...................................................................................5Attaching/Removing the base....................................................6Screen position …
P216H(23 pages) |
Black & Decker Sander SteamXpress S600 SeriesPDF User Guide (@224L2B), Black & Decker SteamXpress S600 Series Sander (29.09.2023) SteamXpress S600 Series, 6 |
Nortel Intercom System BSTNortel Intercom System Operation & user’s manual (File: nortel-bst-operation-user-s-manual-7, Wednesday 25-10-2023) BST, 7 |
Accu-Chek Blood Glucose Meter MobileAccu-Chek Blood Glucose Meter Mobile Operation & user’s manual Mobile, 243 |
Sony Camcorder DCR-HC30 MarketingDCR-HC30 Marketing Service manual - 5KR1RX DCR-HC30 Marketing, 73 |
Star Broiler STAR-MAX OCB30Broiler Installation and operation instructions manual (Star STAR-MAX OCB30) STAR-MAX OCB30, 40 |
Reer Work Light KidsLight Creative 5274KidsLight Creative 5274 (Work Light ePDF User Guide, #784396) KidsLight Creative 5274, 2 |
Auto Meter Battery Charger AC-90Operator's manual for Auto Meter AC-90 Battery Charger AC-90, 8 |
Roth Power Tool i-press mini MAP2LROTHGuide: Roth i-press mini MAP2LROTH (DQ3KD3, Upd.Mon 10.2023) i-press mini MAP2LROTH, 78 |
D&K Laminator Masterpiece 550Masterpiece 550 (Laminator ePDF User Manual, #692341) Masterpiece 550, 12 |
Simplicity Lawn Mower 990198PDF Manual (@Z35H5U), Simplicity 990198 Lawn Mower (01.02.2024) 990198, 2 |
PYLE Audio Automobile Accessories Camera PLCM20Camera PLCM20 Specifications - SGEK37 Camera PLCM20, 1 |
LG Washer WT4970CWLG Washer Owner's manual (File: lg-wt4970cw-owner-s-manual-76, Tue 10.2023) WT4970CW, 76 |