Manualios.com

Datron guardian II series Operator's Manual

Datron guardian II series Manual Online:

4.55, 585 votes
Datron guardian II series User Manual
Datron guardian II series User Guide
Datron guardian II series Online Manual

Text of Datron guardian II series User Guide:

  • Datron guardian II series, BAUD 4800, 9600, 19200, 38400 BAUD Rate CNTRLS Enable/Disables Turn radio controls on or off. 2. Channel Submenu This submenu allows you to add new channels or make changes to existing channel settings. Channels can be selectively locked, preventing you from making changes. If you select a locked channel, CHANNEL LOCKED/ACCESS DENIED is displayed. Adding a New Channel The following is an example of programming a new channel into an empty slot. This same process is used to modify existing channels. Note: The new channel is assigned to whatever channel position the

  • Datron guardian II series, 7: FIRE FEATURES OPTION This chapter assumes a knowledge of the standard operation of the Guardian portable radio detailed in the preceding chapters of this manual. Introduction The Fire Feature option is designed for users in a high-risk fire environment or a similar special setting. This option adds the following features to the Guardian portable radio. • Tone picklist • P25 Talkgroup picklist • P25 UnitID picklist • Event bank for setting up an additional 3 zones of 16 channels each. Also known

  • Datron guardian II series, 8: TROUBLESHOOTING The following table of symptoms, possible causes, and suggested corrective actions may be helpful. Consult authorized personnel for further guidance. Symptom Probable Cause Corrective Action Radio does not turn on No power source Supply power source Cannot talk with other users in plain mode Radios programmed for different frequencies, squelch tones, talk- group IDs Program radios to same frequency settings Background noise or other conversations heard Other users on channel or improper squelch tone setting Select another channel or program squelch tones to eliminate interference Error message on d

  • Datron guardian II series, Global Submenu 1. Select ROPTNS , PROGRM, GLOBAL and press < ENT > . Pressing the down scroll key will go to through the following pages: 2. Choose from the following settings: Setting Value Description LITE (Backlight) Bright, dim or off Enables, disables, and varies the intensity of the LCD’s backlight. LT DLY (Backlight delay) 1 to 9 seconds Sets the time delay for the LCD and keypad backlighting. LTONRX On or off Backlight goes on when signal received.

  • Datron guardian II series, Options The Guardian II portable radio supports add-on software options for solutions to communications requirements such as P-25 Trunking and Encryption. Optional enhancements are discussed in the final chapters of this manual. The Guardian II Portable is covered by the limited warranty (see warranty statement) Factory Support For warranty service, contact: Technical Support Services Group Datron World Communications Division 3030 Enterprise Court Vista, CA 92081 Phone: (760) 597-1500 E-mail: [email protected]. Before calling have the following information: • Radio model number, serial

  • Datron guardian II series, • Analog or digital • Various squelch types • Encryption key • Power output level • 12-character alphanumeric channel tag (name) Zones Zones provide a way of rapidly switching groups of channels. Each zone can contain up to 16 channels. If the 3 position collar switch set for Zone Select, the radio provides easy access to 48 channels by using the collar switch and the channel select knob. Up to 64 zones can be accessed from the radio keypad or programmable soft keys and displayed in the standard radio. Channels can be mapped to the channel select knob within each zone usin

  • MODE Analog Analog settings displayed. B/W 12.5 KHz or 25 KHz (default) Bandwidth. RX 136 MHz to 174 MHz Receive frequency. NONE No receive squelch. NOISE (default) SQ= If you choose noise, adjust the squelch level by highlighting SQ and scrolling left and right. DCS CODE= If you choose DCS, highlight CODE and enter the D

  • Datron guardian II series, Function Description Scan Sets scan mode to On, Priority, or Off. Position A: Scan, Priority scan, or off Position B: Scan, Priority scan, or off Position C: All scan modes off Monitor (includes squelch adjust) Provides monitor and carrier squelch adjust functions. Position A: Squelch adjust mode (carrier squelch only) Position B: Monitor on Position C: Programmed squelch mode (monitor off) Zone Select Selects Zone A, B or C. Position A: First zone assigned in current bank Position B: Second zone assigned in current bank Position C: Third zone a

  • Datron guardian II series, Analog/Digital Tone Pick List Tone pick lists are created in the PC Programmer. They are selected by accessing the main menu. Up to 32 transmit tones (CTCSS, DCS) and 32 digital NAC codes can be programmed into the radio. If one of these tones or codes is selected, the programmed tag name replaces the existing channel name. The use of a tone picklist provides a permanent change to the channel. To access these tones, the following options exist. For all of these, press the # key for a short duration (press and

  • Datron guardian II series, 3: OPERATING THE RADIO The Guardian II operates with most of its features already programmed into the radio. Request a list of the functions that are assigned to the buttons and switch on your radio. Quick Start Before proceeding, the radio must be set up using the Guardian PC Programmer. If necessary, refer to Chapter 2, Controls and Indicators. 1. Battery Install a charged battery. 2. Antenna Install the correct antenna for the frequency being used. Do not operate the radio without an antenna. 3. Power-

  • Transmitting Press the PTT button and speak normally about four inches from the microphone. Release the PTT button when finished speaking. Do not hold the PTT longer than necessary after talking. Channels programmed for receive-only sound an alert tone, display RX ONLY , and do not transmit. Your radio may be setup with the Transmit Inhibit feature. This feature locks

  • Datron guardian II series, 1: INTRODUCTION Guardian II Portable Radio The Guardian II series portable radios are crafted with advanced electronics, software and materials incorporated into a rugged, professional design offering years of reliable service. The radios provide operation in analog or digital, wideband or narrowband modes, and are APCO Project-25 compatible. The Guardian II is available in three separate models (pictured below) allowing the radio to be customized to end user requirements. Numerous combinations of options, features and channel settings are possible using the Guardian PC Programmer.

  • Datron guardian II series, Encryption Menu This menu is for modifying the encryption settings setup in the PC Programmer. 1. From the main menu, scroll to ROPTNS, ENCRYPT and press < ENT > . 2. Use the keypad to enter the password for this radio. 3. Press < ENT > . 4. Choose from the following settings: Setting Value KEYSEL (Key select) Choose the active key for the channel ZEROIZE (Zeroize keys) Zeroize key for channel or all keys DF KEY (Default key) Activates the channel's default key 4.

  • Datron guardian II series, Global Data Check GLOBAL DATA to clone the auxiliary button settings, toggle switch settings, transmit timeout settings, transmit inhibit settings, scan settings, and priority scan settings. The following data is not cloned: • Keypad lock • Keypad disable • Scan Mode • Priority Scan Mode • Passwords • Unit ID and other Unit Identifiers All Zones Check ALL ZONES to clone all banks, all zones, and all channels. This includes data from the Event bank. Event Clone 1. Check EVENT CLONE to clone a single zone or zones into the target radio’s Event bank without affecting the remaining zones of the target radio. An interim screen is displayed

  • Datron guardian II series, Adding a Shadow Channel To add a shadow channel to a primary channel, perform the steps in the following sequence: 1. Determine the next available shadow channel (press *1, *2, etc. until an error tone is heard indicating the channel is empty). 2. Select PROGRM , CHANEL while on the desired primary channel. 3. Press *x to get to the desired new shadow channel. 4. Scroll through the settings and change as necessary. Settings that can be changed are: • Channel type: analog or digital • Bandwidth • Key assignment • Squelch (CTCSS, DCS, P25 NAC, P25 Talkgroup) All other settings must

  • Datron guardian II series, Emergency Mode To activate Emergency mode, press and hold the Emergency button (must be programmed as Emergency) for about ½ second. The emergency mode remains active indefinitely until deactivated. To deactivate, press and hold the button again, or turn the radio off and on. Emergency channels are setup using the keypad ( refer to “Global Submenu”). If the Emergency setting ( EMG) is left empty, the current channel serves as the emergency channel. In P25 mode, the emergency bit is set. Since analog modes have no similar function, the radio performs an open-

  • Datron guardian II series, 6: ENCRYPTION OPTION This chapter assumes knowledge of the standard operations of the Guardian II portable radios detailed in the preceding chapters of this manual. Introduction When operating in the digital mode the radio is capable of secure communications by means of software-based encryption and is fully compatible with any radio using P25 digital encryption standards AES or DES-OFB. When the radio is operating in the secure mode, the transmission of all tone squelch signals is disabled. The radio displays a key icon indicating t

  • Datron guardian II series, P25 Unit ID Call Picklist If a call is received with a matching UnitID in the lookup table, the name is displayed. Otherwise, the actual UnitID is displayed. It can be programmed by the PC Programmer or by accessing the radio’s main menu. This picklist cannot be cloned. To access an existing P25 UnitID picklist: 1. Turn the channel knob to the desired P25 digital channel. 2. Press and hold the # key to display the list. Do one of the following. • To make a UnitID call to someone who is not programmed into the radio, scroll to the first selection, ENTER # . Press <ENT> an

  • Datron guardian II series, 8. Press PTT on the KVL to initiate the key transfer. When the transfer is successful, SUCCESS KEY DATA UPDATED displays. If unsuccessful, FAILURE KEY DATA NOT UPDATED displays. 9. Press <ENT> to return to the key tag or the key ID displays. 10. Press <ESC> or turn the radio off and on to resume normal operation. Note: To stop the transfer at any time, press <ESC> . For more information, consult the KVL instruction manual.

  • Datron guardian II series, 3. Press < ESC > to resume radio operation. 4. To enter a new valid password, power the radio off and on. When menus are disabled, the radio displays MENU DISABLE . Consult authorized personnel for guidance. Entering Data Enter alphanumeric and numeric data using the keypad. Each Key has a number and alphanumeric letters associated with it. For Example when entering data and pressing the 2 key the display will show the following: A,B,C,2,a,b,c. . Scan Menu The scan menu allows you to enable and disable the normal scanning and priority scanning and to select the type or mode of scanning to use. 1. Access the main menu. Scroll to highlight ROPTNS and pres

  • Datron guardian II series, a  around a channel type means it is included in a scan list Modulation type icons: AW = analog wideband AN = analog narrowband DG = digital a  around the modulation type means some form of selective squelch is active for the channel (NAS, CTCSS or DCS) Other icons: TX = transmit channel in scan mode RX = receive channel in scan mode TA = talkaround ∩∩∩ = repeater    = encrypted U = unit ID call mode = Battery Gauge = Signal Strength Indicator Navigation Buttons These four buttons perform actions determined by what appears on the display. The MENU button lets you access the intern

  • Datron guardian II series, • Entering a repeater code for access to a repeater. • Accessing a repeater with a phone patch to dial a phone number. • Accessing remote weather stations using DTMF tones A, B, C, and D by pressing the corresponding navigation keys. To access while in any analog mode, press the PTT button and the desired key.

  • Select Menu The select menu allows you to designate a different zone or bank to a button or switch on the radio. You can also select an individual call and enable or disable Talkaround. 1. Access the main menu. Highlight ROPTNS and press RNT. 2. Scroll to highlight SELECT and press < ENT >. 3. Choose from the following settings: Setti

  • Internal Speaker and Microphone The internal speaker is active when external audio accessories are not used. The internal microphone is active when you press the PTT button. Emergency Button The red emergency button on top of the radio is typically used for P25 Emergency operation but can be programmed by the PC Programmer for any of the following functions. Ask your radio

  • Datron guardian II series, 6. Scroll down to RX , and set it to 154.600000 MHz. 7. Scroll down to the next screen. Leave RXSQMD at CTCSS . 8. 8. Scroll down and to Tone and Press ENT. Use the up arrow until the desired to is found. 8. Scroll to TX and set it to 154.6000000 MHz. 9. Scroll to TXMSQMD and set it to CTCSS . Set TON to 67.0 XZ .

Related Products and Documents (Portable Radio):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 FUNAI F313CB Owner's manual funai/f313cb-6G2.pdf 12 Sep 2023 32 0.3 Mb
2 Aqua Lung Regulator Owner's manual aqua-lung/regulator-SE2.pdf 16 Aug 2023 26
3 Asko T721 Operation & user’s manual asko/t721-55D.pdf 16 Aug 2022 24 0.27 Mb
4 Drolet COMPAK EPA EXEMPT 45109A Instructions manual drolet/compak-epa-exempt-45109a-4C7.pdf 01 Mar 2023 19 0.48 Mb
5 Yaesu FTDX5000 - SOFTWARE UPDATE AND VERSION IDENTIFICATION Software update yaesu/ftdx5000-software-update-and-version-identification-EDE.pdf 01 Jul 2022 10 0.56 Mb
6 TTI TCB-R2000 Service manual tti/tcb-r2000-56K.pdf 24 Jul 2023 5

Similar Resources:

  • Motorola

    GP68

    (44 pages)
    Manual Number: 502-450123278 Bernhardt Street • Hayward, CA. 94545 Phone: (510) 887-1950 • Fax: (510) 887-4011Internet: [email protected] and OperationManualSmarTrunk II TMLogic BoardforMotorola GP68Portable RadiosSmarTrunk Systems, Inc. • ST-865M3Motorola P/N PMLN4066A …
  • Vertex Standard

    VX-410 Series

    (41 pages)
    IntroductionThis manual provides technical information necessary for servicing the VX-410/-420 series FM Transceiver.Servicing this equipment requires expertise in handling surface-mount chip components. Attempts by non-qualifiedpersons to service this equipment may result in permanent damage not covered by the warranty, and may be illegal insome countries.T …
  • Kenwood

    NEXEDGE NX-300S

    (101 pages)
    SERVICE MANUALThis product complies with the RoHS directive for the European market.This product uses Lead Free solder.K2 version© 2011-10 PRINTED IN JA PANB51-8992-00 (Y) 330NX-300(S)UHF DIGITAL TRANSCEIVERDoes not come with antenna. Antenna is available as an option.GENERAL .................................................................. 2SYSTEM SET-UP …
  • GE

    Superadio

    (6 pages)
    Re-typed in HTML format, remaining as faithful as possible to the original.MODEL7-2880AFM/AMPORTABLE RADIOFILE TAB 7CAUTION: THIS MANUAL IS DESIGNED FOR USE BY QUALIFIED ELECTRONIC TECHNICIANS ONLY. CONSUMERUSERS ARE URGED TO CONTACT QUALIFIED FACTORY AUTHORIZED SERVICE FACILITIES FOR REPAIRS.FEATURESTuned RF on FM and AM improves reception38" swivel wh …
  • Motorola

    ASTRO XTS 1500

    (66 pages)
    ASTRO® XTS™ 1500 Digital Portable RadioModel IUser Guide6804113J52MOTOROLA, the Stylized M Logo, ASTRO, and CommPort are registered in the U.S. Patent & Trademark Office. All other product or service names are the property of their respective owners.P25 radios contain technology patented by Digital Voice Systems, Inc.© Motorola, Inc. 2002. All Rights …
  • SOUNDMASTER

    TR-40

    (17 pages)
    OPERATING INSTRUCTIONSBEDIENUNGSANLEITUNGMODE D'EMPLOIGEBRUIKSAANWIJZINGNAUDOJIMO INSTRUKCIJAKASUTUSJUHENDMANUAL D'INSTRUCCIONES TR - 402-BAND PORTABLE RADIO2-BAND TRAGBARES RADIORADIO PORTATIF À 2 BANDES2-BAND RADIONE� …

Comments, Questions and Opinions: