Manualios.com

Force Computers PENT/CPCI-721 Installation Manual

Force Computers PENT/CPCI-721 Manual Online:

4.25, 791 votes
Force Computers PENT/CPCI-721 User Manual
Force Computers PENT/CPCI-721 User Guide
Force Computers PENT/CPCI-721 Online Manual

Text of Force Computers PENT/CPCI-721 User Guide:

  • Force Computers PENT/CPCI-721, Features Introduction 1 - 4 PENT/CPCI-721 Interfaces Both the PENT/CPCI-721 and the I/O-721 provide several interfaces which are described in the following subsections. PENT/CPCI-721 The interfaces include: • 10/100 BaseT Ethernet, routable to a front panel or CompactPCI connector via switch-selection • One parallel interface LPT, IEEE 1284 compatible and with ECP and EPP (1.7/1.9) support (Extended Capabilities Port), available on CompactPCI connector only for the PENT/CPCI-721 • PS/2 keyboard and mouse controller, 8042 compatibl

  • Force Computers PENT/CPCI-721, BIOS BIOS Messages PENT/CPCI-721 4 - 11 Fixed Disk 0 Failure Fixed Disk 1 Failure Fixed Disk Controller Failure Fixed disk is not working or not configured prop- erly. Check to see if fixed disk is attached properly. Run Setup to be sure the fixed-disk type is correctly identified. Fixed Disk 0...3 Identi- fied Autotyping identified specified fixed disk. None Incorrect Drive A type - run SETUP Incorrect Drive B type - run SETUP Type of floppy drive not correctly identified in Setup Check for correct floppy drive in setup. Keyboard controller error The keyboard controller failed test.

  • Force Computers PENT/CPCI-721, Boot Selection Menu BIOS 4 - 4 PENT/CPCI-721 Boot Selection Menu BIOS automatically starts during power-up or reset. Press <Esc> while boot-up screen is displayed to continue with the POST screen until the end of POST. Then the boot selection menu is dis- played. In the boot menu, you will find the following options: 1. Override existing boot sequence (for this boot only) by selecting another boot device from boot-order list If the specified device does not load the operating system, BIOS reverts to previous boot sequence. 2. Enter Setup 3. Press <Esc> to return to the POST screen and continue with previous boot sequence

  • xii PENT/CPCI-721 Table 21 Switch and Interrupt Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Table 22 Watchdog Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 Table 23 Watchdog Retrigger Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 Tabl

  • Force Computers PENT/CPCI-721, Board Installation Installation 2 - 24 PENT/CPCI-721 Figure 14: PCI Interconnection between PENT/CPCI-721 and I/O-721 ❶ 1 PMC module (user option) I/O-721 in 2nd slot MEM-720L PENT/CPCI-721 in 1st slot MEM-720U VGA-IO720-4 PCItoP- CI PENT/CPCI-721 ❶ Cutout for CPU heat sink on base board

  • Force Computers PENT/CPCI-721, On-Board Connectors Controls, Indicators, and Connectors 3 - 14 PENT/CPCI-721 Figure 28: 8-bit SCSI Connector Pinout VGA-IO720-4 As a factory option the VGA-IO720-4 graphics controller based on the Chips&Tech 69030 graphics device is installed on the I/O-721 board providing the following graphics modes: • 1600x1200 dots resolution and max. 65536 colors at max. 60 Hz verti- cal refresh • 1280x1024 dots resolution and max. 16.777.216 colors at max. 75 Hz vertical refresh • 1024x768 dot

  • Force Computers PENT/CPCI-721, Installation Board Installation PENT/CPCI-721 2 - 23 Removing the I/O-721 from the PENT/CPCI-721 In order to uninstall the I/O-721 from the PENT/CPCI-721, proceed as follows: 1. Remove four screws at location I1, I2, I3, and I4 (see figure below) Figure 12: Mounting Points of the I/O-721 on the PENT/CPCI-721 2. Disconnect I/O board locks from PENT/CPCI-721locks (see figure below): Figure 13: Connecting Pins between Front Panel Handles 3. Disconnect I/O board from base board (see ❶ in the figure below): I1 PENT/CPCI-721 front-panel I4 I2 I3 I/O-721 Connecting pins PENT/CPCI-721

  • Force Computers PENT/CPCI-721, Features SCSI BIOS 5 - 4 PENT/CPCI-721 Note: • In case of display problems press <F5> to toggle the display between color and monochrome. This feature may not work on all monitors. • The default settings are appropriate for most applications, so there usually is no need to change the settings. If you have to change the settings of the advanced configuration options listed below, you should ensure that you thoroughly understand the consequences of the change before actually doing so. Selectable Host Adapter SCSI ID SCSI IDs range from 0…7 if the respective dev

  • Force Computers PENT/CPCI-721, Boot Configuration BIOS 4 - 8 PENT/CPCI-721 Depending on the messages displayed, there are other keyboard inputs resulting in calls to special BIOS set-up programs, including, for exam- ple, <Ctrl>+<A> to enter the SCSI BIOS for the dual-segment variant. If the BIOS or an Option ROM (e.g. of an add-on card) requests key- board input, you are prompted to enter the information. POST contin- ues from there with the regular POST screen. Note: Whenever POST detects a non-fatal error, BIOS displays the errors. It then displays a message asking you to choose between boot continuation or error correction via Setup.

  • Force Computers PENT/CPCI-721, Maps and Registers PENT/CPCI-720/2/3 Registers PENT/CPCI-721 6 - 7 I 2 C Register The I 2 C register is used for data transfer settings on the I 2 C bus and pro- vides access to the program-readable vintage registers for the base board, the I/O board, the lower and upper memory modules, the VGA- IO720 as well as the registers controlling the configuration of the tem- perature sensors. Table 16: I 2 C Register Address: 0108 16 Bit Value Description Access Settings 0DIR Direction bit for I 2 C data r/w =0 Data

  • Force Computers PENT/CPCI-721, PENT/CPCI-721 xxv Erweiterung Beachten Sie den Gesamtstromverbrauch aller installierter Kompo- nenten (siehe technische Daten der entsprechenden Komponente). Vergewissern Sie sich, daß jeder individuelle Ausgangsstrom jedes Stromverbrauchers innerhalb der zulässigen Grenzwerte liegt (siehe technische Daten des entsprechenden Verbrauchers). Benutzen Sie bei der Erweiterung ausschließlich von Force Computers empfohlene Komponenten und Systemteile. Ansonsten sind Sie für die Auswirkungen auf EMV und die möglicherwe

  • xx PENT/CPCI-721 Installation Electrostatic discharge and incorrect board installation and uninstal- lation can damage circuits or shorten their life. Therefore: • Before installing or uninstalling the board, check the “Require- ments” section on page 2-3. • Before touching integrated circuits, make sure that you are work- ing in an ESD-safe environment. • When plugging the bo

  • Force Computers PENT/CPCI-721, Boot Configuration BIOS 4 - 6 PENT/CPCI-721 Boot Configuration The boot configuration options in Setup let you select the order of the devices from which BIOS attempts to boot the operating system. During POST, BIOS tries the next one on the list if it is unsuccessful at booting from one device. Each device listed represents the first of a group of devices if more than one device of this group is installed on the system. For example, if there is more than one hard disk drive, the displayed entry represents the first of these drives as specified in the boot configuratio

  • Force Computers PENT/CPCI-721, PENT/CPCI-720/2/3 Registers Maps and Registers 6 - 16 PENT/CPCI-721 NMI Status Register The NMI Status register indicates the device which caused an NMI and enables clearing all of its status bits via a write access to the register. Table 25: NMI Status Register Address: 010C 16 Bit Value Description Access Settings 0 TEMP Indicates whether tempera- ture sensor 0 below the CPU caused an NMI since the last clearance of the status bits via a write access to the reg- ister. r =0 (default) No NMI has been caused. =1 Temperature sen- sor 0 caused an NMI. 1 WDOG In

  • Force Computers PENT/CPCI-721, Installation Hardware Upgrades and Accessories PENT/CPCI-721 2 - 19 IDE Devices It is possible to connect up to four IDE devices to the PENT/CPCI-721: • As a factory option, a 16 MByte flash disk can be installed to the pri- mary IDE port. • A HD accessory kit can be installed to the primary IDE port via the on-board connector. Before connecting IDE devices to the primary or secondary IDE port: 1. Check for IDE devices already connected to the IDE interface 2. Decide which IDE device should be master and which should be slave 3. Check for switch settings and change configuration if necessary

  • PENT/CPCI-720/2/3 Registers Maps and Registers 6 - 6 PENT/CPCI-721 PENT/CPCI-720/2/3 Registers The following section gives an overview of the board-specific registers. Lock/Unlock Register The Lock/Unlock register enables or disables read and write access to the PENT/CPCI-720/2/3 specific registers. Table 15: Lock/Unlock Register Address: 010E 16 Bit Value Description Ac

  • Force Computers PENT/CPCI-721, SCSI BIOS Features PENT/CPCI-721 5 - 3 Features The SCSI BIOS must be enabled if you want the system to boot from a SCSI hard disk drive connected to the adapter. If the devices on the SCSI bus are controlled by device drivers and therefore do not need a BIOS, you can disable the SCSI BIOS to free about 16 KBytes of memory. This also shortens the boot time by up to 60 seconds. The SCSI BIOS provides two functions to support user configuration: • Listing of the actually used SCSI IDs and correlated LUNs • Setup options to adapt the CPU board and its SCSI configuration to the user’s needs. The default configuration

  • Force Computers PENT/CPCI-721, Requirements Installation 2 - 4 PENT/CPCI-721 Environmental Requirements The environmental values must be tested and proven in the used sys- tem configuration. These conditions refer to the surroundings of the board within the user environment. Note: Operating temperatures refer to the temperature of the air cir- culating around the board and not to the actual component tempera- ture. To ensure that the operating conditions are met, forced air cooling is required within the chassis environment. Caution If the standard PENT/CPCI-720/HD-AccKit is installed, the operation temperature of the PENT/CPCI-721 is limited by the

  • Force Computers PENT/CPCI-721, Features SCSI BIOS 5 - 6 PENT/CPCI-721 Send Start Unit Command Enabling the adapter to send the SCSI start unit command to the SCSI device (SCSI command 1B) reduces the load on a system’s power sup- ply by allowing the adapter to turn on SCSI devices one by one when the system boots. Otherwise, all SCSI devices are turned on at the same time. Before you enable this option for a device, check the device docu- mentation to make sure the device supports the command. On most devices, you must also change a switch or jumper se

Related Products and Documents (PCI Card):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Mad Catz 5772 Operation & user’s manual mad-catz/5772-6I4.pdf 14 Mar 2024 1
2 Beachcomber 160 Owner's manual beachcomber/160-4LD.pdf 27 Jun 2022 32
3 Casablanca Areto 54120 Owner's manual casablanca/areto-54120-9D3.pdf 01 Jul 2023 2
4 Creative D5xm Manual  creative/d5xm-N36.pdf 29 Apr 2023 1 0.51 Mb
5 Cloer 6269 Instruction manual cloer/6269-2AM.pdf 18 Dec 2023 16
6 Samsung DMB58AHC Operation & user’s manual samsung/dmb58ahc-83D.pdf 24 Feb 2023 32 5.16 Mb

Similar Resources:

  • Zoom

    4414F

    (2 pages)
    Model 4414F with standard PCI bracketZoomWireless-G PCIWi-Fi® LAN AdapterSupports 802.11g and 802.11b■Plugs into the PCI slot of a Windows computer (XP, 2000, Me, 98SE)■Works in all 802.11g, 802.11b, and mixed networks■High Security with WPA (WiFi® Protected Access), WPA 2, and WEP■Model 4414F has a standard mounting bracket for desktop systems.Bra …
  • Askey

    WLL6190D25

    (20 pages)
    Introduction: Askey WLL6190D25 802.11g / 802.11n WLAN PCI-E Mini Card User's GuideBefore you beginThings you should knowWLL6190D25 network Before you beginObtain the following information from your network administrator (if you are a home user, obtain this information from the person that installed your wireless access point):● Network names (SSID …
  • Multitech

    ISI4604-PCI

    (2 pages)
    1 of 2ISI4604-PCIProduct UpdatePN 82097300, Rev. A2/5/99The new IntelligentSerialInterface card, model ISI4604-PCI, is a four-port version of the eight-port ISI4608 product documentedin your owners manual. All of the product specifications, installation instructions, and technical information applies except for thefanout cable.Figure 1. The ISI4604-PCI …
  • Lindy

    51095

    (4 pages)
    _________________________________________________________________________ PCI 2 Port FireWire + USB 2.0 4 Port USB2.0 User Manual English LINDY No. 51095 www.LINDY.com © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (Jan. 2008) The USB Po …
  • Edimax

    EW-7728In

    (1 pages)
    www.edimax.comEDIMAX TECHNOLOGY CO., LTD.IEEE802.11n Wireless 32-bit PCI CardFeatures• Complies with 802.11n, 802.11g and 802.11b standards.• Provides further coverage, less dead spot and higher throughput(up to 300Mbps) with MIMO technology.• Supports WMM, WMM-PS and WMM-SA (IEEE 802.11e QoS standards).• Supports 64/128-bit WEP, WPA (TKIP with IEEE …
  • SOC technologies

    PCIe-I-8K

    (11 pages)
    PCIe-I-8K PCIe Card User Guide © 2018 SOC Technologies Inc. …

Comments, Questions and Opinions: