Cisco CIAG-GW-IP10 Operation & User’s Manual

Text of Cisco CIAG-GW-IP10 User Guide:

• Cisco CIAG-GW-IP10, CHAPTER 4-1 Cisco Physical Access Gateway User Guide OL-20932-01 4 Connecting a Cisco Input Module Overview The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to ten input devices. Each connection can be configured as supervised or unsupervised. A supervised connection is a four- state connection to determine if the connection is (1) short (2) is open (3)normal state or (4) alarm state. An unsupervised input indicates only normal or a

• Cisco CIAG-GW-IP10, 4-2 Cisco Physical Access Gateway User Guide OL-20932-01 Chapter 4 Connecting a Cisco Input Module Package Contents The optional Cisco Input Module is connected to a Cisco Physical Access Gateway or Cisco Reader Module using a CAN connection to provide connections for additional input devices, as, as shown in Figure 4-2. Figure 4-2 Cisco Reader Module connected to the Cisco Physical Access Gateway Package Contents Each Cisco Input Module includes the following: • 20 resistors (1K) for input supervision • 2 mounting brackets, with 4 screws for each bracket • Regulatory compliance and safety information •

• Cisco CIAG-GW-IP10, 4-3 Cisco Physical Access Gateway User Guide OL-20932-01 Chapter 4 Connecting a Cisco Input Module Physical Overview and Port Description • Connector plugs: Physical Overview and Port Description Each Cisco Input Module includes 10 ports for connecting additional input devices. as shown in Figure 4-3. Figure 4-3 Cisco Input Module Ports and Connectors Type Quantity 3 Pin 1 2 Pin 13 1 2 5 6 4 3 187043

• 4-4 Cisco Physical Access Gateway User Guide OL-20932-01 Chapter 4 Connecting a Cisco Input Module Physical Overview and Port Description Figure 4-4 Cisco Input Module Ports and Connectors: Top View The following items are shown in Figure 4-3 and Figure 4-4: 4 5 6 1 2 3 187039 Type Description 1 Power Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC extern

• Cisco CIAG-GW-IP10, 4-5 Cisco Physical Access Gateway User Guide OL-20932-01 Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module Status LEDs Each input port includes a status LED that indicates the following information: Installing the Cisco Input Module Install a Cisco Input Module is provide additional input connections for a Cisco Reader Module or Gateway Before You Begin Verify the following: • Verify that the module has access to a power source. See Power Options and Requirements, page 1-10 for more information. • Verify that you have the necessary mounting brackets

• Cisco CIAG-GW-IP10, 4-6 Cisco Physical Access Gateway User Guide OL-20932-01 Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module Step 2 Connect the module to the DC power source: a. Insert a two-pin connector plug into the DC power port (Figure 4-5) b. Connect the Voltage In (VIN) and ground (GND) wires. See Power Options and Requirements, page 1-10 for more information. Figure 4-5 Power Connections for the Input and Output Modules The following items are shown in Figure 4-5: Step 3 Connect the module to the CAN bus: a. Insert a three-pin connector plug into the CAN1 port,

• 4-7 Cisco Physical Access Gateway User Guide OL-20932-01 Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module Figure 4-6 CAN Connections: Input and Output Modules The following items are shown in Figure 4-6: Figure 4-7 CAN Bus Wiring Step 4 Connect input devices to the module: a. Insert two-pin connector plugs into the input ports. b. (Optional, fo

• Cisco CIAG-GW-IP10, 4-8 Cisco Physical Access Gateway User Guide OL-20932-01 Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module Figure 4-8 Input Connections: Cisco Physical Access Gateway and Reader Module c. Connect the wires from the input devices. Note Each of the input connections can be configured as supervised or unsupervised. The tamper (TM) and power fail (PF) inputs can be configured as additional unsupervised ports. A supervised input supports four states: normal, alarm, open and short. An unsupervised input indicates only normal or alarm. Step 5 See the Cisco Physical Access Manager User Guide for information to configure the module p

Related Products and Documents (I/O Systems):

Comparable Devices:

Similar Resources:

• ADLINK Technology NuDAM-6063 (2 pages) 6000 Series Discrete Input/Output Modules Part No: 50-12026-200 The Optimal Choice for Harsh Environment -6063 Relay Output and Isolated Input Module 1. Introduction NuDAM-6063 provides eight form A relay output channels. It can control high power devices without external circuits. The isolation guarantees the industrial safety. Features  4 ch …

• GE AF-650 GP (212 pages) GE Consumer & IndustrialElectrical DistributionAF-650 GPTMGeneral Purpose DriveDesign GuideThe instructions do not purport to cover all details or variations in equipment nor to provide for every possiblecontingency to be met in connection with installation, operation or maintenance. Should further information bedesired or should particular problems aris …

• Kilsen KAL760 (16 pages) KAL760 Addressable Input Module Installation Sheet EN ES IT PT FR NL CS NO PL HU 1 EN: Installation instructions Description The KAL760 provides a remote input to an addressable fire detection system. The input signal is constantly monitored and its status communicated to the fire panel. The module has five …

• Allen-Bradley MicroLogix 1200 RTD/Resistance (22 pages) Publication 1762-IN014B-EN-P - July 2013Installation InstructionsMicroLogix 1200 RTD/Resistance Input ModuleCatalog Number 1762-IR4Topic PageModule Overview 2Description 2Module Installation 3System Assembly 4Mounting 4Field Wiring Connections 7I/O Memory Mapping 15Specifications 19North American Hazardous Location Approval 22Additional Resources 23 …

• National Instruments 6738 (16 pages) CALIBRATION PROCEDURENI 6738/6739Analog Output Devices and Modules with NI-DAQmxThis document contains the verification and adjustment procedures for the National Instruments PCIe-6738 and PXIe-6738/6739 analog output devices and modules. For more information about calibration solutions, visit ni.com/calibration.ContentsSoftware.............................. …

• Contec N Series (4 pages) Ver.1.02 COM-4PDHN-USB 1 N Series for USB RS-422A/485 4ch Isolated Serial I/O Unit COM-4PDHN-USB * Specifications, color and design of the products are subject to change without notice. This product is an USB2.0-compliant product designed for extending RS-422A/485 compatible serial communication functionality on your PC. This product supports …

Comments, Questions and Opinions: