Manualios.com

Integral Audio IASS-T Installation Manual

Integral Audio IASS-T Manual Online:

4.1, 2968 votes
Integral Audio IASS-T User Manual
Integral Audio IASS-T User Guide
Integral Audio IASS-T Online Manual

Text of Integral Audio IASS-T User Guide:

  • Integral Audio IASS-T, D. SOUNDSTAGE 12 30. SPEAKER WIRING (OVERVIEW) The front channels of the ARC amplier drive the front tweeter and midrange/midwoofer in parallel. The rear channels drive the subwoofer. The factory HU/Amp continues to drive the rear ll speakers. In Standard 6 speaker vehicles, the signal wiring harness feeds the door midrange and midwoofer via the X9331 T- harness. In HiFi/HK equipped vehicles, a separate connection is made to the factory wiring downstream of the HiFi/HK amplier. There are separate wires for the tweeters in all vehicles. 31. AMPLIFIER TO SPEAKER OUTPUT CONNECT

  • Integral Audio IASS-T, F. SETTINGS 23 84. SET GONG VOLUME TO MIN [NAV & MINI CONNECTED] If your speedo has a large screen at the center, you have Nav or MINI Connected. From the music control section, select TONE -> VOLUME SET- TINGS -> GONG. Set the gong volume to the lowest level (Re- turn to the tone controls menu and set BASS and TREBLE to at. (THESE ARE CRITICAL) 85. SET FRONT CHANNEL GAIN We recommend setting the front channel gains to minimum as a starting point. This will give you the highest signal to noise ratio. This controls the total system max volume. In 99% of cases this

  • Integral Audio IASS-T, BEFORE YOU BEGIN 2 • Read this Guide completely BEFORE you begin. • Disconnect the battery negative terminal while working on the vehicle. • DO NOT PLACE THE KEY FOB in the vehicle with the battery connected and the seat airbag wiring disconnected. Doing so will set off the airbag light, and must be reset by your dealer. • ALWAYS check behind panels and components before drilling, cutting, or screwing into any part of a vehicle. • This guide covers several different vehicle models and options. Some steps only apply to certain inst

  • Integral Audio IASS-T, WHAT’S IN THE BOX 3 SOUNDSTAGE I. SOUNDSTAGE SPEAKER PACKAGE 1. IASS-T 1” Silk Dome Tweeter (Pair) 2. IASS-4 4” Midrange (Pair) 3. IASS-6 6” Midwoofer (Pair) II. SOUNDSTAGE CROSSOVER NETWORKS WITH VEHICLE-SPECIFIC TUNING & EQUALIZATION 4. MCSS630MW Mid-Woofer Network (Pair) 5. MCSS630T Tweeter Network (Pair) III. ARC AUDIO KS MINI AMPLIFIER (2CH W/SOUNDSTAGE, 4CH W/ SOUNDSTAGE + SUBWOOFER) IV. SIGNAL & SPEAKER WIRING HARNESSES 6. Signal Wiring Harness (MCWH-SIG-R) 7. Mid-Woofer Connection Harness (Pair) 8. Tweeter Pigtail (Pair) V. SOUNDSTAGE HARDWARE 9. Midrange Mounting Adapter

  • Integral Audio IASS-T, E. SUBWOOFER 19 64. REPEAT FOR THE RIGHT SIDE Repeat all of this section for the other side of the vehicle. Obvi- ously, you can omit the steps relating to the mirror switch! 65. SUBWOOFER INSTALLATION This entire section applies only to the subwoofer installation. If you are not installing the subwoofer system please proceed to Testing & Recommended Settings. 66. INSTALL NEUTRIK SPEAK-ON PLUG Split and strip the end of the Subwoofer Speaker wire. Slide the blue threaded bushing back. Thread the speaker wire through the bushing and the inner bushing. Loosen the clamping

  • Integral Audio IASS-T, E. SUBWOOFER 20 69. REMOVE ASPHALT PATCH On the driver’s side of the boot oor you will see an approximate- ly 2” x 2” asphalt patch. Use the stiff putty knife to remove it. It should remove easily, if not heating it with a heat gun (or hair dryer) will soften it. Cut a short strip of electrical tape and cover the hole - the enclosure side leg will sit over the hole. 70. MARK FOR BRACKET AND THREADED INSERT Temporarily replace the Wheel Arch Trim Panels, if previously removed. Place the enclosure in the boot, all the way forward and centered side-to-side in the carpet opening. Using a center punch (or marker), mark the c

  • D. SOUNDSTAGE 17 54. CROSSOVER CONNECTIONS Connect the stripped wires ends to the crossover board. The branch from the blue connector connects to the “IN”. The mid- range branch connects to “M”, and the woofer branch connects to “W”. Red is + and Black is - for all three. Place the Crossover in the armrest cavity. The armrest cover will hold it in place. IMPORTAN

  • Integral Audio IASS-T, D. SOUNDSTAGE 13 35. REMOVE LEFT WHEEL ARCH TRIM (PART 2) [HIFI/HK ONLY] Release expansion rivets (1) by prying out center pin. The trim panel (2) should open enough to access the amplier. *Left side is pictured, procedure for right side is the same. 36. ACCESS FACTORY AMP & WIRE LOOM [HIFI/HK ONLY] Remove screw (1) with a 10mm socket. Slide amp (2) towards the rear to release. Unplug amplier connector to access wire loom. Cut wrapping as needed to access wiring. Do not forget to recon- nect the factory amplier after making the speaker connections. 37. HIFI/HK SPEAKER WIRE CONNECTIONS [HIFI/HK ONLY] Re

  • Integral Audio IASS-T, A. PREP VEHICLE 6 1. REMOVE PASSENGER SEAT Slide the seat forward. Using a Torx T-40, remove the two screws holding the rear of the seat (1). Slide the seat backward and re- peat for the two front screws. 2. REMOVE PASSENGER SEAT (PART 2) Tilt the seat back. Disconnect the airbag wiring under the seat by pulling the black slide catch on the side of the yellow plug. Dis- connect the seat heater wiring if equipped. DO NOT put the key FOB in the ignition while this plug is disconnected. Remove the seat from the vehicle. 3. REMOVE PASSENGER SEAT (PART 3) If present, remove the plastic panel under the seat. 4. REMOVE DRIVER SEAT Re

  • Integral Audio IASS-T, C. SIGNAL WIRING 11 25. RUN SIGNAL WIRING TO AMP Beginning in the left (driver’s) side footwell, run the amplier end of the signal wiring bundle along the door sill, and under the carpet in the rear seat footwell area.power/ground wires. Be sure the wiring is clear of all pinch points, including the Seat Belt screw. AVOID PLACING SIGNAL WIRING DIRECTLY ADJACENT TO OR TOUCHING OTHER WIRING BUNDLES! 26. AMPLIFIER MOUNTING (OVERVIEW) The amplier mounts in the compartment under the passenger seat. If your vehicle does not have a compartment with cover un- der the seat, one has been included in your kit. You will cut the carpet, remove the foam block inside, and then mount

  • B. POWER & GROUND WIRING 8 11. REMOVE RIGHT COWL PANEL Open the Bonnet (aka the hood!). Remove the black plastic Cowl covering the battery by releasing nuts (2) and (3) with a 10mm socket. Loosen & remove cowl. NOTE: When replacing the cowl, be sure the seal (1) is seated properly and that the secondary tab of the cowl (4) is inserted into the plastic channe

  • Integral Audio IASS-T, F. SETTINGS 21 74. WIRING & NEUTRIK PLUG Connect the subwoofer internal wiring harness to the back of the Neutrik Speak-on connector (observing correct +/- polarity). Place the Speak-on gasket over the connector, thread the wire through the mounting hole, and mount the Speak-on connector using the (2) #4 x 1/2” screws. 75. MOUNT THE SPEAKER Mount the speaker with the #10 x 1” Black Pan Head Screws. Tighten the screws in a “star” pattern, go slowly and take care not to strip them. Make sure the speaker ange is

  • Integral Audio IASS-T, WHAT’S IN THE BOX 4 SUBWOOFER X. MC800S SUBWOOFER ENCLOSURE XI. INTEGRAL AUDIO ALCHEMY 10” SUBWOOFER XII. SPARE TIRE WELL COVER PANEL XIII. SUBWOOFER HARDWARE 21. Neutrik Speak-On Terminal & Gasket 22. ¼” x 1” Hex Head Bolt 23. #10 x 1” Black Pan Head Screw (8) 24. #10 x ¾” Pan Head Screw (8) 25. #4 x ½” Black Flathead Screw (2) 26. Threaded Insert (3) 27. Threaded Insert Installation Wrench 28. Subwoofer Mounting Bracket (2) 29. Rosette Thumbscrew (2) 30. Connection Harness (Sub to Neutrik) XIV. REMOTE LEVEL CONTROL 31. Integral Audio Remote Level Control 32. 3M VHB Double-Sided Mounting Tape (3in) SeSelect Hardware for Identification: 2

  • Integral Audio IASS-T, F. SETTINGS 25 92. ROCK. AND ROLL. That’s it! You should be ready to rock and roll. If you aren’t seriously impressed by the sound, something is wrong. Trust us on this. It should be clean, clear, and balanced. If it isn’t, revisit the steps above or reach out to us for support at 646-926-0011 or email us at [email protected]. 93. REPLACE ALL PANELS & TRIM All parts, panels, and trim install in the reverse order they were removed. 94. INTEGRAL AUDIO LOGO BADGES [All Vehicles EXCEPT 2010+ with HK] Remove the paper backing and afx

  • Integral Audio IASS-T, D. SOUNDSTAGAE 16 49. COVER CROSSOVERS WITH FOAM PADDING The crossovers get wrapped in foam padding, secured by zipties. The square pieces of foam are for the midrange/midwoofer cross- over, the narrow rectangular pieces are for the tweeter crossovers 50. COVER CROSSOVERS WITH FOAM PADDING Place each crossover component-side down. You want the seam of the foam to be on the smooth printed circuit board side of the crossover. Make sure the terminal connections for the wiring harness are on the open end. 51. COVER CROSSOVERS WITH FOAM PADDING Wrap the foam around e

  • Integral Audio IASS-T, E. SUBWOOFER 18 59. REMOVE/REPLACE TWEETER BADGES [2010+ HK ONLY] Remove the “Harmon/Kardon” tweeter badge by prying up gently with a at screwdriver. You need to insert the blade into the thin gap between the badge and the backing plate, not between the backing plate and the grill material. Replace with the adhesive Integral Audio badge by removing the backing and afxing in the recess in the tweeter grille. 60. INSTALL TWEETER Press the new tweeter squarely and rmly into the housing until it

  • Integral Audio IASS-T, F. SETTINGS 22 79. RECONNECT THE BATTERY & INSTALL FUSE Reconnect the Battery Negative Terminal and install the fuse in the fuse holder. 80. SETUP & TUNING YOU MUST DO EACH STEP EXACTLY AS DESCRIBED. IF POSSI- BLE, HAVE SOMEONE ELSE READ THE INSTRUCTIONS TO YOU WHILE YOU PERFORM THE STEPS. Do not reinstall any panels until you have conrmed that every- thing is operating properly. 81. REPLACE SEATS & RECONNECT AIRBAG WIRING If you removed them, replace the seats in vehicle and reconnect the yellow connector under the seat. You do not need to bolt the seat down yet. For under-seat amp installs, you can lean the seat back to gain ac

  • Integral Audio IASS-T, D. SOUNDSTAGE 14 39. HOW TO CHECK HIFI/HK PIN NUMBERS [HIFI/HK ONLY] Unplug the factory ampler connector by releasing the locking lever. Gently pry the black plastic housing out to release the locking tab. Slide the inner connectors out of the housing. You will see the pin numbers marked on the housing. Verify with the chart above 40. AMPLIFIER POWER & SIGNAL CONNECTIONS Connect the Power, Ground, and Remote Turn-on Lead wires to the amplier. Connect the RCA Interconnects. Set the INPUT selector on the amp to “RCA” (2ch amp) or “LOW” (4ch amp) Attach the amplier to the mounting plate using the #6 x 3/8” screws. [S

  • NOTES 26 NOTES • AMPLIFIER TURN-ON: You will notice that the amplier turns on before the head unit, and remains on after the head unit is off. This is normal. The sound output system needs to be energized to play your door chimes, parking distance control sounds, bluetooth, etc. The amp will turn on from the moment the doors are unlocked or opened, and remain

  • Integral Audio IASS-T, TOOLS YOU WILL NEED 5 IMAGES NOT TO SCALE I. PLASTIC PANEL REMOVAL TOOLS II. TORX BITS: 1. T25 2. T30 3. T40 4. T50 III. DRILL IV. DRILL BIT: 5. 7/16” [MUST be correct size!] V. WRENCHES OR SOCKETS: 6. 7/16” 7. 8mm 8. 10mm 9. 10mm Deep [optional} 10. 19mm VI. ELECTRICIAN’S WIRE FISH VII. SCISSORS VIII. UTILITY KNIFE IX. PLIERS X. DIGITAL MULTIMETER XI. TEST TONE CD (availble for download at www.integralaudio.com/other_files/test_cd/) XII. CENTER PUNCH [SUB ONLY] XIII. STIFF PUTTY KNIFE OR 5-IN-1 [SUB ONLY] XIV. WIRE STRIPPER [H

  • D. SOUNDSTAGE 15 44. REMOVE MIRROR CONTROL Carefully pry the Mirror Control (2) up at the bottom rear. Once it releases wiggle it up and out. Unplug connectors (1) and set aside. 45. MIDRANGE COVER Pull rmly up and in on the Midrange Cover (1) while pressing inward at the locations of the tabs (2). It is better to pull rmly than to try to pry at

  • Integral Audio IASS-T, B. POWER & GROUND WIRING 7 6. REMOVE LEFT DOOR SILL TRIM (PART 2) Remove metal seat belt bushing (1) if not removed in the previous step. Pull Rear Side Trim Panel (4) in, releasing clip (3) and freeing tab of Door Sill (2) located behind Side Panel (4). 7. REMOVE LEFT DOOR SILL TRIM (PART 3) [Seat shown removed for clarity] Remove the door seal over the entire length of the right door sill by lifting it up and off. Pull up/loosen the rubber door seal gas- ket along the length of the door. Pull Door Sill Pane

  • Integral Audio IASS-T, F. SETTINGS 24 88. CONFIRM SPEAKER CONNECTIONS & SETTINGS In the headunit, turn the Balance control to fade fully Left. Start at 20Hz on the test tone CD, play/skip through each higher fre- quency to 4kHz. You should hear the subwoofer rst, then at ~60Hz you’ll transition to the door mid-woofer, then at ~150Hz you’ll transition to the midrange, and then the tweeter beginning at ~2.5kHz. You should hear each speaker on the left, in the cor- rect order. You may get some sound from the right, but it should be low level. Then fade the Balance all the way to the Right and repeat the process for the right side. 89. AMPLIF

Related Products and Documents (Car Stereo System):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 LG HDR-798 Owner's manual lg/hdr-798-42P.pdf 05 Nov 2023 59
2 Cisco SD2008T-NA Configuration manual cisco/sd2008t-na-K5R.pdf 11 May 2023 46 1.08 Mb
3 TRENDnet TFC-110S40D3 Specifications trendnet/tfc-110s40d3-GI4.pdf 01 Nov 2023 2 0.31 Mb
4 Allied Telesis Converteon AT-CV5000 Installation manual allied-telesis/converteon-at-cv5000-BMG.pdf 20 Jun 2023 114 5.66 Mb
5 Alliance Laundry Systems Topload Washer Installation instructions manual alliance-laundry-systems/topload-washer-897.pdf 25 Sep 2023 12 0.69 Mb
6 Samsung CE107B-B Owner's instructions and cooking manual samsung/ce107b-b-YJQ.pdf 15 Dec 2023 32 2.5 Mb

Similar Resources:

  • Pioneer

    DEH-P3800MP - Radio / CD

    (59 pages)
    Operation ManualMode demploiMulti-CD control High power CD/MP3/WMA playerwith FM/AM tunerSyntoniseur FM/AM et lecteur de CD/MP3/WMA,Puissance élevée, avec contrôleur pour lecteur deCD à chargeurDEH-P3800MPEnglish EspañolFrançais …
  • Discount Car Stereo

    A2D-KNW

    (4 pages)
    Courtesy of: DiscountCarStereo.com Serving the internet community since 1995 A2D-KNW BLUETOOTH MUSIC STREAMING INSTALLATION GUIDE FOR SELECT KENWOOD AUX READY RADIOS …
  • Sony

    CDX-GT700HD - Fd 8g Usb 1wire

    (2 pages)
    CDX-GT700HDCDX-GT700HD CD Rece iver Multi-format playback lets you play CDs, CD-Rs, or CD-RWs loaded with hundreds of MP3 or WMA songs .1 The 2-line LCD makes it easy to read song information and the front auxiliary input lets you connect almost any portable audio device to your car's sound system.USB1-Wire for iPod®products, iPhone®, and other …
  • Blaupunkt

    CD 2001

    (10 pages)
    288F0050CD 2001High-Power FM/AM/CD Receiver with Detachable FaceAutoradio AM/FM à Lecteur CD de Forte Puissance et à Face AmovibleReceptor FM/AM/Reproductor de CD de Alta Potencia y con Panel ExtraíbleRádio FM/AM/CD de Alta Potênciacom Face RemovívelRobert Bosch CorporationSales Group —Blaupunkt Division2800 South 25th Avenue,Broadview, Illinois 6015 …
  • JVC

    KD-DV9406

    (68 pages)
    For canceling the display demonstration, see page 7.For installation and connections, refer to the separate manual.INSTRUCTIONSGET0541-005A[A]KD-DV9406/KD-DV9405DVD/CD RECEIVERCover_KD-DV9406_005A_1.indd 1Cover_KD-DV9406_005A_1.indd 1 22/4/08 4:12:39 PM22/4/08 4:12:39 PM …
  • Sony

    XM-1502SX - Stereo Power Amplifier

    (62 pages)
    Training ManualCourse: A-125Car Amp & Video,& Music Storage UnitsModels: XM-1502SX XM-475GSXXM-2150GSX XM-1902SXDRN-XM01 XM-5150GSXXT-XM1XAV-7WXVM-R75MEX-5DiMEX-1HDCircuit Descriptions & TroubleshootingXM-2150GSXXVM-R75MEX-5Di …

Comments, Questions and Opinions: