CTC Union DIYFDM 1 Installation And Use Manual
|
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 11 the EXP2 port of LED motherboard. Figure 20 LED Position 7. Installation of Q Assembly Notes: Because each size of assembly may bear some deviation caused by production, in order to obtain the good installation and functions, it is advisable for you to pay attention to the installation of Q assembly. If necessary, please adjust the right side of Q assembly to left or right for ensuring the normal functions, and adjust the length of belt according to actual gap. Before assembly, the first Z-axis screw M5 ends conn
Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 4 Figure 5 Left View of Main Framework Figure 6 Connection of Boards and Assemblies Installation of Motherboard 1. A1 Assembly Accessories: ○ 20 , ○ 7 ×4, ○ 8 ×4, ○ 3 ×4, ○ 4 ×4. Install cooling fan to the back of left cooling outlet of A1 board of main framework with accessories ○ 7 , ○ 3 and ○ 4 . The
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 27 Open the power source motherboard (in the following picture) and press function key to enter parameter setting center and to set the nozzle temperature, bed temperature (nozzle is 210 ℃ and bed is 60 ℃ generally). Then return the main menu and choose Print form SD to select the to-be-printed model. Then “Heating…”is displayed until the set temperature. The printing is started. The to be Cura 14.07 document must be in STL format, to-be-printed document must be in GCODE format. Double-click the icon to ope
Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 3 5 P Assembly 1 Figure 16 3. Notes Before installation, find A1 board, A2 board and A3 board, then align the holes of each board. Use ○ 3 , ○ 4 and ○ 6 to install each board for assembling a main framework. The installation direction must comply with the following figures (Figure 1 to Figure 5). The connection of
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 34 1、Print form SD (choose model to print from SD card) 4.1 main (return to superior layer) 4.2------- ) (SD card, printing model name) During printing, click function key to enter the following interface and adjust relevant parameters.: 1、Info Screen (return to main screen) 2、Tune (fine-tuning) 2.1main (return to superior layer) 2.2speed (printing speed) 2.3Nozzle (nozzle temperature) 2.4Bed (bed temperature) 2.5Fan speed (fan speed) 2.6 Flow (material flow) 2.7 Flow (material flow) 2.8 Change filament( (change printing filament) 3、Control (
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 10 Connect the bottom heating cable to the port 2 of motherboard. Connect the temperature sensor cable of bed to the port 22 of motherboard. Connect the stopper(blue)cable port to the port 17 of motherboard. Figure 18 Figure 19 4. Installation of A4 Assembly Accessories: ○ 6 ×3, ○ 4 ×3, ○ 3 ×3. Align the holes of A4 assembly to the A1 board of front side of main structure, and connect the A4 assembly to the bottom end of left side of A1 assembly. Then connect the motor to port 15 of motherboard with short cable ○ 19 and stopper (black) cable to the port 16 of motherboard. 5. Installation of
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 1 Introduction Because the voltage under which this printer is used varies from one region to another, please first confirm the voltage of your region before using this printer (110V or 220V). Printer maintenance conducted by customer is required after this printer is used for sometime. Frequent and correct maintenance can extend the using lifetime of printer. 1. Safety Issues In order to obtain the best 3D printing effect, we do not recommend you to use the consumables of other brand other than the exclusive consumables provided by us. The maintenance and repairs caused by
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 47 Maintenance 1. Cleaning Nozzle You need to clean the nozzle after printer is used for some time. Dismantle nozzle, remove fan, motor and the black square at the material inlet of motor, on which is the rubber extruding gear of nozzle. Open this square and clean the plastic rubber in the gear. Then install these parts back to printer. 2. Tightening Belt Notes: 1.Belt should be seamlessly contacted with belt wheel. 2. Forces of the two side of Y sha
Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual I Contents Introduction ....................................................................................... 1 1. Safety Issues ............................................................................. 1 2. Materials and Parts ................................................................... 1 3. Notes .
Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 46 6.5 Then online-printing window is popped out. When the “print” turns black, it means the printer has been successfully on-line. Then click “Print” to heat nozzle and bed until the temperature reaches pre-set value. Then printer will return to starting position and began to print on
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 32 2.3 Auto home (initial printing point) 2.4 Preheat PLA (Preheat PLA) 2.5 Preheat ABS (Preheat ABS) 2.6 Cool down (cool down) 2.7 Switch power on/off 2.8 Move shaft (move each shaft) 2.8.1Prepare (return to the superior layer) 2.8.2move 10mm (move in the unit of 10mm) 2.8.2.1move shaft (return to the superior layer) 2.8.2.2move x (move X shaft) 2.8.2.3move y (move Y shaft) 2.8.3move 1mm (move in the unit of 1mm) 2.8.3.1move shaft ( return to superior layer ) 2.8.3.2move x (move X shaft) 2.8.3.3mov
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 29 Automatic Slicing After slicing, the icon will be shown and choose the middle online –printing icon. If the middle icon is storage after slicing, then you have to choose“Save”.
CTC Union DIYFDM 1, ZHUHAI CTC ELECTRONIC CO., LTD CTC DIY Printer Installation and Use Manual A mature brand that has been tested by 10-years’ time focus on high-end science and technology, focus on 3D printing Thank you for purchasing the DIY 3D printer manufactured by Zhuhai CTC Electronic Co., Ltd. Please carefully read this installation and use manual before installation and use. Website: www.ctcprint.com
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 8 fan; 17. Z shaft stopper; 18. Y shaft stopper; 19. X shaft stopper; 20. LED. 21 bar cable ports of.SD card display; 22.temperature sensor socket of R nozzle; 23.temperature sensor socket of L nozzle 24.temperature sensor of heating bed(spare); 25.function reset key of motherboard. 1. collect all the assemblies before installation: A4, A5, LED, P,Q(different colors) as shown in the following figures. Figure 12 A4 Assembly Figure 13 A5 Assembly Figure 14. LED (front side on the left and back side on the right)
CTC Union DIYFDM 1, Zhuhai CTC Electronic Co., Ltd DIY Printer Installation and Use Manual 44 6.2 Set the filament diameter as 1.75mm and nozzle diameter is 0.4mm. 6.3 Click the first icon to pen file folder . Then choose the to-be-printed STL file.
TRAK 3ntr Series 3D Printers Quick start manual
3ntr Series |
Carbide3D BitSetter 3D Printers Installation and setup manual
BitSetter |
weistek IdeaWerk 3D Printers Product user manual
IdeaWerk |
3DCPI 3DCPI-03 3D Printers Startup manual
3DCPI-03 |
3DISON H700 3D Printers Operation & user’s manual
H700 |
Flashforge Finder 3D Printers Start up and instruction manual
Finder |
CTC Union DIY 3D 3D Printers Installation instruction
DIY 3D |
BCN3D Sigma 3D Printers Operation & user’s manual
Sigma |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Electrolux | TF1107 | Instructions for installation and use manual | electrolux/tf1107-548.pdf | 23 May 2023 | 12 | 1.25 Mb |
2 | ACS | ACR1281U-C2 | Reference manual | acs/acr1281u-c2-J21.pdf | 05 Mar 2023 | 15 | |
3 | Coherent | wavemaster | Operation & user’s manual | coherent/wavemaster-A27.pdf | 19 Jan 2024 | 44 | |
4 | Radio Shack | FRS-101 | Owner's manual | radio-shack/frs-101-ND2.pdf | 02 Jan 2024 | 4 | 0.05 Mb |
5 | EV LIGHT | EV S155 | Operation & user’s manual | ev-light/ev-s155-G65.pdf | 07 Jul 2023 | 6 | |
6 | Canon | 8580A001 | Specification | canon/8580a001-O19.pdf | 29 Nov 2022 | 2 | 0.44 Mb |
MUTOH
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Connecting Power and Network . . . . . . . . . . . . . . . 13Printer Initial Setup . . . . . . . . . . . . . . . …
XpertJet XPJ-1641SR(48 pages) |
Flashforge
This guide is only applicable to FLASHFORGE Hunter 3D printerThe User Guide is in the USB stick.WARNINGUSERGUIDE2. To ensure the printing quality, please don't open the light shield unless it's necessary.3. Unused photopolymer resin needs to be stored in a dark, dry, and cool place.4. Please clean the finished model with isopropyl alcoh …
Hunter(19 pages) |
Z Corporation
Z402C System User Manual November 2001 ZTM402C 3D Color Printer User Manual Z Corporation Software Version 5.1.40 Copyright©2001 Z Corporation Part Number 09501
…
Z402C(57 pages) |
SainSmart
[email protected] of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.SainSmart Coreception 3D Printer Trouble Shooting1. Cura settings (specifically print head size settings and why they are)There is a known bug for the x-min and the y-min. These settings are used to set the hotend s …
Coreception(11 pages) |
BCN3D
Install printing surfaceWatch our video to see how to correctly position the build plate.Set up videoWe would like to thank all users for trusting BCN3D, for helping us to reach our dreams and to create a better product every day.1. Unboxing1. Remove the components from the foam and place them on a table. Then remove the foam and the cardboard. 2. Rem …
Sigma Series(2 pages) |
Kohon
KH-01 Series 3D PrinterM a n u a lM a n u a lM a n u a lI n s t r u c t i o nI n s t r u c t i o nI n s t r u c t i o n The manual is made according to KH-01 standard specification,and also applicable to all KH-01/KH-02/KH-03/KH-04/KH-05 Series. Take practicality as standard of appearances and interfacesbecause of software & hardware upgrades. D …
KH-01 Series(16 pages) |
K-Star Ventilation Hood K1032Operating instructions manual for K-Star K1032 Ventilation Hood K1032, 16 |
LENCO Welding System L-6000Specification sheet for LENCO L-6000 Welding System L-6000, 1 |
Rotel Amplifier HIFI RB951Amplifier PDF Owner's manual HIFI RB951, 7 |
Dukane Projector ImagePro 7250#72RS26: ImagePro 7250 Projector Specification ImagePro 7250, 2 |
Craftsman Lawn and Garden Equipment 917.28732917.28732 Operator's manual - 751CM8 917.28732, 68 |
Polar Electro Heart Rate Monitor 19627425.00Polar Electro 19627425.00 Heart Rate Monitor Easy manual 19627425.00, 6 |
Loctite Amplifier 97211Loctite 97211 Amplifier Operating manual 97211, 56 |
Shark Engine SSG-503027E, SSG-503027G, SSG-Guide: Shark SSG-503027E, SSG-503027G, SSG- (BBL1L6, Upd.28.08.2023) SSG-503027E, SSG-503027G, SSG-, 34 |
Troy-Bilt Trimmer TB20DCManual: Troy-Bilt TB20DC (SP4UJ3, Upd.01st Nov 2023) TB20DC, 64 |
Yamaha DVD Player DVD-S1200Yamaha DVD-S1200 DVD Player Service manual DVD-S1200, 84 |
Philips Monitor 220SW9FB/27#DITC9D 220SW9FB/27: Philips Monitor Owner Documentation 220SW9FB/27, 119 |
Spin Master Toy Paint Sensation#RM4YBP Paint Sensation: Spin Master Toy Owner Documentation Paint Sensation, 6 |