Panasonic MX-GX1561 Operating Instructions Manual
|
Operating Instructions Blender (household use) Table of Contents Safety Precautions ••••••••••••••••••••••••••••••••••••••2 Parts ••••••••••••••••••••••••••••••••••••••6 How to Use Blender ••••••••••••
Panasonic MX-GX1561, 2 ﺭﺍﺩﺷﻫ ﻪﻳﺑﻧﺗ ﺭﺍﺩﺷﻫ ■ ■ ■ ■ ■ ■ Safety Precautions Always follow these precautions In order to prevent the risk of danger to the users of this product or those nearby, and damaging property, be sure to follow the safety precautions outlined below. ■ The following signs are used for precautions. They are separated depending on the degree of the danger or damage that may occur if their contents are ignored while using this unit. ■ The following signs are used to explain operations that you are requested to follow. They are separated as shown below. WARNING CAUTION This sign warns you that death o
Panasonic MX-GX1561, 3 ﺭﺍﺩﺷﻫ WARNING This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible their safety. Children should be supervised to ensure that they do not play with the product. Do not immerse the motor housing into the water. Do not try to put on or remove the container when the motor is still rotating. Never put spoon, fork or spatula into the container while operating the
Panasonic MX-GX1561, 4 ﺭﺍﺩﺷﻫ ﻪﻳﺑﻧﺗ WARNING CAUTION Please make sure that voltage used for this product is suitable to the local area voltage. Never use hot water (over 60 °C) for cleaning purpose or for drying it. Care shall be taken when handling the sharp cutting blades, emptying the container and during cleaning. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly persons in order to avoid a hazard. Remove dusts or dirts at plug regularly. Do not place the hot ingredients (over 60 °C) into the container. Do not operate without the container and cover in place correctly. Never wash the mot
Panasonic MX-GX1561, 5 ﻪﻳﺑﻧﺗ Remove packing materials, such as plastic bags or plug cap etc from the appliance. Discard them or keep them away from babies and children. (Otherwise it may cause suffocation.) ﺵﻮﭘﺭﺩ ﺎﻳ ﯽﮑﻴﺘﺳﻼﭘ یﺎﻫ ﻪﺴﻴﮐ ﻞﻴﺒﻗ ﺯﺍ یﺪﻨﺑ ﻪﺘﺴﺑ ﺩﺍﻮﻣ .ﺪﻳﺭﺍﺩﺮﺑ ﻩﺎﮕﺘﺳﺩ ﺯﺍ ﺍﺭ ﻩﺮﻴﻏ ﻭ ﺮﻴﮕﺧﺍﺭﻮﺳ .ﺪﻳﺭﺍﺩ ﻪﮕﻧ ﻥﺎﮐﺩﻮﮐ ﺱﺮﺘﺳﺩ ﺯﺍ ﺭﻭﺩ ﺎﻳ ﺪﻳﺰﻳﺮﺑ ﺭﻭﺩ ﺍﺭ ﺎﻬﻧﺁ (.ﺪﻧﺩﺮﮔ
7 • • • To disassemble Blender To disassemble Mill To assemble Blender To assemble Mill mill container base mill gasket Turn blender container base counterclockwise to disassemble. Twist the mill container base counterclockwise. Turn blender container clockwise to assemble. • Make sure that gasket is set properly and container is tightened properly to prevent leak
Panasonic MX-GX1561, 8 • • • • • • • How to Use Blender CAUTIONS: • First, dice the ingredients (cut them into cubes measuring 1 to 2 cm), and put them in water. • Put the ingredients in the container starting with the softer ones • Do not place ingredients with a maximum total volume mL • Do not put the following kinds of ingredients in the container: Meat, hard foods (such as dried soybeans, turmeric or frozen food items), very sticky foods (such as peanut butter), foods with a low
9 1 2 Place the ingredients in the blender container. Check that the cover is in place to prevent the ingredients from out. Mount the blender container on the motor housing. Twist the container clockwise until it locks into place. When adding ingredients or seasonings, remove/attach inner cap whilst holding the container. Add ingredients as shown left. ﻮﻫ
10 3 blended, power outlet. Twist When disconnecting the power plug, be absolutely sure to take hold of the molded plug. Never pull on the cord. After the ingredients have been Disconnect the power plug from the the blender container counterclockwise to remove it from the motor housing, and take out the processed ingredients. 馬達罩 ﻒﻟﺎﺘﻟﺍ
Panasonic MX-GX1561, 12 1 2 outlet. Turn the mill container upside down, and place the ingredients in it. Twist the mill container base clockwise until it locks into place, and mount it onto the mill container. Place the mill container and mill container base on the motor housing. Twist the container and base clockwise until they lock into place. Connect the power plug to the power 乾磨器 乾磨器 ,將其鎖定。 馬達罩 乾磨器 乾
Panasonic MX-GX1561, 13 3 mixed the power outlet. Remove Wait for the mill to stop rotating before removing your hand. When disconnecting the power plug, be absolutely sure to take hold of the molded plug. Never pull on the cord. After the ingredients have been Disconnect the power plug from the mill container base from the motor housing, turn it upside down, and tap the container gently with your hand to dislodge the ingredients from the cutter. Remove the mill container base by twisting counterclockwise and take out the processed ingredients. ﻮﻫ 中斷
Panasonic MX-GX1561, 14 Safety Lock The safety lock has been designed to prevent the blender from switching on when container is not properly in place. Do not push the safety lock pin with any implement, stick etc. gnirud dehsup si esab reniatnoc eht fo kcab eht no nip ytefas eht nehW assembling, motor does not operate. Safety lock pin Safety pin 刀座
Panasonic MX-GX1561, 15 1 2 3 one-at-a-time in order: > 切削刀 > . and then press the following buttons Reduce the amount of the ingredients inside the container by half. Circuit Breaker Protection If the motor is subjected to an excessive load, its protection device is tripped, shutting down the motor automatically. It is reset by taking the steps described below. 截
Panasonic MX-GX1561, 16 • • • • • • • How to Clean NOTES: • Before cleaning the blender, disconnect the power plug from the power outlet. • Handle the cutter carefully. • To clean the parts, use cold or lukewarm water and a soft sponge. • Do not use steel brushes or other abrasive cleaning materials or utensils. • Do not use benzene, paint thinners, alcohol or other solvents. • Do not use a dish washer/drier or a dishwasher. • The cover and insides of the containers may become slightly discolored through use.
Panasonic MX-GX1561, 17 Wash the parts using a soft sponge soaked in diluted kitchen detergent (neutral). To remove ingredients stuck in the cutter, carefully clean it with a brush. Then rinse thoroughly with water, and allow the parts to dry out. Carefully clean mill cutter with a brush. Do not use water. Wipe with a well wrung-out cloth. Mill cutterContainers and plastic parts Motor housing 乾 乾
Panasonic MX-GX1561, 18 Problems Possible cause Page The blender does not operate • • • • • • • Troubleshooting See P.9 & P.12 The blender stops operating midway through operation. • The Circuit Breaker Protection of the motor has been tripped. Check whether prohibited, hard or too many ingredients have been placed in the container. • The Circuit Breaker Protection will also be tripped when abnormal sounds are heard or high levels of vibration are generated. See P.15 The ingredients being processed are leaking out. • The blender
Panasonic MX-GX1561, Note In case of failure or damage You can identify the date of manufacturing by number which is marked on bottom side of the unit. Number marked on bottom side of the unit: X X X X X X Fifth and sixth digits: day (in number) 01, 02, 03...31 Third and fourth digits: month (in number) 01--January, 02--February, ...12--December First and second digits: year (last two digits of the year in number) 10--2010, 11--2011, 12--2012 This operating instructions shall be kept as they contain important information. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest authorized s
Panasonic MX-GX1561, MX-GX1561: 220 W / MX-GX1511: 230 W 厘米 厘米 厘米 / 220 V 50 Hz Web Site: http://www.panasonic.com X0921-351 Approx. 1.8 kg MX-GX1561: approx. 3.4 kg MX-GX1511: approx. 2.2 kg :MX-GX1561:MX-GX1511 / :MX-GX1561:MX-GX1511 / 乾磨器 千克 千克 千克
Panasonic MX-151SG2 Blender Operating instructions manual
MX-151SG2 |
Panasonic MX-SM1031 Blender Operating instructions manual
MX-SM1031 |
Panasonic MX-AC400 Blender Operating instructions manual
MX-AC400 |
Panasonic MX-ZX1800 Blender Operating instructions manual
MX-ZX1800 |
Panasonic MX-AC300 Blender Operating instructions manual
MX-AC300 |
Panasonic MX-SS1 Blender Operating instructions manual
MX-SS1 |
Panasonic MX-ZX1800 Blender Operating instructions manual
MX-ZX1800 |
Panasonic MX-KM5060 Blender Operating instructions manual
MX-KM5060 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Panasonic | KX-TG1062 | Operating instructions manual | panasonic/kx-tg1062-531.pdf | 03 Mar 2024 | 60 | 3.06 Mb |
2 | Hanns.G | JC199 | Operation & user’s manual | hanns-g/jc199-L75.pdf | 29 Dec 2023 | 20 | 1.29 Mb |
3 | Slick | MP82 | Owner's manual | slick/mp82-G3B.pdf | 23 Nov 2023 | 1 | 2.34 Mb |
4 | Asus | E45M1-I DELUXE | Operation & user’s manual | asus/e45m1-i-deluxe-TF6.pdf | 01 Nov 2023 | 56 | 1.46 Mb |
5 | Intermatic | LT401 | Instructions | intermatic/lt401-7YB.pdf | 30 Aug 2022 | 2 | |
6 | Silvercrest | MTS2219-SLN | User manual and service information | silvercrest/mts2219-sln-KZ2.pdf | 21 Mar 2024 | 44 | 2.54 Mb |
Bosch
Register your new device on MyBosch now and get free benefits:bosch-home.com/ welcomeMSM6...INErgoMixxAccessories (Hand blender)[en] Instruction manual Accessories (Hand blender) 7
…
ErgoMixx MSM6 IN Series(12 pages) |
Heinner
STAND BLENDER Model: HBL-1000BRW www.heinner.com Stand blender Max power: 1000W Color: black with stainless steel base
…
HBL-1000BRW(29 pages) |
Hotpoint Ariston
IT Istruzioni per l’usoEN Operating instructionsFR Mode d’emploiRU ИнструкциипоэксплуатацииTR KullanmatalimatlarıPT Instruções de UtilizaçãoUA ІнструкціїзексплуатаціїKZ ПайдаланунұсқаулығыBG Инструкциизаупотре� …
TB 060C AX0(84 pages) |
Breville
www.breville.com.auBreville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928. Copyright Breville Pty. Ltd. 2011. Due to continued product improvement, the products illustrated/photographed in this brochure may vary slightly from the actual product.BBL420 Issue - C11Australian CustomersMail: PO Box 22 Botany NSW 2019 AUSTRALIA Phone …
Kinetix Aero BBL420(32 pages) |
Brabantia
TECHNICAL DATARated voltage: 220-240V ~ 50/60HzPower: 1000WTECHNISCHE GEGEVENSNominale spanning: 220-240V~ 50/60HZVoeding: 1000WSPECIFICATIONVoltage : 220-240V~ 50/60HzPuissance : 1000WESPECIFICACIONESVoltage: 220-240V~ 50/60HzPotencia: 1000WSPECIFICHEVoltaggio: 220-240V~ 50/60HzPotenza: 1000WTECHNISCHE DATENBetriebsspannung: 220-240V~ 50/60HzSpannung: 1000W …
BBEK1052MB(13 pages) |
Silvercrest
5IAN 75748 IAN 75748KOMPERNASS GMBHBurgstraße 21D-44867 Bochumwww.kompernass.comEstado de las informaciones · Versione delle informazioniLast Information Update · Stand der Informationen: 06 /2012 · Ident.-No.: EDS-SSM600B2042012-2BATIDORA DE BRAZO FRULLATORE AD IMMERSIONE EDS-SSM 600 B2BATIDORA DE BRAZOInstrucciones de uso HAND BLENDEROperating instruct …
EDS-SSM 600 B2(58 pages) |
Electro-Voice Speakers SX300PI#AT369I SX300PI: Electro-Voice Speakers Owner Documentation SX300PI, 4 |
Blaupunkt GPS TravelPilot DX-V#LKMV56 TravelPilot DX-V: Blaupunkt GPS Owner Documentation TravelPilot DX-V, 78 |
NETGEAR Switch SMART SWITCH GS700TS#ALS39A SMART SWITCH GS700TS: NETGEAR Switch Owner Documentation SMART SWITCH GS700TS, 4 |
Whirlpool Dishwasher ADP 7955 TOUCHDishwasher Quick reference manual (Whirlpool ADP 7955 TOUCH) ADP 7955 TOUCH, 12 |
Totevision TV LCD-4200VTTotevision TV LCD-4200VT Operation & user’s manual LCD-4200VT, 16 |
Barazza Oven 1FLBMP9#YL4PTV 1FLBMP9: Barazza Oven Owner Documentation 1FLBMP9, 32 |
Garudan Sewing Machine GP-514-446#375AV1: GP-514-446 Sewing Machine User manual and spare parts list GP-514-446, 68 |
Microtek Scanner ScanMaker 3700#62BWGX: ScanMaker 3700 Scanner Supplementary manual ScanMaker 3700, 84 |
Carrier Furnace 58SE-05058SE-050 Installation, start-up and service instructions manual - 8A2ZK2 58SE-050, 17 |
Timex GPS Run Trainer 2.0 GPSGPS PDF Operation & user’s manual Run Trainer 2.0 GPS, 188 |
Cisco Switch Catalyst Express 500Cisco Catalyst Express 500 Switch Getting started manual Catalyst Express 500, 24 |