Jasco EasyCam Pro Operation & User’s Manual

Text of Jasco EasyCam Pro User Guide:

• Jasco EasyCam Pro, 1 EasyCam Pro User’s Manual Table of Contents 1. Getting Started............................................................................. 02 a. Package Contents....................................................................................... 02 b. System Requirements.................................................................................. 02 c. EasyCam Pro Camera View Nomenclature ............................................... 02 d. Verifying USB Presence.................................

• Jasco EasyCam Pro, 2 ● EasyCam Pro Camera ● USB connector cable ● Quick Start Guide ● Installation CD-ROM ○ Camera Driver ○ Application Software ● ArcSoft VideoImpression 1.6 ● ArcSoft PhotoImpression 3.0 ○ User’s Manual ● Intel Pentium II 350MHz Processor or equivalent ● 64MB System RAM ● Windows 98SE/Me/2000/XP ● CD-ROM drive ● 16-bit true color display or higher Optional for VideoConference ● Full- or half- duplex sound card ● Modem for dial-up connection (or corporate internet) ● An authorized Internet account (user ID or IP address). 1. Unpacking the EasyCam Pro package and checking components O

• Jasco EasyCam Pro, 3 Power up your computer and check to see if USB is implemented. Visually inspect the USB ports of your computer. If you cannot find the USB ports at the back of your computer (See Figure 1), read the documentation that came with your computer main board. For computer main board with USB supported: Enter BIOS settings and enable USB, see the documentation that came with your computer. Normally, when the computer power is turned on, before starting windows, the computer will hint you to press some keys for displa

• Jasco EasyCam Pro, 4 1. Installing the camera and driver Before installing Camera to your computer, make sure Windows starts up. Then follow the steps below: 1. Plug the camera's connector to the USB port on your computer. (See Figure 2) 2. Check to make sure you have the correct orientation while plugging the USB connector into the USB port of your computer. 3. Once Windows has detected new hardware added to the system, an USB Device message appears on the screen, asking you to search a new device. 4. Click “ Next ” to continue. 5. In this dialog box, you will be a

• 5 9. When you have finished the location selection, click “Next” to continue. 10. Windows will search for the EasyCam Pro device and driver location. Note: The driver file should read: d:\driver\twnkcam.inf 11. Click “Next” from the above screen, Windows will copy Driver files into your system. 12. Click “Finish” to complete the EasyCam Pro driver installation.

• 6 1. Insert Installation CD into your CD-ROM drive. 2. An Introduction screen will appear with a menu or CD contents. Note: If the installer screen does not come up automatically, click “Start”, “Run”, and execute the file “cdsetup.exe” on the CD to start the installer program. 3. Click “VideoImpress 1.6”. 4. Follow on screen waited instru

• Jasco EasyCam Pro, 7 1. Click Start> Programs> ArcSoft VideoImpression 1.6> ArcSoft VideoImpression 1.6. 2. The introduction screen will appear with a menu of software contents. 3. Click “ New. ” 4. Select “Capture” . The window shows a Live preview as seen from the EasyCam Pro. 5. To focus the picture, turn the focus ring (the grooved plastic ring around the lens of the camera) until the image becomes sharp. 1. Click Start> Programs> ArcSoft VideoImpression 1.6> ArcSoft VideoImpr

• Jasco EasyCam Pro, 8 1. Follow steps 1~3 in “Set the Focus” to enable live preview. 2. To stop preview, click on “Stop” ( ). 3. To resume preview, click on "Preview" ( ). 1. Follow steps 1~3 in “Setting the Focus” to enable live preview. 2. To start video recording, click on “Record” ( ). 3. To stop video recording, click on “Stop” ( ) or ESC. 4. To save captured video, click on “Save” ( ). 1. In VideoImpression Main Screen, select “New.” 2. Select source for replay by clic

• Jasco EasyCam Pro, 9 You can create movies by placing image and movie files onto the Storyboard from various Albums. To create a movie, do the following: 1. Click on the New icon from the Main Screen. This will take you to the Album Screen. 2. Use the options on the Album Screen to construct your movie. Select Album - (Located immediately to the right of the album name) Lets you choose the album you wish to view or work from. Selecting “New” will bring up a new, empty album. You can name/rename an album by clicking in the box with the album name and typing over the existing text. Get - Opens a window that allow

• 10 Note: The Storyboard shows you each step or part of the movie that you are creating. You can add a thumbnail to your Storyboard by drag-n-drop, or by highlighting a thumbnail and clicking on the Add To Storyboard icon. Text - Is highlighted if there is text added to the respective thumbnail. You can add text by clicking on the thumbnail and then

• Jasco EasyCam Pro, 11 To edit still images, double click on the review window in “Still Image Template” Play Movie - Takes you back to the View Screen where you can play, save, and email your movie. Transitions - Takes you to the Transitions Screen (See “ Options on the Storyboard ” ). Album - Takes you to the Album Screen (See “Working with Albums” ) Text - Allows you to add text to images. You can select the font type, style and size. You can also apply effects to the text, and adjust their duration. Brightness Slider - Allows you to change the brightness of an image. This is the top slider below the preview window. Contrast Slider -

• Jasco EasyCam Pro, 12 1. From the Edit Screen, select the video frame you want to print. 2. Right-click the video and select “Print.” 1. Click on Save on the Main Screen. 2. In the Save As window, select the drive and folder that you want to save the movie to. 3. Give the file a name, and select what type of movie you want to save it as. 4. Click Okay to save, or Cancel to abort Saving a Movie Printing a Snapshot Image or a Still Image from a Video

• Jasco EasyCam Pro, 13 1. Click Start. 2. Select Programs>ArcSoft PhotoImpression>PhotoImpression 3.0. The PhotoImpression Main Screen will appear on your desktop. Options on the Main Screen: - Opens images from an album (Album), a disk drive (From Folder), or from photo-sharing website (Online Service). You can also acquire images from TWAIN devices (Camera/Scanner), get screenshots (Screen Capture), and create new images from scratch (Create New). - Brings up editing tools for manipulating images. Options include Crop/Resize Retouch, Text, Enhance, Effects, and Layers. - Brings up creative options, includ

• Jasco EasyCam Pro, 14 Toolbar: - Resizes the image when the corner handles are dragged. You can also reposition the image by dragging it. - Rotates the image at the user’s discretion. - Applies a mirror effect to your image by flipping it. - Rotates the image in 90-degree increments. - Cancels the last unsaved change you’ve made. - Reverses the last action you’ve undone. - Copies the selected area, layer, or image onto the Clipboard. - Pastes what’s on the Clipboard onto the selected image as a new layer. - Deletes the currentl

• Jasco EasyCam Pro, 15 You can open an image that is stored on your hard drive, floppy disk, CD-ROM, etc. 1. Click the Get Photo button on the Main Screen, and select From Folder. 2. Click Browse. A Browse for Folder dialog will appear. 3. Navigate to the folder that you wish to view. Highlight the folder and click OK. 4. Thumbnails of the images within the selected folder will appear. Highlight the desired thumbnail, and click OK (or double-click it). 1. Click the Get Photo button on the Main Screen, and select . 2. From the pull-down, select the desired device. 3. From the pull-down, select the desired album to which the acquired file will be added. 4. Click the Acq

• Jasco EasyCam Pro, 16 Photo albums allow easy identification and access to images for viewing, editing, printing, etc. Simply click on the Get Photo button on the Main Screen, and select Album to view the album options. It is important to remember that albums do not store images. When an album is created, thumbnails are generated and a reference to where the files are located is recorded in the album file. For example, if a thumbnail is added into an album from a floppy disk, that floppy disk must be in the floppy drive in order to view the file. Album Tools: Album Selector - Allows y

• 17 Click the Edit button on the Main Screen to display the various editing options. Crop/Resize: - Allows you to select a rectangular area on an image. - Works the same as the Rectangle tool except a circle is drawn instead of a rectangle. - Allows you to make a "freehand" selection by clicking and dragging over the image in a desired path or shape. You can se

• Jasco EasyCam Pro, 18 - Reduces the red-eye effect common in flash photography. - Smoothes rough edges. - Sharpens fuzzy areas. - Lowers brightness. - Raises brightness. - Lets you set a color on your image as the active color. - Covers the area you click on (based on color similarity) with the active color. - Fills a layer or image with a selected pattern. - Fills the current image or layer with a gradient from the alternative color to the active color. Select the desired colors in the Color Palette, click at the point where you want the gradient to start, and drag to designate the length and direction of the transition. Text: When text is added, a new layer will be automatically

• Jasco EasyCam Pro, 19 Click on the Create button on the Main Screen to see the create options. : You can add a frame or edge to an image by selecting the option you wish, and then clicking A pply. (You can preview different options before settling on a particular one.) : You can "stamp" out a template of your image by selecting the shape you want to use, and then clicking Apply. : You can create customized calendars by inserting your image into a calendar template. Select the month, year, and style that you want, then click

• Jasco EasyCam Pro, 20 PhotoImpression provides four different printing options: • Standard Printing: prints one image per page. You can add a title, center the image and title, change the paper orientation, add a frame (a black outline) around the image, resize the image, and select the number of copies (Windows only) that you want printed. Additional options include Auto Rotate (the program rotates the image to best fit the page), Auto Crop (the program crops the image to maximize the print area), and Nudge (allows you to make sli

• Jasco EasyCam Pro, 21 1 How To Install NetMeeting (XP includes as standard) 1.1 For Windows 98/Me Users Click Start, point to Programs, point to Accessories, point to Internet Tools and then click NetMeeting. For Windows 2000 Users Click Start, point to Programs, point to Accessories, point to Communications, and click NetMeeting. 1.2 Click Next , type the appropriate information in the First Name , Last Name, E-Mail Address, Location , and Comments dialog boxes, and then click Next . NOTE: The Location and Comments information is optional. 1.3 Click

• Jasco EasyCam Pro, 22 1. How To Install MSN Messenger 1.1 For Windows 98/Me/2000 Users 1.1.1 Please log on to http://messenger.msn.com to download. After the installation package is downloaded to your computer, it will start installing MSN Messenger. All you have to do is follow the instructions. 1.1.2 After the installation is completed, click Start , point to Programs , and click Windows Messenger . 1.2 For Windows XP Users 1.2.1 Click Start , point to Programs , and click Windows Messenger . 1.2.2 After you run Messenger for the first time, you can add friends to your list and send instant messages. 2. How To Start With The Cam

• 23 Sensor CMOS with 300K Pixels Color Depth 24 Bits, 16.7 million RGB true color Interface USB V1.1 White Balance & Gain Automatic Exposure Automatic Focus Range Manual, 10cm~infinity View Angle 52° (diagonal) Aperture F/2.6 H/W Snapshot Yes Anti-Flicker Yes Video Output Resolution 640X480, 352X288, 320X240, 176X144, 160X120 Video Frame Rate Up to 30 fp

Related Products and Documents (Webcam):

Comparable Devices:

Similar Resources:

• Sony CMU-BR100 (2 pages) © 2011 Sony Corporation Printed in China4-276-434-11(1)Camera and Microphone UnitCMU-BR100InstructionsEnglishCautionPlease read these safety instructions to ensure your personal safety and prevent property damage.Owner’s RecordThe model and serial numbers are located on the product. Record these numbers in the spaces provided below.Refer to them whenever …

• Trust 110T (9 pages) TRUST 110T SPACEC@M Instructions when using for the first time Chapter 1. Uninstalling old drivers and devices (4.1) 2. Installing the driver and connecting (4.2) UK3. Installing the software (4.3) 4. Checking after the installation (5) !1 Introduction This instruction manual is for users of the TRUST 110T SPACEC@M. Basic knowledge of computers …

• EMEET C960 (8 pages) HD Webcam eMeet C960 取扱説明書..........................................................................................................................................................ウェブカメラの概要............................................................................................................................................... …

• D-Link DCS 5300 - Network Camera (24 pages) 10/100 FAST ETHERNET NETWORK CAMERADCS-5300Quick Installation Guide+Руководство по быстрой установке+Guía de Instalación Rápida+Guia de Instalação Rápida+快速安裝指南+Petunjuk Pemasangan Cepat+ …

• Canon VB-C50i/VB-C50iR (244 pages) CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, JapanU.S.A. CANON U.S.A.,INC. NEW JERSEY OFFICE100 Jamesburg Road, Jamesburg, NJ 08831 USACANON U.S.A.,INC. CHICAGO OFFICE100 Park Blvd., Itasca, IL 60143 USACANON U.S.A.,INC. LOS ANGELES OFFICE15955 Alton Parkway, Irvine, CA 92618 USACANON U.S.A.,INC. HONOLULU OFFICE 210 Ward Avenue, Suite 200 H …

• D-Link DCS-932L (7 pages) 5/9/2014 Cammy - free & easy IP camera monitoringhttp://www.cammy.com/guides/d-link-dcs-932l-guide 1/7DCS932LGuideDLink DCS 932LIntroductionThissetup guide will step you through the process of configuring yourDLink DCS932Lto work with Cammy.This camera is supported by …

Comments, Questions and Opinions: