Manualios.com

HP 5501B Operating And Service Manual

  • 5501B Lighting Equipment
  • ma2tRJfngTKYY
  • Operating And Service Manual
  • PDF / Adobe Acrobat Reader
  • 120

HP 5501B Manual Online:

3.55, 1826 votes
HP 5501B User Manual
HP 5501B User Guide
HP 5501B Online Manual

Text of HP 5501B User Guide:

  • HP 5501B, HP5501B Performance Tests 4-2 4-13. Procedure a. Connect the HP5501B to the HP5501A system (or any suitable dual DC voltage power supply such as the HP6255A) using HP10778B Power Cable as shown in Figure 4-1. HP5501B Power Connection b. On the HP5501B, set the exit shutter of the turret assembly to its open aperture position. c. Turn the ±15 Volt power supply on and wait until the READY indicator is on, not blinking. This should occur less than 10 minutes after power is applied. d. Using the Laser Power Meter, al

  • HP5501B Operation 3-14 3-12. Warmup Time Operating Notes • Allow a full 10 minute warmup period for the HP5501B. • Warmup completion is indicated by the READY LED on the HP5501B rear panel. • If warmup is not complete after 10 minutes, a failure may be indicated. • If the READY indication at the laser head is not convenient to use because of the mounting scheme, try

  • HP 5501B, HP5501B Adjustments 5-5 h. Apply power to the system power supplies. NOTE READY LED will flash rapidly for about 5 seconds. LASER LED illuminates followed almost immediately by emission of laser light. i. Adjust A1R12 (Figure 5-1) for 3.5 milliamperes ± 0.1 milliampere. If the current cannot be adjusted to this value, see Laser High Voltage Troubleshooting in Section 8. If the laser power output (as measured in paragraph 4-9) is not greater than 120 microwatts (at this current level), the laser assembly may require replacement. j. Record the laser tube curren

  • HP 5501B, HP5501B Installation 2-7 Observe the current and grounding requirements described below. 2-23. Grounding Considerations 2-24. In order to avoid ground loops, the laser head base should be the only connection to earth ground. To accomplish this, the outputs of the ±15 Volt power supplies used to power the laser head should be floating. The +5 Volt power supply output required for either the HP10740A based electronics or HP10781A Pulse Converters, should also be floating. Alternatively, any other single point earth ground connection can be used to satisfy grounding requirements. 2-25. Power Supply Requirements 2-26. Tab

  • HP 5501B, HP5501B Service 8-3 8-12. Safety Considerations 8-13. The following paragraphs contain warnings and cautions that must be followed for your protection and to avoid damage to the equipment. MAINTENANCE DESCRIBED HEREIN IS PERFORMED WITH POWER SUPPLIED TO THE EQUIPMENT AND WITH THE PROTECTIVE COVERS REMOVED. SUCH MAINTENANCE SHOULD BE PERFORMED ONLY BY SERVICE-TRAINED PERSONNEL WHO ARE AWARE OF THE HAZARDS INVOLVED (FOR EXAMPLE, FIRE AND ELECTRIC SHOCK). WHERE MAINTENANCE CAN BE PERFORMED WITHOUT POWER APPLIED, THE POWER TO THE EQUIPMENT SHOULD BE REMOVED. BEFORE ANY REPAIR IS COMPLETED, ENSURE THAT ALL SAFETY FEATURES ARE INTACT AND FUNCTIONING, AND THAT ALL

  • HP 5501B, HP5501B Installation 1-3 1-8. Manual Organization 1-9. This Service Manual is organized as follows: SECTION 1, GENERAL INFORMATION: covers Equipment Description, Manual Organization, Instruments Covered by this Manual, Safety Considerations, Equipment Supplied, Available Accessories, Specifications, Recommended Test Equipment, and Warranty Information. SECTION 2, INSTALLATION: covers Grounding Considerations, Power Requirements, Interconnecting Cabling, Operating and Storage Environments, Storage and Shipment, and Packaging. SECTION 3, OPERATION: provides operating information and covers Equipment Front and Rear Panel Features, Warm-up Time Considerations, and Prog

  • HP 5501B, Table of Contents v 1 GENERAL INFORMATION ...................................................................................................................1-2 1-1. Introduction..............................................................................................................................1-2 1-4. Equipment Description ............................................................................................................1-2 1-8. Manual Organization................................................................................................................1-3 1-10. Instruments covered by thi

  • Table of Contents vi 5 ADJUSTMENTS....................................................................................................................................5-1 5-1. Introduction ..............................................................................................................................5-1 5-3. Safety Considerations...............................

  • HP 5501B, HP5501B Installation 2-6 Table 2-1. Laser Head System Signal Chart Input Output Signal Name Function Source Destination A1J6-A Fused +15V Accessory +15V Operating Power Accessory Equipment A1J6-B Fused +15V RET Accessory +15V Return Accessory Equipment A1J6-C REF A1J6-D -REF System REFerence signal, equal to the difference in frequency between laser beam components F1 and F2. Accessory Equipment A1J5-A +15V External +15V Power Input Ext. Pwr. Sup. A1J5-B -15V External -15V Po

  • HP 5501B, HP5501B Service 8-46 8-148. Warm-Up Error Amplifier Troubleshooting 8-149. This procedure assumes the power amplifier is functioning properly. a. Set HEATER jumper to OFF. A3TP11 waveform (see Figure 8-20) changes to 0 Vdc. If yes, go to step b. If no, go to power amplifier servicing. b. Is A3TP15 voltage +0.2 to +0.6 Vdc? If yes, go to step c. If no, A3R18, R19 or U14 is faulty. c. Check A3R16 (SET TEMP potentiometer) to see if it is shorted. Short A3TP15 to TP11. Measure U14 (Pin 6). Does the voltage stabilize between -1.5 V and +1.5 Vdc? If yes, go to step d. If no,

  • HP 5501B, HP5501B Installation 1-4 1-14. Safety Considerations 1-15. The HP5501B Laser Head is designed to receive its power from a Safety Class 1 product. It is designed and tested in accordance with international safety standard IEC* 348. It is also a Class 1/ Laser product certified as conforming to U. S. National Center for Devices and Radiological Health Regulations 21 CFR ** 1040.10 and 1040.11. The instrument and the manual should be inspected and reviewed for safety markings and instructions before operatio

  • HP 5501B, Table of Contents vii 8-97. Dividers Ⓑ..............................................................................................................................8-32 8-99. State Machine Ⓕ....................................................................................................................8-33 8-105. Liquid Crystal Ⓓ.....................................................................................................................8-34 8-109. Photodiode and Amplifier Ⓔ..............................................................................

  • HP 5501B, HP5501B Service 8-1 8 SERVICE 8-1. Introduction 8-2. This section contains service information for the HP5501B Laser Head. Also included are safety considerations, theory of operation, block diagrams, schematic diagrams, component locators, and troubleshooting and repair procedures. Other useful service information also provided in other sections of this manual include: performance tests in Section 4, adjustments in Section 5, and exploded view illustrations and parts lists in Section 6. 8-3. Theory of Operation 8-4. T

  • HP5501B Installation 1-6 1-22. Recommended Test Equipment 1-23. The equipment required to maintain the HP5501B Laser Head is listed in Table 1-2. Other equipment may be substituted if it meets or exceeds the critical specifications listed in the table. Table 1-2. Recommended Test Equipment INSTRUMENT USE* CRITICAL SPECIFICATIONS RECOMMENDE

  • iv END PRODUCT LASER SAFETY CONSIDERATIONS The 5501B Laser Head complies with U.S. National Center for Devices and Radiological Health regulations 21 CFR 1040.10 and 1040.11. These regulations may also apply to the end product into which the 5501B will be designed. Care must be taken to insure that the end product complies with all a

  • HP 5501B, HP5501B Manual Changes 7-1 7 MANUAL CHANGES 7-1. Introduction 7-2. This section normally contains information required to update or backdate this manual to cover newer or older instruments with serial prefixes different than those shown on the title page. Since this manual applies directly to new HP5501B units having the serial number prefix listed on the title page, no change information is given here. Refer to INSTRUMENTS COVERED BY THIS MANUAL in Section 1 for additional important information about serial number coverage. 7-3. Newer Instruments 7-4. As engineering changes are made, newer instruments may have a higher serial number pr

  • HP 5501B, HP5501B Operation 3-18 Table 3-3. Modified HP10745A HP-IB Interface Program 0: gsb "warmup" 1: wrt 709,"0O6X" 2: wrt 709,"2V3O" 3: red 709,C 4: 0→E 5: "loop": E+1→E; if E=10;gto -3 6: wrt709,"1O2X3O" 7: red 709,X 8: if rds(7)<128;gto +2 9: 0→A; gsb "status" 10: (X-16)*6.23023e-6*C→X 11: fmt 1,f12.6 12: dsp X 13: gto "loop" 14: "status":rds(709)→B 15: if B>=64;gsb "check" 16: wrt 709,

  • HP 5501B, HP5501B Performance Tests 4-1 4 PERFORMANCE TESTS 4-1. Introduction 4-2. This section contains a performance test for the HP5501B Laser Head. A test record is included to record test results for future comparison. 4-3. RECOMMENDED TEST EQUIPMENT 4-4. Test equipment requirements are included in the following procedure. Detailed critical specifications for the required test equipment are contained in Table 1-2, Recommended Test Equipment. Any equipment that satisfies the critical specifications given in the table may be substituted for the recommended model(s). 4-5. TEST RECORD 4-6. Results of the performance test

  • HP5501B Service 8-14 Figure 8-9. Logic Clip Monitoring of Test IC U9 8-52. ASSEMBLY REMOVAL INSTRUCTIONS 8-53. Figure 6-1, the exploded view diagram in Section 6, shows the HP5501B assembly locations, provides access and removal information, and gives assembly part number references. 8-54. Access to the assemblies within the laser head is required to troub

  • HP 5501B, HP5501B Service 8-32 8-91. A3 CONTROLLER/REFERENCE BOARD AND A4 SAMPLER BOARD CIRCUIT THEORY 8-92. Introduction 8-93. Figure 8-18 (two sheets) shows the schematic diagram for the A3 Controller/Reference Board and the A4 Sampler Board. 8-94. The A1, A3, and A4 boards contain the electronics for the following portions of the Laser Head Block Diagram: • Power Amplifier • Warmup Error Amplifier • Photodiode and Amplifier • Liquid Crystal • Clock and State Machine • Subtracting Sample and Hold • Reference Receiver 8-95. Clock Ⓐ 8-96. The frequency of oscillator U10 is determined by timing components R8, C3, C7, and C8. For

  • HP 5501B, HP5501B Service 8-24 8-72. Procedure a. Apply power to the HP5501B. b. Wait until rear panel LED’s finish sequencing (see Table 3-1). The LED’s should reflect the following status. +15V SUPPLY UNBALANCE............OFF +15V POWER ON......................ON -15V SUPPLY UNBALANCE..............OFF -15V POWER ON ....................... ON +15V FUSE.......................................OFF READY .......................................ON -15V FUSE.........................................OFF LASER ON .................................ON c. If laser light is not emitted from the laser head, check that the exit shutter is open. Otherwis

  • HP 5501B, HP5501B Service 8-36 8-121. Reference Receiver Ⓛ NOTE A TILDE ("~") PRECEDING ALL SIGNALS INDICATES NEGATIVE-TRUE LOGIC. 8-122. The reference receiver consists of photodiode A3CR5, an amplifier A3U17, a transistor level shifter A3Q6, and associated passive components. The receiver amplifies and converts the sinusoidal output from A3CR5 to a square wave. When ~LTO (LOCKED TUNED OPTICAL) goes low, and the receiver amplifier has adequate signal level input, the receiver is enabled and provides a low TTL signal ~REF ON. During the warmu

Related Products and Documents (Lighting Equipment):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Lynx L24DWR User's manual & installation instructions lynx/l24dwr-H3K.pdf 07 Jun 2023 19
2 Asus rp-n14 Quick start manual asus/rp-n14-VHY.pdf 08 Feb 2023 144
3 Siemens Gigaset AL110 Operation & user’s manual siemens/gigaset-al110-V7T.pdf 13 Apr 2023 16 0.33 Mb
4 Sony VPLFX52L Quick reference manual sony/vplfx52l-RCC.pdf 26 Aug 2023 103 6.59 Mb
5 Stamina AeroPilates Performer 298 Owner's manual stamina/aeropilates-performer-298-15G.pdf 03 Dec 2023 19 0.44 Mb
6 Stelpro BF SERIES Operation & user’s manual stelpro/bf-series-QST.pdf 29 Jul 2022 4

Similar Resources:

  • weltico

    SKIMFILTRE A800

    (44 pages)
    SKIMFILTREBYWELTICOFR ... 2EN ... 8ES ... 14IT ..... 20DE ... 26NL ... 32PT .... 38WELTICO15 rue des Marais44310 ST-PHILBERT DE GRAND LIEUTel : +33 (0)2 40 59 95 95Fax : +33 (0) 2 40 59 94 [email protected] in France2 years warrantyPhotos non contractuelles.Non-contract photo.63682 …
  • RAB Lighting

    FXLED78

    (2 pages)
    FXLED78 INSTALLATION INSTRUCTIONS IMPORTANTREAD CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION …
  • Desisti

    Soft LED 2 Vari-White

    (8 pages)
    This Manual is applicable to Soft LED 2 Vari-White Revised August 2018 SOFT LED 2 Vari-White 120W LED SOFTLIGHT 90-250V 50/60 Hz (white light, with Tunable Correlated Color Temperature from 2.800 to 6.600°K) INSTRUCTION MANUAL MANUFACTURER REPRESENTATIVE ILT Italy S.r.l. Via Cancelliera # …
  • MAXSA

    44640

    (8 pages)
    1ASSEMBLY & OPERATING INSTRUCTIONS IMPORTANT: Read all instructions carefully before useABOUT YOUR SOLAR SECURITY LIGHTDuring the day, the solar panel included with this MAXSA Solar Security Light converts sunlight into electricity, recharging the pre-installed battery. Using this stored energy, the SMT LED lights turn on automatically at night when mot …
  • Vision & Control

    LDLF30x300-G525/24V/-a

    (32 pages)
    creating machine vision VISION & CONTROLInstructions for UseLDLF30x300-G525/24V/-aLED bar light, diffuse illumination,Luminous colour: Green - 525 nmInstructions for UseLDLF30x300-G525/24V/-aLED bar light, diffuse illumination,Luminous colour: Green - 525 nm999.995.616.10-en-1.0© Vision & Control GmbH 2019 …
  • kenall

    RESIDENCE MPWV Series

    (3 pages)
    www.kenall.com | P: 800-4-Kenall | F: 262-891-9701 | 10200 55th Street Kenosha, Wisconsin 53144, USA This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents found at www.kenall.com/patents. Content of specication sheets is subject to …

Comments, Questions and Opinions: