HP Designjet 3500cp Quick Start Manual

Text of HP Designjet 3500cp User Guide:

• HP Designjet 3500cp, Working with Media Removing a Roll from the Printer 3-32 5 Remove the old roll by pulling firmly on each end of the spindle, A then B. 6 Rest the old roll upright on the floor so that the media stop (A) is on top. Pull out the media stop A and the spindle. Pull out the endcap (B) from the other end of the old roll. NOTE:Alternatively if the media roll is very long, rest it horizontally on a table and unload the media on the table. 7 You have completed removing the old roll media from the printer. If you are not imme

• Working with Media Loading Roll Media 3-14 NOTE:Make sure the media lever is in the raised position. 3 Open the roll cover and pull out the media. 4 Position the media. 12'' / 305mm 42'' / 1067mm + 54''/1372m m = + 36''/915m m = + 50''/1270m m = 40 - 45 cm C472330a C472370

• HP Designjet 3500cp, Working with Media Installing a New Roll into the Printer 3-35 7 Insert the spindle so that the large media stop (A) is to the right and the small endcap (B) to the left. Push in firmly on both ends. Make sure the media remains flush against the media stop. The media must be positioned on the roll as shown above. A B 12'' / 305mm 42'' / 1067m m + 54''/1372m m = + 36''/915m m = + 50''/1270m m = 42'' / 1067mm + 54''/1372mm= + 36''/915mm= + 50&ap

• HP Designjet 3500cp, In the Advanced Properties window… Alternatively select a preset page size and skip the Postscript Custom Page size step. Finally, in the Postscript Custom Page Size window… Then select OK in all windows to print. Note: The maximum page size in Powerpoint is 60”x60”. So, if you would like a longer poster, you’re out of luck—use Illustrator instead. 1) Select Postscript Custom Page Size 2) Select Edit Custom Page Size 1) Enter Shortest Dimension 2) Enter Longest Dimension 3) Select Short Edge First

• HP Designjet 3500cp, Working with Media Unloading Sheet Media 3-43 Unloading Sheet Media 1 Wait until the appropriate drying time has passed (see page 3-45, Drying Time (Take Up Reel =off)). No drying time is necessary for some combinations of media types and print modes). 2 Press the Form Feed and Cut button 3 Gently pull the sheet from the printer. C4704024 Form Feed and CutCancel 12'' / 305mm 42'' / 1067mm + 54''/1372mm= + 36''/915mm= + 50''/1270mm= C472364

• HP Designjet 3500cp, Controlling the Overall appearance of a Print Printing Speeds and Print Quality 6-14 Print mode settings You can set the overall Print mode from the front panel. In general: ■ Choose Economy to print your images in the shortest time. ■ Choose Productivity to get a good combination of image quality and productivity. ■ Choose Photo to get the highest possible quality. You should print images in different modes to see which mode gives the best combination of throughput and quality for your application. The resolution at which your print will be printed is summarized in the table below. NOTE:The Economy setting enables you to print faster and so therefore is more

• HP Designjet 3500cp, Working with Media Loading Roll Media 3-18 d Take hold of the edges of the media now extending from the exit slot and pull the media toward you until taut. Then align the left and right edges of the media, so that they are flush with the edges of the roll. e When you have aligned the media lift the lever. f The printer checks that the media is aligned properly. If the alignment is successful the front panel displays: 12 Close the roll cover and press the ↓ key. Impom Impomui ioitruy Impomui ioitruy C4723127 after aligning C4704131 C4704016 Lift lever after aligning Close roll cover Continue--------->

• Working with Media Loading sheet media 3-40 Loading sheet media Which edge first? You can load a sheet in either portrait or landscape orientation. Unless using the Rotate option (see page 5-15, Rotating an Image), load the sheet in the same orientation as you have specified in your software. If printing a PostScript file, always load the sheet with the short edge first, e

• HP Designjet 3500cp, Working with Media Loading Roll Media 3-19 13 When you close the roll cover you have two options, depending on the status of the Take Up Reel a If the Take Up Reel is turned off the printer is now ready to print. NOTE:If you want to turn on the Take Up Reel, see page 8-12, Turning on the Take Up Reel. b If the Take Up Reel is turned on and you want to load the Take Up Reel proceed to the next step. 14 If your media is not straight or has been damaged press the ↑ key. If you want to continue use

• HP Designjet 3500cp, Section Page Removing a Roll ................................................................................................................................1 Installing a Roll..................................................................................................................................3 Loading Roll Media ...........................................................................................................................6 Loading Sheet Media .........................................................

• HP Designjet 3500cp, Working with Media Loading Roll Media 3-16 8 Press the media button and the media will be fed into the printer. 9 Press the ↓ key next to the front-panel display to indicate you are loading a roll. 10 Use the ↑ and ↓ keys until the display shows the type of media you are loading and then press the Enter key. C472353 C4704029 Sheet load ---------> Roll load ------------> Enter Previous C4704030 SELECT MEDIA Coated paper Previous Enter

• HP Designjet 3500cp, Working with Media Loading sheet media 3-41 3 Holding the media at its sides, align the right edge with the perforated line on the entry platen. When the media is fed into the printer as far possible the media button light comes on. 4 When you are satisfied that the media is positioned straight, press the media button. Only let go of the media when the printer begins to pull it in. 5 Press ↑ next to the front-panel display to indicate you are loading a sheet. 12'' / 305mm 42'' / 1067mm + 54''/

• HP Designjet 3500cp, Working with Media Installing a New Roll into the Printer 3-33 Installing a New Roll into the Printer 1 If an empty spindle is installed in the printer, open the roll cover and remove the empty spindle by pulling firmly on each end, A and then B as shown below. 2 Remove the new roll from its wrapping. 3 HP Heavyweight Coated Paper is the only media that is compatible with both the HP DesignJet CP Ink System and the HP DesignJet CP Ink System UV. Therefore, if you have changed the Ink System and the media you are loading is incompatible with the new Ink System, the printer will automatically reject the non-compatible me

• HP Designjet 3500cp, In the Advanced Properties window… Alternatively select a preset page size and skip the Postscript Custom Page size step. Finally, in the Postscript Custom Page Size window… Then select OK in all windows. 1) Select Postscript Custom Page Size 2) Select Edit Custom Page Size 1) Enter Shortest Dimension 2) Enter Longest Dimension 3) Select Short Edge First

• HP Designjet 3500cp, IMPORTANT: • If you have not printed to the plotter before, or you are not sure what may come out, DO NOT LEAVE THE PLOTTER UNATTENDED. • If your poster is not printing properly, and you don’t need to wait for it to finish the bad print, PRESS THE CANCEL BUTTON on the plotter to save ink and paper. • Remember the costs! o Coated paper - $100/roll o Glossy paper - $200/roll o Ink (CMYK) - $125/color o Repairs - $2000/technician visit • Check the printers on your own computers to make sure you are not printing normal printer jobs to the plotter. • Press

• HP Designjet 3500cp, Working with Media Loading Roll Media 3-13 Loading Roll Media To start this procedure you need to have a roll of media installed on to the printer spindle. See page 3-33, Installing a New Roll into the Printer. 1 Check the leading edge as it unwinds from the spool. If it is not evenly cut or if it is skewed (not perpendicular to the guides), continue with the next procedure. If the media is cut correctly go to step 3. WARNING The knife used in the next step is sharp. Be sure the printer’s wheels are locked. Keep fingers clear of the cutting path. Keep the knife away from children. 2 Trim the leading edge of the media roll only if it is not strai

• HP Designjet 3500cp, Controlling the Overall appearance of a Print Printing Speeds and Print Quality 6-16 Changing the print mode 3500CP Only Use the front-panel print mode key to toggle between the three print mode settings. Settings in your PostScript printer driver override the front-panel setting. Use your driver for setting the print mode of images sent from your computer. Use the front panel to set the print mode for internal prints. 3000CP Only Use the front-panel print mode key to toggle between the three print mode settings. If your software raster imaging proc

• Working with Media Loading Roll Media 3-17 11 Align the media. a When the front panel displays “Lower Lever”. Lower the media lever. b Wind the media stop in the direction of the arrow shown below. This is to take up any slack in the roll before aligning the media. c The front panel displays: C4704034 Lower Lever C4704130 roll cover n ue ----------> C4723128a Imp

• Working with Media Installing a New Roll into the Printer 3-34 4 Place the spindle vertically on the floor, with the media stop at the bottom. Remove the end cap from the top of the spindle, and slide the new roll onto the spindle. The leading edge of the media must wind clockwise as shown below. 5 Alternatively if the media roll is very long, rest it horizontally

More Instructions:

	HP Designjet 3500cp Quick reference manual 01-10-2022 116	DOWNLOAD
	HP Designjet 3500cp Operation & user’s manual 25-04-2023 342	DOWNLOAD
	HP Designjet 3500cp Service manual 05-12-2022 332	DOWNLOAD
	HP Designjet 3500cp Printing manual 22-08-2023 28	DOWNLOAD

Related Products and Documents (Plotter):

Comparable Devices:

Similar Resources:

• HP 750c - DesignJet Plus Color Inkjet Printer (32 pages) Company confidential. Murillo/Ravillo QRG. Edition 1. Freeze status: not frozen.This is the black on outside front coverThis is the yellow on outside front coveriHP DesignJet 700 andHP DesignJet 750C Plus PlottersQuick Reference Guide …

• HP Deskjet 600 (124 pages) HP DeskJet 600, 700, 800, 900 & HP 2000 Series PCL Developer’s GuideHewlett-Packard Vancouver SiteTo aid in HP PCL printer driver development for HP DeskJet 600/700/800/900 & HP 2000 Series printers …

• PSL MicroPMU (54 pages) 1 Quickstart Kit – Administration Manual - Revision 15 Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com MicroPMU Quickstart Kit Administrator Manual Revision 15 MicroPMU Quickstart Kit Administration guide for adding, removing, and managing MicroPMU d …

• MIMAKI UCJV300 (22 pages) UCJV300/150, CJV300 Plus series ID Cut GuideCongratulations on your purchase of an inkjet printer of MIMAKI (print & cut type).UCJV300/150, CJV300 Plusseries This " ID Cut Guide", describes the method for ID cut by using UCJV300/150, CJV300 Plus series and thesupplied software. Precautions and predefined settings are also described.Note• It i …

• HP Compaq Presario,Presario CQ5110F (8 pages) Volume Two 3-5Presario 700System Boards(w/o processor) Assembly Spare Part SystemConfigCodes486 System Board, 4 MB 004105004259171009-001 Note 1 HLU, HLV,HLW, HLX,HQA486 System Board, 8 MB 004093004842210063-001 Note 2 HQB586 System Board, P5, 8MB004378 187966-001 Note 3 HPS586 Syst …

• Roland CAMM-1 GS-24 (20 pages) Installation GuideWhat you need to read before using the machineInstallation Guide (this document)This manual contains information on handling precautions, installation instructions, and preparations before use. This manual must be read rst.Startup Guide (web page)This is an online manual that must be read after this guide.It contains instructions about w …

Comments, Questions and Opinions: