LeapFrog Xeed Manual 

Text of LeapFrog Xeed User Guide:

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 23 The second step is to click on the “Add” button in the left lower window. After pressing this button the “FFF window” pops up where you can select a standard print profile in the drop down menu. Leapfrog is continuously testing and developing Profiles with standard print settings in order to establish the best print results and therefor might send you additional Profiles applicable to your printer which you can add to your software by clicking the “Import” button in the FFF window. At the time of writing we developed three Profiles: 1. “Leapfrog_Xeed ABS_BackExtruder.fff�

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 18 2.4 Uploading your 3D model. Now that you have loaded the filament and the printer is on, it is time to load the model that you wish to print. This section explains the steps to follow when uploading your 3D models. Go to the “Status” tab in the upper left corner. . There are two ways to upload your models to the Xeed. You can use a portable USB device, which you can insert in the back of the printer or you can use a network connection that allows you to connect your Xeed with your computer through your network. 2.4.1 Uploading a model from a USB device To up

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 4 1. Installation The following steps are steps you only have to follow when your brand new Xeed arrives at your doorstep for the first time. Please follow each step thoroughly to make sure the installation will be successful and you will find yourself to be a member of the leapfrog eco-system. This section contains the following: 1.1 Unpack o How to unpack your Xeed and where you plug the power cord and usb cable.

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 6 2. Printing The following steps are general steps which you need to follow when making a 3D print with your Xeed. 2.0 Initial setup 2.1 Turning on your printer and loading your filament o How to turn on the Xeed and load the filament for printing 2.2 Heating the extruders o How to manually preheat your extruders 2.3 Manually controlling your Xeed o How to control the movements of your Xeed manually 2.4 Uploading your 3D model o How to connect with your Xeed to upload new models 2.5 Making your print o How to make the Xeed print

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 25 The final step after saving your settings is to press the “Prepare” button in the left lower window to generate, save and preview your G-code. The G-code can now be uploaded by your printer through a computer connection as explained in paragraph “2.4.2. Uploading a model from your computer” and is ready to be printed!

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 12 //Level bed Before we start to print we want to make sure that the bed is levelled. Under the "Control" tab in LilyPrint there is a "Xeed" section. Press the “LEVEL BED” button to start the sequence. It will probe 5 spots on the bed and make sure it is levelled. This can take up to 4-5 sequences.

• Leapfrog 3D Printers - Manual Xeed 24 With step three you can choose your own settings to optimize print results for your personal 3D models and start exploring the 3D printing boundaries. FFF Settings shown in the picture below allow you to easily select “Medium” or “High” print quality. Be noted that printing in Hi

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 2 Dear customer, Congratulations with the purchase of your very own Leapfrog Xeed 3d-printer. We want to help you make your first 3d-print with the very first Leapfrog stand-alone printer. To make your first impression the best one possible, we want to provide you with our manual which will take you through the first steps and make you more familiar with your Xeed. For maximum 3D-print pleasure. It is possible that after reading this document or wh

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 16 If you want to load filament quickly then push the “QUICK LOAD” button which automatically guides the filament all the way to the extruder head. Before pressing “QUICK LOAD” it is best to open the filament drawer fully. This allows for you to check if the filament is still being loaded and reduces any risk of jamming due to resistance in the cables. The process takes about one minute, where filament is first loaded quickly and slows down in the last half not to clog the nozzle. ONLY

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 7 2.0.1 Initial setup Before you can use the Xeed, we have to go through the initial setup. This will make sure the Xeed is connected to the network and is up-to-date. This will allow you to access the Xeed through a LAN network later, which allows remote control of the printer, remote upload from Gcode files and more. For the setup you will need the following: -USB keyboard -USB mouse -Ethernet cable to Xeed with Internet access Plug in the keyboard, mouse and Ethernet cable at the back of the Xeed. Turn on the Xeed by switching the

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 9 //Update LilyPrint LilyPrint has an update feature, we will run this to make sure that it is up-to-date before we start. Click on the System menu in the top bar of LilyPrint and select "Update LilyPrint", confirm the notification to start the update. Make sure you have Internet connection! (If there is no system menu and it asks for a login, username: "lily"; password: "lily". Refresh browser with F5 if the login does not show right away.) A p

• Leapfrog 3D Printers - Manual Xeed 30 3.2. Updates We will be able to remotely send updates to your Xeed which will be announced through the “Updates / notifications” button. If you receive an update go to “Configuration” and select “System upgrade” or “Firmware upgrade” as shown below and follow any given instructions.

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 21 2.4.3 Start a print It is very easy to start a print. Just press on the printer icon on the model and the printer will start the GCODE. In the “State” field it will show the progress, time elapsed and time left(estimated). 2.4.4 The terminal The terminal tab shows all the communication between the printer and the software. This is useful if there is an error or the printer is not working. Advanced users can also send manual GCODE commands to the printer on this tab.

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 31 3.3. Troubleshooting Although we work very hard on minimizing possible troubles some might occur while or even before operating the machine. In general these troubles can be tackled quite easily. We listed 5 possible troubles that could occur and how you can to tackle them. 3.3.1. Transporting, Unpacking and Positioning the Xeed Transporting Think carefully before delivery or (local) pick up how to transport your Xeed to its final destination. Xeed weighs around 75KG with outer dimensions: 900 x 580 x 640 mm. Xeed + Crate + filament weighs

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 8 In the pop-up that appears note the IP Address under the IPv4 section, you can use this later to access LilyPrint from your own computer in the same network. To connect to a WiFi network, left click on the network icon and select the wifi network. In the pop- up enter the WiFi password. (If it asks for admin password it is "lily").

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 19 2.4.2 Uploading a model from your computer To upload a model from your computer you will have to connect your Xeed to your network. This can be done in two ways, either by Wi-Fi or using an Ethernet cable. For instructions see the Initial Setup chapter of this manual. It is really easy to access LilyPrint via your browser, just enter the IP number you have noted down from the initial setup and input that into your browser. Make sure you are in the same internal network as the printer (for example both “192.168.0.X”). You will have access to exactly the same controls as

• Leapfrog 3D Printers - Manual Xeed 28 3.1 Need support? Of course it is possible that you run into something that was not explained in this document. Here we explain you what to do in such a case.  Go to https://www.lpfrg.com/support/.  If you cannot find the solution to your problem at FAQ, Knowledgebase or on our Forum, you can alwa

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 27 3. Support In case anything in the manual is unclear and you still have some remaining questions or if you are experiencing some kind of problem with your Xeed or your prints we are there to help you. This section explains to you how to contact us with your questions so that we can help you as soon as possible. This section contains the following: 3.1 Need support? o How to contact the Leapfrog support team

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 14 2.2 Extruding filament The software that is used to control the Xeed is called LilyPrint. In the next screenshot we have outlined real brief what all the tabs in the main screen. During this manual we will explain each option and its functions starting with the heating of your extruders. Status – Printer status and upload files Temperature – Control and set temperature. Temperature graph Control – Control the printer manu

• Leapfrog 3D Printers - Manual Xeed 5 1.1 Unpack In this step we will show you how to unpack your Xeed when it arrives at your doorstep. Before you start, make sure that you have cleared a spot where you want to place the printer. We advise you to not place the Xeed next to a window or at a place where it is draughty.  Unscrew the 4 screws in the b

• Leapfrog 3D Printers - Manual Xeed 3 Table of content 1. Installation 1.1 Unpack Page 5 2. Printing 2.1 Turning on your printer and loading your filament Page 7 2.2 Heating the extruders Page 9 2.3 Manually controlling your Xeed Page 11 2.3.1 Movements Page 11 2.4

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 10 When the update is complete reboot the system by clicking on the System Menu and selecting Reboot. (Update regularly to get new features!) LilyPrint is now updated to the latest version.

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 32 3.3.3. Filament slipping Before loading the filament make sure that filament on the spool is free and not entangled which can occur after removing and replacing the spool. Take the time to make sure that the filament is inserted properly in the driver gear. Depending on the spool size it might help to place it upside down in the drawer so that filament rolls of from the bottom instead of the top. Push the filament manually as far until

• LeapFrog Xeed, Leapfrog 3D Printers - Manual Xeed 15 You can notice that the temperature graph of the front extruder shows the current and target temperature. To load your filament into the extruder you can use the “EXTRUDE” button, located on the control tab. Make sure your filament is placed correctly in the filament drawer and that your extruders are heated to the correct temperature for your filament type. Select the correct tool that you want to extrude. After pushing the Extrude button, the filament will be guided through the tube towards the extruder head an

More Instructions:

LeapFrog Xeed Manual  21-09-2023 31

DOWNLOAD

Related Products and Documents (3D Printers):

Comparable Devices:

Similar Resources:

• Rokit AEP Series (45 pages) AEP-CHS-20191117 1 AEP SERIES USER MANUAL …

• TierTime UP300 (2 pages) H. Printer Description[Front]Power SwitchFilament BayRight Side HandleTop LidEthernet SocketUSB PortPower Socket[Right][Back]Quick Start Guide300Tiertime Corporation 1765 Landess Ave. #338Milpitas, CA 95035, USATel: +1 888 288 6124www.tiertime.com@Tiertime to share your printsSales Department: [email protected]@tiertime.comFor Local Support:Contact y …

• SeeMeCNC Artemis (11 pages) SeeMeCNC GuidesConfiguring ArtemisConfiguring your Artemis printer. Connecting it to your network and getting everything dialed in forsuccessful printing.Written By: SeeMeCNCConfiguring Artemis© 2018 seemecnc.dozuki.com/ Page 1 of 11 …

• RAISE 3D Pro2 Series (31 pages) Quick Start GuidePro2-Series 3D Printer* Please review this entire guide before operating the printer.Pro2 Pro2 Plus01 0203 04 05 0607 08 09 1011 12 13 1415 16 17 1819 20 21 2223 2624 25 …

• FELIXrobotics FELIX 3.0 (65 pages) User Manual FELIX 3.0, 3d printer VERSION 8 Copyright Information This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of FELIXrobotics BV. FELIXrobotics BV Gessel 4a 3454MZ, de Meern The Netherlands …

• HP DESIGNJET 3D (12 pages) 1HP Designjet 3D Material BayAssembly InstructionsHP Designjet 3D Material BayInstructions d’assemblageHP Designjet 3D Material BayMontageanleitungenHP Designjet 3D Material BayIstruzioni di assemblaggioHP Designjet 3D Material BayInstrucciones de montajeHP Designjet 3D Material Bay組立説明書HP Designjet 3D Material Bay组装说明CQ708-90001CQ708-900 …

Comments, Questions and Opinions: