Hitachi AJ-CE series Operation Manual
|
Hitachi AJ-CE series, 9. Calibrating the Balance Since electronic balances are affected by gravity gravitational acceleration, they produce different values in various locations. Therefore, before use, balances must be calibrated at the location where they are installed. Calibration is also required after long periods without use, or if a balance begins to produce inaccurate values. Calibration of a balance, or "span adjustment," is required to produce accurate measurements. 9.1 Calibration of AJ-CE Series Applicable models: AJ-220CE, AJ-420CE, AJ-620CE, AJ-820CE, and AJ-1200CE(for AJ- 220CE.420CE, and 1200CE, applicable when the lock switch is off.) >£• Span adjustment should be
Hitachi AJ-CE series, 9.3 GLP-compliant print At calibration, the AJH-CE Series enables printing in a format compliant with GLP. Set the function to the GLP print support ([EL u.L P I]) side, then connect the balance to a printer or other equipment. When calibration is complete, the balance prints out the format illustrated below. Since only items are printed, the data should be entered manually by the person who conducted calibration. ^Reference: "4.2 Description of Functions" (Page 13) "
Hitachi AJ-CE series, Do Not Apply Force • Avoid applying excess force or impact to the balance. • Place the sample to be measured on the balance carefully to prevent breakage or malfunction. 0 Do Not Use • Do not use the balance in a location were it may be subjected to abrupt changes in ambient temperature or humidity. • Accurate measurement may not be obtained. • Optimum operations occur when ambient temperatures range from 10°C to 30°C, and less than 80% relative humidity. Do Not Overload • Do not use the balance when [Q -Err] (Overloaded) is displayed. • Take down the loaded sample immediately to prevent breakage or malfunction. 0 Do Not Use • Do not use the balance in
Hitachi AJ-CE series, 200009M11 High-Precision Tuning Fork Electronic Balance AJ-CE/AJH-CE Series Operation Manual A3 \Zoo os IMPORTANT • To ensure safe and proper use of the balance, please read this manual carefully. • After reading this manual, store it in a safe place near the balance, so you can review it as needed. V ; VlBRA SHINKO DENSHI CO., LTD.
Hitachi AJ-CE series, 2.2.2 Names and Functions of Operating Keys Operating Key Function On/off key Key to turn on/off the unit power Memory key [Brief press] [Brief press] initiates print or output. saves the settings of the number of pieces or percentages (%), or the limit value when using the limit function. Set key [Brief press] [Continuous press] starts setting the number of pieces or percentages (%). starts setting the limit value when using the limit function. Function key [Brief press] [Brief press] [Brief press] [Continuous press] [Longer continuous
8.3 Setting up Limit Values by Inputting Values (cont.) 8 Opening the value input screen aaaaoo't Press the | Zero/Tare | key. Follow the same procedure as in "Step 2." 9 Setting the upper-limit value \ I / ~V'T V" 1 V33WSSB Follow the same procedure as described for the lower-limit value and enter the upper-limit value. D y 10 Saving the upper-limit v
Hitachi AJ-CE series, it Key Points of the Prcedure ir 1. While samples are being saved, the value indication disappears temporarily, and only the [M] mark flashes. If the balance is affected by wind or other vibrations during this process, the saving time may be prolonged. 2. If [L " II r r ] appears briefly, it indicates one of the following states: (1) The weight of the reference sample is insufficient. For the limit weight that can be saved (% limit weight), please refer to "13. Specifications," on page 41. (2) While
Hitachi AJ-CE series, Key Points of the Procedure it The following applies equally to all the measurement modes for weight measurement, counting, and percentages. 1. After the balance is switched off, there is still enough current to display [ * ]. This indicates that the AC adapter is connected to an electrical outlet, but that the balance is turned off. When the balance is switched on again, [ * ] will disappear. SKIf the balance is running on batteries and the unit is switched off, the display does not display [ * ]. 2. The bar graph shows the current load status with respect to the capaci
Hitachi AJ-CE series, 9.2 Calibration of AJH-CE Series Applicable models: AJH-220CE, AJH-420CE and AJH-620CE JK Span adjustment should be performed with the balance installed perfectly level and without any load on the measurement pan. 1 Invoke the span-adjustment function. S.R. CRL U Hold down. Release your finger. Hold down the | Function I key, then release your finger when the display switches from [F u n c ] to [5. R. II f 2 Start span adjustment. 5.R CRL -. I / v I / CRL. 0 CAL 0) Press the Function key while holding down the Zero/Tare key. Release both fingers at the same time. Press the | Function | key while holding down the | Zero/Tare] key, then release both fingers simultaneou
Hitachi AJ-CE series, 10.4.5 Result of judgment when operating the balance with the limit function (S1: one character) S1 L G H (SP) Code 4CH 47H 48H 20 H Description LO (LOW) OK (GOOD) HI (HIGH) No limit value specified 10.4.6 Status (S2: one character) S2 S U E (SP) Code 53H 55H 45H 20H Description Data stable Data unstable Data error (data other than S2 is invalid.) [o - E r r ], [ u -Err] No status specified 10.5 Input Commands Users can control the balance remotely by transmitting commands from an external device. Two types of control commands are available: (1) Ins
Hitachi AJ-CE series, 3. Basic Operations 3.1 Installation 1 Positioning the measurement pan First, mount the pan base on the main unit of the balance and place the measurement pan on top of it. Be sure to mount the pan base in the correct direction, as illustrated below. 2 Securing the exact level of the balance Position of air bubble in the level Turn the adjusters until the bubble rests in the center of the red circle on the level. Round-pan type: total of two adjusters, one on either side at front Square-pan type: total of four adjusters, one on either side at front and rear <Caution> Use caution when operating the adjusters on the square-pan
Hitachi AJ-CE series, CONTENTS 1. Precautions on the Use 2 2. Names of Component Parts ....5 2.1 Main Unit 5 2.2 LCD Indicators and Operating Keys 6 3. Basic Operations .....8 3.1 Installation 8 3.2 Operation Check 9 3.3 Operation for Tare Subtraction 10 4. Functions 12 4.1 Setup and Checking of Functions . 12 4.2 Description of Functions 13 4.2 Description of Functions (cont.) 14 4.3 Interface Section 14 5.1 Switching Units of Measurement... 15 5.2 Setup of Units of Measurement (Only when the lock switch is off) 15 6. Counting Pieces 17 6.1 Sampling 17 6.2 Increasing the Counting Accuracy (Memory Update Method) 19 7. Measuring Percentage 20 8. Limit Function 22 8.1 Limit Function Setup 22 8.1
Hitachi AJ-CE series, 10.2 Connection between Balances and Personal Computers ••• Sample connection with an IBM-PC/AT compatible ••• RXD TXD GND IBM-PC/AT compatible D-SUB9P TXD RXD GND DCD RTS CTS DSR DTR 3 2 5 1 7 8 6 4 -^ *—. • •—•* 4 Balance DIN5P 3 4 5 Sample connection with PC9801 ••• TXD RXD GND DCD RTS CTS DSR DTR PC9801 D-SUB25P 2 3 7 8 4 5 6 20 ». 4 d Balance DIN5P 3 4 5 RXD TXD GND 33
Hitachi AJ-CE series, Calibrating the Balance (cont.) 4 Calibrating the capacity point \ / o n \ /-. / yCfi L Load the calibration weight in the center of the balance. The display flashes, indicating that capacity point calibration is in progress. 5 Terminating the span adjustment on F.S I N ' I N > GAL When the calibration of the capacity point is finished, the original measurement mode is restored. 0 - | - | - I F EOO.no Gig it Key Points of the Procedure it 1. Pressing the | Function | key in Step 2 interrupts the span adjustment and returns you to t
8. Limit Function The limit function judges measurements according to a limit value saved in the balance. The function shows the judgement result by displaying the [M] mark as either HI (excessive), OK (appropriate), or LO (insufficient). This function is very useful when discriminating between conforming and nonconforming articles. It is also useful when measuring a given constant quantit
Hitachi AJ-CE series, 11. Operating the Balance with the Battery This function can be used only when the balance is battery-operated. 11.1 Specifications ;• Built-in nickel-cadmium battery • Charging time: Approximately 12 hours • Drive time: Approximately 32 continuous hours • Number of charge/discharge cycles: 300 or more 11.2 Charging Method JSWhile the balance is battery-operated, [Qni] stays on. The indicator flashes [£3] (charging required) when battery capacity decreases. If the balance flashes [£2]. charge the battery by following these steps: (1) Connect the dedicated AC adapter to the balance. (2) Turn the balance off.
5 End of calibration of weighing capacity point CAL CRLoFF Display switches to [l_ R Lo h h ] to indicate that adjustment of the weighing capacity point is complete. 6 End of span adjustment CAL b u 5 b' E n d. Return the calibration knob back to the [For Use] position. To do so, slowly turn the knob until the internal mechanism engages with a click. The balanc
Hitachi AJ-CE series, 4.2 Description of Functions Item Bar graph display Limit function n limit ted nly whe s activa 1% nT ° Co c b condition Judgement range Number of points for judgement Auto-zero (zero-tracking) Auto power-off Respo Stability nse speed parameters Interface Setup measur disp of units of sment to be layed" 1 Register selected measuring units with | Function key. Set Value 1, b.0. ESEL E I.L~o. EEL , E'5'.P .. El. HO s: HP. S r'E S. Sd. '1. IF. d I 'D. U. 8'SS.u. n u * I *0 / 1 •k 1 E !~l U & 1 t t (-/ U * 1 n u * 1 0 t 1 E *3 '-/ 5 / I *,£' 3 H 0 -i5r ,' E •A-1 D 1 -A-2 / S' IS IS i n i i 18 r-i IR Ib IE Id IE Descriptio
10.4.3 Numeric data Six-digit numeric format: (D1-D7: seven characters) Seven-digit numeric format: (D1-D8: eight characters) Six-digit numeric format for model provided with an auxiliary scale interval: (8 characters, from D1 to D8) Seven-digit numeric format for model provided with an auxiliary scale interval: (9 characters, from D1 to D9) D1-D7 (D8) 0-9 • (SP) / Code 30H-39H 2EH 20
Hitachi AJ-CE series, 3.2 Operation Check 1 Turning on the power When the balance has the AC adapter connected, it displays [ * ]. Pressing the | On/Off | key The display section lights up, and the balance is ready for operation. 2 Checking the display -Kn--m- OIIIIIIIIIIIIIIIIIIIF 4HI CAL p cs # Check to see if the display has any missing indications or unlit parts. A few seconds after startup, the indication is reset to zero. 3 Switching the measurement mode 0.0 0 Qg 0.00 C3 Press the | Function"] key. Each time the key is pressed, the unit of measurement changes, as indicated. balance is shipped from the factory with the following switching sequence: [g] -»
Hitachi AJ-CE series, 5. Switching Function for Units of Measurement Pressing the | Function] key allows the user to switch the unit of measurement to [g], [ct], [%], and so on. Up to five different units can be registered for use only when the function key is properly set on a balance for which the lock switch is off. 5.1 Switching Units of Measurement Switching the units of measurement to be displayed Press the [ Function | key. Each press advances through the units of measurement to be displayed. s&The balance is shi
Black & Decker BK60W Scales Original instructions manual
BK60W |
Magnum TE100 Scales Quick reference manual
TE100 |
Kompernass KH 808 Scales Operating instructions manual
KH 808 |
KERN FTB Scales Service manual
FTB |
Transcell Technology tcs3t series Scales Operation & user’s manual
tcs3t series |
A&D GF-1200 Scales Instruction manual
GF-1200 |
MasterCool 98310 Scales Operating instructions
98310 |
KERN FCE 3K1N Scales Operating manual
FCE 3K1N |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Prestigio | MultiPad PMP7070C3G | Technical service manual | prestigio/multipad-pmp7070c3g-B3O.pdf | 13 Sep 2023 | 34 | |
2 | Hand Held Products | 3800PDF | Specifications | hand-held-products/3800pdf-L1X.pdf | 30 Jun 2023 | 2 | 0.07 Mb |
3 | NVX | XBTL6 | Operation & user’s manual | nvx/xbtl6-2IO.pdf | 27 May 2023 | 12 | |
4 | Hitachi | RAK-50PPA | Installation manual | hitachi/rak-50ppa-962.pdf | 22 Oct 2023 | 2 | |
5 | Aluratek | ADMPF110 | Product reference card | aluratek/admpf110-8X8.pdf | 11 Jun 2023 | 1 | 1.36 Mb |
6 | Asus | Rampage IV GENE | Quick start manual | asus/rampage-iv-gene-9Z2.pdf | 17 Apr 2023 | 14 | 1.83 Mb |
Fobitec
- 1 - SC-A10 Manual User SC-A1 Advanced weighing equipment with ABS or INOX finish, backlit LCD display with 3 numeric display fields and alphanumerical keyboard. 2017-02-14 COMPLETE USER MANUAL
…
SC-A10(24 pages) |
Tree
SPECIFICATIONS Model number Capacity Division MSS-150 150lb 0.05lb MSS-330 330lb 0.1lb Platter / Tray 12.3X12.8inch/315×325mm Net/gross weight 2.1 kg / 3.1kg 4.6lb/ 6.8lb Package Standard carton: 515x415x120 (mm3) 5 Units in one box: 640×430×530 (mm3) Operating Temperature Optimum: 15-30℃ (62-90f) Indicator Power source 4×AA Batteries …
MSS-150(3 pages) |
RADWAG
Start up GuideAnalytical and Precision Balances Inicio rápidoBalanzas analíticas y de precisiónIMMB-04-02-04-22-EN-ESAnalitycal Balances: Balanzas analíticas:• AS X2 PLUSPrecision Balances:Balanzas de precisión:• PS X2• PS X2.M• WLC X2
…
AS X2 PLUS(24 pages) |
HAEGER
Digital Kitchen Scale / Balança Digital de Cozinha Balanza Digital de Cocina / Balance Digital de Cuisine User instructions / Instruções de uso Instrucciones de uso / Mode d’emploi Dark Glass * KS-005.007A
…
Dark Glass(20 pages) |
Silvercrest
Digital Kitchen ScalesOperating instructionsDigitális konyhamérlegHasználati utasításKuchyňská digitální váhaNávod k obsluzeDigital Kitchen ScalesDigitálna kuchynská váhaNávod na obsluhuDigitalna kuhinjska vagaUpute za upotrebuDigitale KüchenwaageBedienungsanleitungKOMPERNASS GMBH · BURGSTRASSE 21 · D-44867 BOCHUMwww.kompernass.comID-Nr.: K …
KH 1159(8 pages) |
KERN
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: [email protected] Tel: +49-[0]7433- 9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Betriebsanleitung Operating manual KERN MGD Version 1.0 2017-07 MGD-BA-de-1710
…
MGD Series(14 pages) |
Weber Grill SUMMIT 56568Weber SUMMIT 56568 User Guide (Doc Type: Grill Owner's manual) SUMMIT 56568, 32 |
Fujitsu Siemens Computers Server SPARC Enterprise M5000Fujitsu Siemens Computers SPARC Enterprise M5000 Server Operation & user’s manual SPARC Enterprise M5000, 162 |
PhaseOne Digital Camera P 25PhaseOne P 25 User Guide (Doc Type: Digital Camera Reference manual) P 25, 108 |
Cinecta Camera Accessories MX-1PDF Guide (@239F51), Cinecta MX-1 Camera Accessories (Sunday 10-09-2023) MX-1, 4 |
Parkside Drill PABS 12 B2Parkside Product Guide: PABS 12 B2 PDF Operation and safety notes - K79R19 PABS 12 B2, 25 |
MicroE Systems Recording Equipment Dual Axis Averager Mercury 3000SiDual Axis Averager Mercury 3000Si Installation and reference manual - 6B2KX2 Dual Axis Averager Mercury 3000Si, 27 |
Compaq Network Hardware RA8000Compaq RA8000 Network Hardware Quick setup manual RA8000, 16 |
Insignia LED TV NS-55D440NA14NS-55D440NA14 (LED TV ePDF User Manual, #2D693U) NS-55D440NA14, 2 |
Bosch Analytical Instruments GLM Professional 80 Plus R60Bosch GLM Professional 80 Plus R60 Analytical Instruments Original instructions manual GLM Professional 80 Plus R60, 319 |
LEGO Game 31013LEGO 31013 Game Instructions manual 31013, 32 |
Coby Flat Panel TV TF-TV1901PDF Manual (@95T4XL), Coby TF-TV1901 Flat Panel TV (Thu 08.2023) TF-TV1901, 1 |
MK Cordless Saw -1080Owner's manual for MK -1080 Cordless Saw -1080, 22 |