ARC Audio IDX Manual And User Manual

Text of ARC Audio IDX User Guide:

• ARC Audio IDX, XEQ MANUAL AND USER GUIDE 3-WAY CROSSOVER WITH SUB SONIC FILTER 7-BAND EQUALIZER WITH DIRECT SUB INPUT IDX Variable Sub Phase Shift Sub Sonic Filter Fully Variable Band Pass Crossover 8 Volt RMS Output Independent Front and Rear Inputs Output Clip Indicator for Easy Gain Setting 4-Layer PC Board with SMT Devices Variable Sub woofer Crossover Variable Sub woofer Crossover Front panel Sub output level control 8 Volt RMS Output Direct "Sub Input" Input Clip Indicator for Easy Gain Setting 4-Layer PC Board with SMT De

• ARC Audio IDX, Introduction Welcome to the Arc Audio family of performance signal processors. A blend of Arc Audio's lengthy experience in performance car audio design combined with our highly skilled engineering staff. You are now the proud owner of the IDX or XEQ. A unique combination of the highest quality analog components and precision engineering. Whether you are a competitor or simply enjoy faithfully reproduced music, you will definitely appreciate how these products make your system sound. These components aren't the easiest to understand and use. They require a good understanding of audio and the terms and language used to describe it.

• ARC Audio IDX, Installation Information 1. The XEQ needs to be installed in the signal path between your source unit and your external amplifier(s). 2. Physically mount the XEQ near the drivers listening position. Make sure the EQ is kept clean, cool, and dry. Don't mount it under a cup holder or in a storage box were it will be covered with the stuff that always seems to collect in our cars. 3. . Hook up +12 volt power, ground, and remote turn-on. Make sure the ground is perfectly clean and tight. Remove all the paint and under coat before you screw it down. Don't trust the stock ground. Make a new one. 4.

• ARC Audio IDX, 1. Front Output: Simply connect to the amplifier driving the front speakers. This is a full range output so if you plan to run it hard you should use a crossover at this point. 2. Rear Output: Just like it sounds, this is connected to the rear amp. 3. Input: Main Input should be a full range signal from the head unit. If you are using the Sub Direct Input the signal could be crossover but the EQ will function better if you feed it a full range signal. 4. Sub "Direct Input": This is where things get a little tricky. If your deck has a sub woofer output with any kind

• ARC Audio IDX, XEQ Optional 2-WAY With FADING FRONT and REAR 7 XEQ Signal to Noise Ratio (A-Weighted) >100dB THD @ 8.0V Output 0.005% Channel Separation >75dB Sub Woofer Crossover 45Hz-150Hz 12dB/Octave Input Impedance 15K Ohms RMS Output @ 1KHz 9.0 Volts Frequency Response 20Hz-30KHz EQ Frequency Range @ 50Hz 100Hz 275Hz 770Hz 2.2KHZ 6.0KHz 16.8KHZ +/- 12dB, Q=1.38 +/- 12dB, Q=1.20 +/- 12dB, Q=1.25 +/- 12dB, Q=1.18 +/- 12dB, Q=1.08 +/- 12dB, Q=1.10 +/- 12dB, Q=0.98 XEQ SPECIFICATIONS XEQ IDX XEQ 8

• Introduction Welcome to the Arc Audio family of performance signal processors. A blend of Arc Audio's lengthy experience in performance car audio design combined with our highly skilled engineering staff. You are now the proud owner of the IDX or XEQ. A unique combination of the highest quality analog components and precision engineering. Whether you are a competitor or simply

• ARC Audio IDX, Installation Information 1. The IDX needs to be installed in the signal path between your source unit and your external amplifier (s). 2. Because of it's small size the IDX can be mounted almost anywhere. The chassis is designed to fit a 1/2 DIN opening. however it will work just as well under a seat or in the trunk. For easiest tuning mount it near the drivers listening position. Make sure the Crossover is kept clean, cool, and dry. Don't mount it under a cup holder or in a storage box were it will be covered with the stuff that always seems to collect in our cars. 3. . Hook up +12 volt power, ground, and remote turn-on. Make sure the ground is perfectly clean

• ARC Audio IDX, 1. Front Input: This is the default input. If you are using one input (2 CH.) connect your RCAs here. 2. Rear Input: Use the rear inputs for 4-channel operation. In this configuration you can have faded front and rear front your hear unit. 3. Front Output: Front output in name only. If you're using the IDX in 3-Way this will be your High Pass x-over. This is a High Pass only crossover. 4. Rear Output: The rear output can be set as High Pass, Low Pass or Band Pass. To use the Band Pass mode you will need to set both High Pass and Low Pass switches on top of the unit. With both turned on the output will switch to Band Pass. Note: For this to work the High Pass will have to be se

• X10 OFF 90Hz X 1 = 90Hz X10 OFF 90Hz X 1 = 90Hz 2-WAY FADING FRONT AND REAR NOTE: THE CONTROL POSITIONS SHOWN ARE ONLY ONE SUGGESTED CONFIGURATION. YOUR SYSTEM MAY REQUIRE DEFERENT SETTINGS. 15 IDX X10 on 500Hz X10 = 5000Hz X10 OFF 90Hz X 1 = 90Hz X10 ON 500Hz X 10 = 5000Hz IN BAND PASS MODE 90Hz TO 5000Hz 3-WAY WITH ACTIVE FILTERING FOR MIDS AND TWEETERS NOTE: THE CONTROL POSITIO

• ARC Audio IDX, X10 OFF 500Hz X1 = 500Hz X10 OFF 90Hz X 1 = 90Hz X10 OFF 500Hz X 1 = 500Hz IN BAND PASS MODE 90Hz TO 5000Hz 3-WAY WITH ACTIVE FILTERING FOR MID-BASS AND COMPONENT SET NOTE: THE CONTROL POSITIONS SHOWN ARE ONLY ONE SUGGESTED CONFIGURATION. YOUR SYSTEM MAY REQUIRE DEFERENT SETTINGS. 17 IDX Signal to Noise Ratio (A-Weighted) >100dB THD @ 9.0V Output 0.005% Channel Separation >75dB Sub Sonic Filter (12dB/Octave) 15Hz-150Hz Sub Woofer Crossover 50Hz-500Hz 12dB/24dB(MONO) Front High Pass Crossover (12dB/Octave) Rear High Pass Crossover (12dB/Octave) 15Hz-500Hz ( X10=150Hz-5KHz) 15Hz-500Hz ( X10=150Hz-5KHz

Related Products and Documents (Car Stereo System):

Comparable Devices:

Similar Resources:

• JVC KD-S680 (27 pages) ENGLISHINSTRUCTIONSMANUAL DE INSTRUCCIONESMANUEL D’INSTRUCTIONSGET0058-001A[J]ESPAÑOLFRANÇAISFor customer Use:Enter below the Model No. andSerial No. which are located onthe top or bottom of the cabinet.Retain this information for futurereference.Model No.Serial No.For installation and connections, refer to the separate manual.Para la instalación y las …

• Alpine INE-W920R (22 pages) ALPINE INE-W920R/INE-W928R QRG 68-21057Z30-A (EN)ENDEFRESITSENLRUPLGRFOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/PARA USO EN AUTOMÓVILES/SOLO PER L’UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK/ALLEEN VOOR GEBRUIK IN DE AUTO/ТОЛЬКО ДЛЯ ИСПОЛЬЗОВАНИЯ В АВТОМОБИЛЯХ/DO UŻYCIA TYLKO W SAM …

• JVC KD-S70R (4 pages) SERVICE MANUALCD RECEIVERNo.49614Feb. 2001COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD.KD-S70RKD-S70RArea Suffix EEXContinental EuropeCentral EuropeWhen servicing this unit, please refer to the KD-S676R(No.49541) service manual,Which has been issued previously.A part different from KD-S676R was described in this manual.COMPACTDIGITAL AUDIOCon …

• JVC KD-A525J (57 pages) SERVICE MANUALCOPYRIGHT © 2011 Victor Company of Japan, LimitedNo.MA479<Rev.002>2011/2CD RECEIVERMA479<Rev.002>20112SERVICE MANUALKD-A525J, KD-BTP50J, KD-BTP52U,KD-R520J, KD-R521E, KD-R521EU,KD-R521EY, KD-R524UI, KD-R525U,KD-R525UH, KD-R525UN, KD-R526U,KD-R526UH, KD-R526UN, KD-R526UT,KD-R528JCOPYRIGHT © 2011 Victor Company of Japan, LimitedLead …

• Clarion DB225 DB225 DB225 (12 pages) DB225 2English1. When the inside of the car is very cold andthe player is used soon after switching onthe heater, moisture may form on the discor the optical parts of the player and properplayback may not be possible. If moistureforms on the disc, wipe it off with a softcloth. If moisture forms on the optical partsof the player, do not use the player for abo …

• Discount Car Stereo AUX-GM2 (4 pages) Courtesy of:DiscountCarStereo.com Serving the internet community since 1995 AUX-GM2 QUICK START INSTALLATION GUIDE FOR SELECT 1995-05 GM WITH MULTI-DISC CD CHANGER Created November 19, 2015 Revised May 3, 2020 …

Comments, Questions and Opinions: