HP J1530C Installation Instructions Manual
|
HP J1530C, HP J1530C Rack Kit for rp74xx/rx76xx/SEU Servers Installation Instructions Kit contents WARNING: Do not mount this rack integration kit in a rack with sectional columns, such as the HP 5642 rack. If any of the following items are missing or damaged, contact your HP authorized reseller. The following hardware pieces are included in this kit. Quantity Description Picture 1 Cable management arm (5069-6366) 1 Slide, left (A6434-04045) 1 Slide, right (A6434-04046) 3 Cable tie (1400-3011) 2 Mounting bracket and spring (5069-6363) 2 Actuator bracket (5003-0540) 1 Long rod, 17U (5003-0538) 1 Short ro
HP J1530C, Hardware contents Identification Quantity Description Picture A 4 M4 hex lock nut (0535-0076) B 18 M5 x 16-mm screw (0515-3019) C 6 M4 x 6-mm screw (0515-4500) D 18 M5 barrel nut (0590-2318) E 2 10–24 custom nut (A6093-00180) F 2 M4 x 10-mm flat- head screw (0515-4499) J 3 M4 x 8-mm screw (0515-0433) H 18 M5 cage nut (353039-002) Required tools • T-20 Torx driver • T-25 Torx driver • 8-mm hex-nut driver Rack warning WARNING: To reduce the risk of personal injury
HP J1530C, Item Reference Part number 3 Storage bracket A6752-00114 Installing servers into round- hole racks 1. Attach barrel nuts to the front columns. Item Reference 1 Product outline 2 Positions for mounting the product (refer to step 8) 3 Positions for mounting the front of the slides (refer to step 3) 2. Attach barrel nuts to the rear columns. Item Reference 1 Product outline 2 Positions for mounting the cable management arm (refer to step 7) 3 Positions for mounting the rear of the slides (refer to step 3) NOTE: Single racks with a mounted component exceeding 99.79 kg (220.99 lb) do not require a stabilizer k
HP J1530C, Item Reference 1 Stabilizer anti-tip feet 3. Install the right and left slides into the rack. 4. Choose one of the following options: o If you have a lift kit, place the server on the slides, and then go to step 6. o If you do not have a lift kit, then go to step 5. WARNING: The wei g ht of this product requires a lift to install. If a lift is not available, go to step 5 for installation of lift handle panels. If lift handles are already installed, continue
6. Secure the slides to the server. 7. Install the cable management arm. a. Attach screws (B) to the left rear column. b. Slip the cable management arm over the screws (B) and tighten. c. Extend the cable management arm to the left rear side of the product. d. Attach the cable management arm to the studs, and secure it with nuts (E). 8. Install the bezel fro
Item Reference 1 Second product 2 First mounting holes for second product 3 First product 10. Install the rods as shown in the following figure. Installing servers into square- hole racks 1. Attach cage nuts (H) to the front columns. Item Reference 1 Product outline 2 Positions for mounting the product (refer to step 9) 3 Positi
2. Attach cage nuts (H) to the rear columns. Item Reference 1 Product outline 2 Positions for mounting the cable management arm (refer to step 8) 3 Positions for mounting the rear of the slides (refer to step 4) 3. Adjust the slides according to the guidelines in the following table. Item Measurements required for rack 1 465 mm (18.31 in)
HP J1530C, 5. Choose one of the following options: o If you have a lift kit, place the server on the slides, and then go to step 7. o If you do not have a lift kit, then go to step 6. WARNING: The wei g ht of this product requires a lift to install. If a lift is not available, go to step 6 for installation of lift handle panels. If lift handles are already installed, continue to step 7. CAUTION: This server must be unpacked in an ESD safe environment. Observe all ESD safety precautions before attemptin g this procedure. Failure to follow ESD safety precautions can result in damage to the server. 6. Install the lift handles, and place th
HP J1530C, 7. Secure the slides to the server. 8. Install the cable management arm. a. Attach screws (B) to the left rear column. b. Slip the cable management arm over the screws (B) and tighten. c. Extend the cable management arm to the left rear side of the product. d. Attach the cable management arm to the studs, and secure it with nuts (E).
HP J1530C, 9. Install the bezel front. 10. Install the interlock device. NOTE: If the rack is bolted to the floor or is used in a rack configuration with at least four bayed racks, then the interlock device is not necessary. If two products are installed and the rack depth is no more than 717.55 mm (28.25 in), the interlock device can be installed so that you can remove one product at a time. NOTE: The products must be racked adjacent to each other to use the interlock device. NOTE: If four products are installed in the rack and in
HP J1530C, Installing SEU into round-hole racks NOTE: The SEU can only be used with the rp84XX and rx86XX server. Item Reference 1 SEU 2 Server 1. Attach barrel nuts (D) to the front columns. Item Reference 1 SEU outline 2 Positions for mounting the product (refer to step 6) 3 Positions for mounting the front of the slides (refer to step 3) 4 Server
HP J1530C, 2. Attach barrel nuts (D) to the rear columns. Item Reference 1 SEU outline 2 Positions for mounting the cable management arm (refer to step 7) 3 Positions for mounting the rear of the slides (refer to step 3) 4 Server 3. Install the right and left slides into the rack. Do not tighten the outer screws. 4. Remove and discard the center screw, allowing the slide to lower slightly, and then tighten the outer screws. 5. Place the server on the slides using a lift kit. WARNING: The wei g ht of th
HP J1530C, CAUTION: This server must be unpacked in an ESD safe environment. Observe all ESD safety precautions before attemptin g this procedure. Failure to follow ESD safety precautions can result in damage to the server. 6. Insert screws to secure the server to the slides. NOTE: Use the handles only to adjust the position of the server while it is on the slides. Do not use the handles to lift the server. 7. Install the cable management arm. a. Attach screws (B) to the left rear column. b. Slip the cable management arm over the screws (B), and tighten. c. Extend the cable management arm to the left side of the p
HP J1530C, 8. Install the bezel front. 9. Install the interlock device. NOTE: The interlock device is required for each rp84XX and rx86XX and SEU pair installed. NOTE: The products must be racked adjacent to each other to use the interlock device. NOTE: If two pairs are installed, two interlock devices are needed, with one connected to the bottom pair and the other connected to the top pair. Item Reference 1 SEU 2 First mounting holes for SEU 3 Server 10. Install
HP J1530C, 11. Check the clearance between the short rod and the bottom actuator bracket. If the clearance is less than 1 mm (0.04 in), then proceed to step 12. If the clearance is greater than 1 mm (0.04 in), then proceed to step 13. 12. Push the actuator bracket down while tightening the screw. 13. Verify the clearance again. If necessary, readjust, and then go to step 12. Installing SEU into square-hole racks 1. Attach cage nuts (H) to the front columns. Item Reference 1 SEU outline 2 Positions for mounting the product (refer to step 9) 3 Positions for mounting the front of the slides (refer to step 4) 4 Server
HP J1530C, 2. Attach cage nuts (H) to the rear columns. Item Reference 1 SEU outline 2 Positions for mounting the cable management arm (refer to step 8) 3 Positions for mounting the rear of the slides (refer to step 4) 4 Server 3. Adjust the slides. Item Measurements required for rack 1 465 mm (18.31 in) Item Measurements required for rack 2 476.2 mm (18.75 in) 3 711 to 774.7 mm (28 to 30.5 in) 4. Install the right and left slides into the rack. Do not tighten the outer screws. NOTE: Single racks with a mounted component exceeding 99.79 kg (220.99 lb) do not require a stabilize
HP J1530C, 5. Remove and discard the center screw, allowing the slide to lower slightly, and then tighten the outer screws. 6. Place the server on the slides using a lift kit. WARNING: The wei g ht of this product requires a lift to install. Do not manually lift the server to install it. Use a lift that can handle the load of your server. CAUTION: This server must be unpacked in an ESD safe environment. Observe all ESD safety precautions before attemptin g this procedure. Failure to follow ESD safety precautions can result in damage to the server. 7. Insert screws to secure the server to the slides.
HP J1530C, 9. Install the bezel front. 10. Install the long and short rod. Item Reference 1 SEU box 2 First mounting holes for SEU 3 Server 11. Install the rods. 12. Check the clearance between the short rod and the bottom actuator bracket. If the clearance is less than 1 mm (0.04 in), then proceed to step 13. If the clearance is greater than 1 mm (0.04 in), then proceed to step 14.
HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade Racks & Stands Installation manual
P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade |
HP D7171A - NetServer - LPr Racks & Stands Upgrade manual
D7171A - NetServer - LPr |
HP D7171A - NetServer - LPr Racks & Stands Installation manual
D7171A - NetServer - LPr |
HP D7171A - NetServer - LPr Racks & Stands Installation manual
D7171A - NetServer - LPr |
HP LaserJet 1000 series Racks & Stands Operation & user’s manual
LaserJet 1000 series |
HP D7171A - NetServer - LPr Racks & Stands Installation manual
D7171A - NetServer - LPr |
HP D7171A - NetServer - LPr Racks & Stands Datasheet
D7171A - NetServer - LPr |
HP D7171A - NetServer - LPr Racks & Stands Datasheet
D7171A - NetServer - LPr |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Pentax | PV-T20A | Instruction manual | pentax/pv-t20a-613.pdf | 01 Jun 2023 | 24 | 1.27 Mb |
2 | Uniden | scanning radio | Manual | uniden/scanning-radio-7N1.pdf | 25 Jan 2023 | 69 | 1.6 Mb |
3 | Hobo | UX90-005 | Manual | hobo/ux90-005-6M6.pdf | 21 Feb 2023 | 7 | |
4 | Vitek | Alpha Series | Owner's manual | vitek/alpha-series-OFG.pdf | 12 May 2023 | 36 | 2.75 Mb |
5 | Olympus | TCON 300 | Quick start manual | olympus/tcon-300-91W.pdf | 26 Jul 2022 | 2 | |
6 | Philips | GC6315/01 | Operation & user’s manual | philips/gc6315-01-A87.pdf | 18 Apr 2023 | 34 | 0.88 Mb |
NewStar
INSTRUCTION MANUALWWW.NEOMOUNTS.COMFPMA-D700DD4EN NL DE FR IT ES PT DK NO SE FI PL CS SK RO Monitor desk standMonitor bureausteunMonitor TischständerSupport moniteur de bureauSupporto da scrivania per monitorSoporte de escritorio para monitorSuporte de mesa com base para monitorBordstander skærmBordstativ til skjermSkrivbordsstativ för bildskärmNäytön …
Neomounts FPMA-D700DD4(3 pages) |
Clenergy
PV-ezRack SolarMatrix Installation Guide V2.0 NO.:PZ06-IM02-20 Content 1 Product Introduction…………………………………………….. 1 2 Tools & Components ……………………………….. 2 3 System overview…………………………………………. 3 4 Installa …
PV-ezRack SolarMatrix(10 pages) |
Vivo
Instruction ManualEmail: [email protected] chat: www.vivo-us.comCall: 1-800-371-5654 - Scan the QR code with your mobile device or follow the link to helpful videos and specifications related to this product. …
STAND - TV02D(4 pages) |
sauter
Sauter GmbH Tieringerstr. 11-15 D-72336 Balingen E-Mail: [email protected] Tel: +49-[0]7433- 9976-174 Fax: +49-[0]7433-9976-285 Internet: www. sauter.eu Instruction Manual TVP TVP-BA-e-1111 1 Thank you for buying a SAUTER test stand. We hope you are pleased with your high quality test stand with its big functional range. If you have any queries, wish …
TVP(2 pages) |
peerless-AV
ISSUED: 11-01-11 SHEET #: 021-9012-3 01-15-132300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.comMax Load Capacity:5 lbs (2.2 kg)Installation and Assembly:Universal Tablet MountModels: PTM200, PTM200-SFeatures:• Adjustable height and width allows mount to fi t virtually any tablet• Q …
PTM200(8 pages) |
Atdec
Components ChecklistTOOLS REQUIRED:� …
TH-2050-VFM(2 pages) |
Cybernet Monitor i-One Series H5#4T5554 i-One Series H5: Cybernet Monitor Owner Documentation i-One Series H5, 33 |
ESX Car Navigation system VN720 VO-P6CESX VN720 VO-P6C Manual (Doc Type: Car Navigation system Owner's manual) VN720 VO-P6C, 52 |
iHome Headphone LifeTalks IH-H411UPiHome LifeTalks IH-H411UP User Guide (Doc Type: Headphone Knowledge base) LifeTalks IH-H411UP, 4 |
Fischer-Price Baby Carrier X7051Fischer-Price Baby Carrier X7051 Manual X7051, 36 |
Metabo Drill B E 622 S-R+L -#91S3S3: B E 622 S-R+L - Drill Brochure B E 622 S-R+L -, 34 |
Fiamma Toilets Bi-Pot SeriesFiamma Toilets Installation and use instructions manual (File: fiamma-bi-pot-series-installation-and-use-instructions-manual-16, Mon 01.2024) Bi-Pot Series, 16 |
Epson Laptop HX-20Epson HX-20 Laptop Specification sheet HX-20, 2 |
Fetch TV Set-top boxes Gen 1#8J12O3 Gen 1: Fetch TV Set-top boxes Owner Documentation Gen 1, 32 |
Cooler Master Computer Accessories SGC-2100(scout-2)Computer Accessories #81F361 SGC-2100(scout-2), 16 |
SMC Networks Switch SMCGS1610SMC Networks Product Manual: SMCGS1610 PDF Operation & user’s manual - X5S834 SMCGS1610, 32 |
Panasonic Speakers TY-SP42P5KPDF Manual (@N23NPD), Panasonic TY-SP42P5K Speakers (Wednesday 04-10-2023) TY-SP42P5K, 24 |
ZÖLLNER Control Systems Signal Automaton 10+SGA#7MI4E7 Signal Automaton 10+SGA: ZÖLLNER Control Systems Owner Documentation Signal Automaton 10+SGA, 15 |