Manualios.com

Asus 5U Tower Chassis Kit AK35 Operation & User’s Manual

  • 5U Tower Chassis Kit AK35 Enclosure
  • ma2fhaXkkgUks
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 46

Asus 5U Tower Chassis Kit AK35 Manual Online:

3.5, 1525 votes
Asus 5U Tower Chassis Kit AK35 User Manual
Asus 5U Tower Chassis Kit AK35 User Guide
Asus 5U Tower Chassis Kit AK35 Online Manual

Text of Asus 5U Tower Chassis Kit AK35 User Guide:

  • Asus 5U Tower Chassis Kit AK35, ASUS AK35 chassis kit 2-3 2.2 Removing and installing the side cover 2.2.1 Removing the cover 1. Loosen the two thumb screws that secure the side cover. 2. Slide the side cover for about half an inch toward the rear until it is disengaged from the chassis. 2.2.2 Installing the cover 1. Match and insert the hooks of the cover to the elongated holes on the side of the chassis. All the six hooks (three each on the top and bottom) of the cover must properly fit the designated holes. 2. Slide the cover toward the front until it snaps in place. 3. Tighten the thumb

  • Asus 5U Tower Chassis Kit AK35, ii Disclaimer/Copyrights Product Name: ASUS AK35 Manual Edition: Revised edition V2 (E1235) Release Date: May 2003 Copyright © 2003 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). ASUS provides this manual “as is” without warranty of any kind, either express or implied,

  • Chapter 2: Hardware setup 2-20 2.7 Removable components When installing or removing system devices, you may need to remove previously installed components. This section describes how to remove these components. 2.7.1 HDD blower To remove the HDD blower: 1. Disconnect the 3-pin HDD blower cable from the FAN 1 connector on the SCSI backplane. 2. Press the tab at the bottom of the blower

  • iv Contents 2.6 Installing or removing an expansion card ......................... 2-16 2.6.1 Installing a standard size expansion card ............ 2-16 2.6.2 Installing a long expansion card .......................... 2-18 2.6.3 Removing an expansion card .............................. 2-19 2.7 Removable components...................................................

  • Asus 5U Tower Chassis Kit AK35, ASUS AK35 chassis kit 1-3 1.2 Overview The AK35 chassis kit is designed for easy configuration, flexibility, and high reliability. The chassis may be set up as standalone or rack-mount. Flexible expansion Inside the stylish front bezel secured by a lock, the front panel features easily accessible drives bays: • a floppy drive bay (floppy drive already installed) • three 5.25-inch bays (one occupied by a CD-ROM drive) • six 3.5-inch hard disk drive bays with externally removable trays On the rear panel are slots for sev

  • Asus 5U Tower Chassis Kit AK35, Chapter 2: Hardware setup 2-26 The following picture shows the SCSI backplane installed in the system and the cables connected to it. To ensure power redundancy, it is recommended that you use power plugs from each of the redundant power supply modules. Fan cables Power plugs from the power supply SCSI cable LED cables

  • Chapter 2: Hardware setup 2-16 2.6 Installing or removing an expansion card The chassis is designed with a screwless expansion slot frame on the rear panel. This design feature allows you to install or remove an expansion card in less steps. 2. Slide out the metal bracket opposite the PCI slot where you wish to install the expansion card. You may use a flat-

  • Asus 5U Tower Chassis Kit AK35, iii Contents Disclaimer/Copyrights ..................................................................... ii Contents ......................................................................................... iii Notices ............................................................................................v Safety information .......................................................................... vi About this guide............................................................................. vii ASUS Contact Information .......................................

  • Asus 5U Tower Chassis Kit AK35, Chapter 2: Hardware setup 2-22 2.7.3 Roller wheels The chassis comes with four roller wheels for convenient transport. Each wheel has a brake lock to stabilize the chassis in place. To remove the chassis wheels: 1. Lay the chassis in its side. 2. Use a Phillips screwdriver to remove the screws that secure the wheels to the bottom of the chassis. Brake lock Remove the chassis roller wheels if you wish to mount the system to a rack. Refer to the Rackmount Kit manual for more information.

  • Asus 5U Tower Chassis Kit AK35, Chapter 1: Product introduction 1-4 1.3 Front panel features The AK35 chassis kit displays a stylish front bezel with lock. The bezel covers the system components on the front panel and serves as security. Open the bezel to access the front panel components. The front panel is designed to allow convenient access to the hard disk drives and other external features. The power and reset buttons, LED indicators, CD-ROM drive, floppy drive, and two USB ports are also located on the front panel. For future installation of

  • ASUS AK35 chassis kit 2-13 The edge of the tray protrudes about 0.5 cm until you push back the tray lever. 5. Insert the tray with the installed HDD back into the bay. 6. Carefully push the tray all the way to the depth of the bay. 7. Push the tray lever until it clicks in place. The drive tray is correctly placed when its front edge aligns with the bay edge. Make

  • Asus 5U Tower Chassis Kit AK35, Chapter 2: Hardware setup 2-2 2.1 Preparation Before proceeding, prepare everything that you might need to facilitate installation. 2.1.1 Tools to use 1. Phillips head screw driver 2. Flat head screw driver 2.1.2 System components and devices to install The following items are the basics that you need to install into the chassis kit. You may need to install other devices depending on your configuration. 1. Motherboard 2. Hard disk drives 3. Drive cables 4. PCI add-on cards

  • Asus 5U Tower Chassis Kit AK35, viii ASUS Contact Information ASUSTeK COMPUTER INC. (Asia-Pacific) Address: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 General Tel: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: [email protected] Technical Support MB/Others (Tel): +886-2-2890-7121 (English) Notebook (Tel): +886-2-2890-7122 (English) Desktop/Server (Tel): +886-2-2890-7123 (English) Support Fax: +886-2-2890-7698 Web Site: www.asus.com.tw ASUS COMPUTER INTERNATIONAL (America) Address: 44370 Nobel Drive, Fremont, CA 94

  • ASUS AK35 chassis kit 1-7 1.6 LED information The following table describes the LED indicators on the server front and rear panels. LED Status Description Drive Status LED Green Installed HDD is in good condition; supplied power is sufficient Red HDD fails Blinking red HDD is rebuilding using the RAID card SCSI Access Fault-Tolerant Enclosure (SAFTE) Drive Activity LED Blin

  • Asus 5U Tower Chassis Kit AK35, Chapter 2: Hardware setup 2-8 2.4.2 Installing a 5.25-inch drive To install a 5.25-inch drive: 1. Remove the metal cover of the bay where you wish to install the drive by pulling the cover outward. 2. Pull and swing the left edge of the front panel outward. 3. Unhook the hinge-like tabs from the holes on the right side of the front panel to completely detach the front panel assembly from the chassis. 1 Hinge-like tab 2 3

  • Asus 5U Tower Chassis Kit AK35, ASUS AK35 chassis kit 2-17 4. Press the end of the card lock marked “LOCK” to secure the card on the slot. A light click indicates that the card is locked in place. 3. Install the expansion card making sure that it is properly seated on the slot. LOCK Refer to the card documentation for the card configuration details, and to the motherboard user guide in case you need to configure any jumpers after installing the expansion card. 3 4

  • Asus 5U Tower Chassis Kit AK35, Chapter 2: Hardware setup 2-4 2.3 Motherboard installation 2.3.1 Motherboard dimensions This chassis kit supports an ASUS motherboard that measures 12x13 inches (30.5 x 33 cm) for SCSI models, or 12x12 inches (30.5 x 30.5 cm) for IDE models. Motherboards of smaller sizes will fit into the system chassis. Refer to the motherboard user guide for more information on the system requirements. 13 in (33 cm) 12 in (30.5 cm) Make sure that the motherboard you intend to install into the chassis does not exceed the maximum specified dimensions. Otherwi

  • Asus 5U Tower Chassis Kit AK35, ASUS AK35 chassis kit 2-15 4. Prepare hard disk drive. Carefully connect the SCSI-IDE HDD bridge board to the 40-1 pin IDE connector and 4-pin power connector. Make sure that the SCSI-IDE HDD bridge is properly connected. 5. Carefully place the hard disk drive into the drive tray. Align the four (4) screw holes on the drive with those on the tray rails. Secure drive with four round head screws. 6. Secure the SCSI-IDE HDD Bridge to the tray with two (2) round head screws. 7. Re-attach the rear bracket and secure it with two (2) flat head screws. Do not overtighten the screws to avoid breaking the plastic tray rails. SCSI-IDE HDD bridge board 4 5 6 7

  • vi Safety information Electrical Safety Operation Safety IMPORTANT • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing any additional devices to or from

  • Asus 5U Tower Chassis Kit AK35, vii About this guide Contents This guide contains the following parts: 1. Chapter 1: System overview This chapter describes the general features of the AK35 barebone server. It includes sections on front panel and rear panel specifications. 2. Chapter 2: Hardware setup This chapter lists the hardware setup procedures that you have to perform when installing system components. 3. Appendix: Troubleshooting This appendix lists the common problems that you may encounter while using the AK35 barebone s

  • Asus 5U Tower Chassis Kit AK35, Chapter 2: Hardware setup 2-14 2.5.2 IDE hard disk To install an IDE hard disk drive: 1. Place the hard disk tray on a flat clean surface. 2. Use a Phillips screwdriver to remove the screw that secures the middle bracket from the drive tray. 3. Remove that screw that secures the rear bracket to detach it from the drive tray. Rear bracket Middle bracket Drive tray rail Be careful when handling the drive tray rails to avoid breaking them. 1 2 3

  • Asus 5U Tower Chassis Kit AK35, ASUS AK35 chassis kit 2-11 7. Re-install the front panel assembly (front bezel and front panel cover). a. Insert the four hinge-like tabs to the holes on the right edge of the chassis. b. Swing the front panel to the left and fit the four (4) hooked tabs to the left side of the chassis until the tabs snap in place. Hinge-like tab 7b 7a

  • Asus 5U Tower Chassis Kit AK35, Chapter 2: Hardware setup 2-24 2.8 Connecting the cables Refer to the motheboard user guide for detailed information on the connectors. 2.8.1 Motherboard connections The chassis includes power and signal cables that you need to connect to the motherboard, SCSI backplane, and to the devices that you will install. 1. Chassis fan 2. 12V AUX power 3. 24-pin ATX power 4. Primary IDE 5. Secondary IDE 6. SCSI backplane 7. SMBus panel to backplane 8. Floppy disk drive 9. System front panel 10. External SCSI 11. HDD access 12. Front USB Standard cables connected to the motherboard 1 2 3 4 5 6 7 8 9 10 12 11 Most of the cables for the chassis ki

  • Asus 5U Tower Chassis Kit AK35, ASUS AK35 chassis kit 2-19 2.6.3 Removing an expansion card To remove an expansion card: 1. Release the card lock. a. Press the card lock lever. b. The card lock flips up. Card lock Card lock lever 1a 1b 2. Pull out the card from the PCI slot. 3. Press the end of the card lock marked “LOCK” to return it in place. 2

  • Asus 5U Tower Chassis Kit AK35, Chapter 1: Product introduction 1-6 1.5 Internal features The chassis kit includes the basic components as shown in the picture below. System with standard power supply module The power supply area differs depending on the power supply module that came with the server you purchased. System with redundant power supply modules The picture below shows a system redundant power supply modules. All other basic system components are the same as the above picture. 1. Power supply module 2. 5.25-inch drive cage 3. SCSI backplane board

  • Asus 5U Tower Chassis Kit AK35, Chapter 1: Product introduction 1-2 1.1 Package contents 1.1.2 Standard items 1. Chassis kit including: • power supply unit(s) • SCSI backplane board • CD-ROM drive • floppy disk drive • hot-swap HDD trays (6 units) • SCSI-IDE HDD bridge board (6 units) • chassis fan • chassis roller wheels 2. Cables • 6-pin SMBus cable • BP-LED cable • internal SCSI cable • external SCSI cable • chassis intrusion cable • power cable 3. Component screws 4. ASUS AK35 Chassis Kit User Guide 1.1.3 Optional item • ASUS AK35 5U Rackmount Rail Ki

  • Asus 5U Tower Chassis Kit AK35, ASUS AK35 chassis kit 2-7 2.4 Installing 5.25-inch drives Three 5.25-inch drive bays are located on the upper front part of the chassis. A CD-ROM drive that comes standard with the system package occupies the uppermost bay (labeled 1) . The two lower bays (labeled 2 and 3) are available for additional 5.25-inch devices. Before you can install a 5.25-inch drive, you should first remove the front panel assembly (front bezel and front panel cover). The front panel assembly is attached to the chassis through four hooked tabs on the left side and four hinge-like tabs on the right side. To remove the front panel assembly: 1. Use a flat-head screwdriver to detach the hooked tabs from the le

Related Products and Documents (Enclosure):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Canon imageRUNNER C4080 SERIES Specifications canon/imagerunner-c4080-series-RAT.pdf 18 Mar 2023 12 5.17 Mb
2 Luxinup 32 User and maintenance manual luxinup/32-832.pdf 18 Apr 2023 7
3 Metcal DX-355 Operation & user’s manual metcal/dx-355-N1C.pdf 08 Nov 2023 5
4 Linksys WAP54GPE - Wireless-G Exterior Access Point Operation & user’s manual linksys/wap54gpe-wireless-g-exterior-access-point-T64.pdf 01 Sep 2022 76
5 Next YE-GD101 Operation & user’s manual next/ye-gd101-LZ3.pdf 10 Dec 2023 20
6 Spectra Logic Spectra 12000 Operation & user’s manual spectra-logic/spectra-12000-ZOV.pdf 25 Jan 2023 190 2.5 Mb

Similar Resources:

  • hager

    TN003S

    (2 pages)
    TN003SMontage / Installation / Montage / Montagem16T 6192B6T 6192B~ 60 mmT568A8721T568A3456876 5 4 3218721T568B3456T568BCâble Cat 6 UTP /Cable Category 6 UTPKabel av kategori 6 UTP /Cabo Cat 6 UTPDénuder les câblesStrip the cableSkala kabelnDescarnar os cabosLe TN003S est composé d'un connecteur RJ45 et d'un support modulaireclipsable dans un c …
  • Conrad

    SATA

    (4 pages)
    2.5“-SATA-Festplattengehäuse Version 11/08USB2.0 °Best.-Nr. 41 26 15Bestimmungsgemäße VerwendungIn das Gehäuse kann eine 2.5“-SATA-Festplatte eingebaut werden. Der Betrieb ist über eineUSB2.0-/USB1.1-Schnittstelle möglich. Die Stromversorgung erfolgt per USB.Dieses Produkt erfüllt die gesetzlichen, nationalen und europäischen Anforderungen. Alle …
  • Martin Audio

    WWTT22

    (1 pages)
    WWTT22Arrayable two-way compact theatre enclosurefeatures Arrayable compact trapezoid enclosure High SPL output capability 70º coverage angle Multi-laminate birch plywood construction Switchable active/passive operation Certified MAN quick-connect flying optionapplications Theatre sound systems Club sound reinforcement Music playb …
  • Corsair

    Carbide series

    (38 pages)
    CARBIDE SERIES®INSTALLATION GUIDE n GUIDE D’INSTALLATIONINSTALLATIONSANLEITUNG n Guía de instalación РУКОВОДСТВО ПО УСТАНОВКЕ n GUIA DE INSTALAÇÃOインストールガイド 47100 Bayside Parkway • Fremont • California • 94538 • USA | corsair.com© 2015 Corsair Components, Inc.All rights reserved. Corsair, the sails logo …
  • OEZ

    QA40 Series

    (27 pages)
    OEZ s.r.o., Šedivská 339, 561 51 Letohrad, Czech Republic, www.oez.cz 991172b Z00ENGLISHČESKYINSTRUCTIONS FOR USE, NÁVOD K POUŽITÍ SIDE-BY-SIDE SWITCHBOARD CABINET ŘADOVÁ ROZVÁDĚČOVÁ SKŘÍŇQA40……QA55……QA40……QA55……Mounting tools:Nářadí pro montáž:- Inbus 5; 6- spanner: 10; 13klíč- screwdriver: PZ2 šroubovákInsta …
  • Vantec

    External Hard Drive Enclosure NexStar CX

    (1 pages)
    2.System Requlrements54-2 Insert the hard drive caddy back into the NexStar CX housing as the picture below. Be sure to align the caddy with the guides within the housing.Owner’s ManualCopyright © 2007 Vantec Thermal Technologies. All Rights Reserved.All Registered Trademarks Belong To Their Respected Companies.Model:NST-200S2-BKwww.vantecusa.com …

Comments, Questions and Opinions: