Asus PRL-DLS533 Operation & User’s Manual

Text of Asus PRL-DLS533 User Guide:

• 4-18 Chapter 4: BIOS Setup 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes. Configuration options: [R/W] [Read Only] Onboard Serial Po

• Asus PRL-DLS533, 5-48 Chapter 5: Driver installation NT4 W2K WXP NNW SCO UNX LNX C5. Rebuilding the Kernel 1. To rebuild the kernel, type: /etc/conf/cf.d/link_unix 2. The system displays will prompt for responses to these messages: a. Do you want this kernel to boot by default (y/n)? Type: y Press Enter. The system backs up the old kernel. b. Do you want the kernel environment rebuilt (y/n)? Type: y Press Enter. 3. To activate the new kernel, you must reboot the system. Type the command: reboot Press Enter. 4. After the system reboots and the "boot:" prompt appears, press Enter to load the new kernel. 5. Log in as usual.

• vii Safety information Electrical safety • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing sys

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 2-5 Follow these steps to install a CPU. 1. Locate the 604-pin ZIF sockets on the motherboard. Unlock the socket by pressing the lever sideways, then lift it up to at least 115° angle. 2. Position the CPU above the socket as shown. 3. Carefully insert the CPU into the socket until it fits in place. Make sure that the socket lever is lifted up to at least 115° angle, otherwise the CPU does not fit in completely. The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent b

• Asus PRL-DLS533, 4-16 Chapter 4: BIOS Setup OS/2 Onboard Memory > 64M [Disabled] When using OS/2 operating systems with installed DRAM of greater than 64MB, you need to set this option to [Enabled]. Otherwise, leave to the default setting [Disabled]. Configuration options: [Disabled] [Enabled] USB Legacy Support [Auto] This motherboard supports Universal Serial Bus (USB) devices. The default of [Auto] allows the system to detect a USB device at startup. If detected, the USB controller legacy mode is enabled. If not d

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 4-9 Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. To set a password, highlight the appropriate field and press <Enter>. Type in a password then press <Enter>. You can type up to eight alphanumeric characters. Symbols and other characters are ignored. To confirm the password, type the password again and press <Enter>. The password is now set to [Enabled]. This password allows full access to the BIOS Setup menus. To clear the password,

• Asus PRL-DLS533, 5-54 Chapter 5: Driver installation NT4 W2K WXP NNW SCO UNX LNX 5.7.3 ATI ® Rage XL Display Driver Installation SCO UnixWare 7.1.1 system can correctly recognize ATI Rage XL graphic controller (ATI MACH64) during installation. User doesn’t need to load or modify the video driver for the onboard VGA device. 6. If you are downloading the latest driver from the Intel website,save the package to a directory on your system; for example, the /tmp directory. You can install the driver from this directory or spool the driver from the directory so the driver resides on the system. Example of installing the driver from the directory: pkgadd –d

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 4-17 4.4.1 Chip Configuration Video Memory Cache Mode [UC] USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor. It can greatly improve the display speed by caching the display data. You must set this to UC (uncacheable) if your display card cannot support this feature; otherwise your system may not boot. Configuration options: [UC] [USWC] Onboard PCI IDE [All] You can select to enable the primary, secondary, tertiary IDE channel, all channels, or disable all channels. Configuration options: [All] [Primary\Secondary] [Primary\Tertiary] [Primary] [Secondary\Tertiary\ [Secondary] [T

• 4-34 Chapter 4: BIOS Setup Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Yes] to load default values. Select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM. D

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 4-5 4.2 BIOS Setup program This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future. For example, you may want to enable the security password feature or make changes to the power management settings.

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard Chapter summary 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program...................................... 4-5 4.3 Main Menu ...................................................... 4-8 4.4 Advanced Menu ........................................... 4-15 4.5 Power Menu .................................................. 4-22 4.6 Boot Menu .................................................... 4-27 4.7 Server Menu ......................................

• Asus PRL-DLS533, 4-12 Chapter 4: BIOS Setup Translation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity. Configuration options: [LBA] [LARGE] [Normal] [Match Partition Table] [Manual] Cylinders This field configures the number of cylinders. Refer to the drive documentation to determine the correct value. To make changes to this field, set the Type field to [User Type HDD] and the Translation Method field to

• ASUS PRL-DLS533 motherboard user guide 2-21 4. Chassis alarm lead (4-1 pin J3) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this lead to record a cha

• Asus PRL-DLS533, 5-36 Chapter 5: Driver installation NT4 W2K WXP NNW SCO UNX LNX 5.5.2 Broadcom Gigabit LAN Driver Installation Installing the Driver Software Installing Novell NetWare Server 5.x/6.0 Please ensure that the server has the latest support pack available installed. The latest support packs can be found at: http:// support.novell.com/misc/patlst.htm. You may want to create an archive disk by copying all the files from the CDROM\Netware\Driver directory onto a floppy disk. If you choose to use the CDROM directly, ensure that the CDROM.NLM is l

• Asus PRL-DLS533, 4-4 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary. This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears. 8. Follow the onscreen instructions to continue. If you encounter problems while updating the new BIOS, DO NOT turn off the system because this may cause boot problems. Just repeat the process, and if the problem persists, load the original BIOS file you saved to the boot disk. If the Flash Memory Writer

• Asus PRL-DLS533, 5-14 Chapter 5: Driver installation NT4 W2K WXP NNW SCO UNX LNX 5.3 Microsoft ® Windows ® 2000 Server 5.3.1 LSI ® SCSI Driver Installation Windows 2000 Server does not have drivers for the new SCSI controllers, you must load the driver manually prior to Windows 2000 Server installation. A. Preparing an LSI Driver Disk From the support CD, locate the LSI drivers in the following path: \Drivers\SCSI\FUSION-MPT\Windows\1.08.22\Win2000 This procedure installs the SYMMPI.SYS driver onto a new or existing Windows 2000 Server system. Depending upon the media used to d

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 4-1 4.1.1 Creating a bootable disk AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode. To determine the BIOS version of your motherboard, check the last four numbers of the code displayed on the upper left-hand corner of your screen during bootup. Larger numbers represent a newer BIOS file. 1. Type FORMAT A:/S at the DOS prompt to create a bootable system disk. DO NOT copy AUTOEXEC.BAT and CONFIG.SYS to the disk. 2. Type COPY D:\AFLASH\AFLASH.EXE A:\ (assuming D is your CD-ROM drive) to copy AFLASH.EXE to the boo

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 5-5 NT4 W2K WXP NNW SCO UNX LNX B2. Boot Floppy Disk Installation 1. Have the driver diskette available for inserting into the A: drive when prompted. Depending upon the media used to distribute drivers (web or CDROM), you will create a driver diskette. IMPORTANT: Read Step 2 before performing the instructions contained within this step. 2. Start the Windows NT 4.0 installation by booting from the Microsoft Setup floppy diskette. 3. Press Enter when the Welcome to Setup screen appears. The Windows NT 4.0 Workstation Setup window appears next. 4. Press S to skip automatic de

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 4-25 Power On By PS/2 Keyboard [Disabled] This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Automatic Power Up [Disabled] This allows an unattended or automatic system power up. You may configure your system to power up at a certain time of the day by selecting [Everyday] or at a certain time and day by selecting [By Date]. Configuration options: [Disabled] [Everyday] [By Date]

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 2-9 The system chipset only supports PC2100/1600 registered ECC DIMMs. Make sure to use only the specified DIMM types for stable system operation. 2.5.2 Memory Configurations The motherboard supports system memory of up to 4GB in a one-way non-interleaved configuration. Memory configuration table DIMM Socket 184-pin ECC DDR DIMM Total Memory DDR1 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) = DDR2 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) = DDR1 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) = DDR2 SDRAM 128MB, 256MB, 512MB, 1GB, 2GB (x1) = Total System Memory (Max. 4GB) =

• Asus PRL-DLS533, viii About this guide This user guide contains the information you need when installing this ASUS motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of this motherboard. It includes brief descriptions of the special attributes of the motherboard and the new technology it supports. • Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. I

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 2-29 2. Disabled CPU cache. 3. Check if go to BOOTBLOCK POST. POST Code < 05h > 1. Blank out the video screen. 2. Initialized the keyboard. POST Code < 07h > 1. Used walking 1's algorithm to check out interface to CMOS circuitry. 2. Also set real-time clock power status. Then check for override. POST Code < 09h > 1. Programed chipset register to default value according to ROMTABLE. 2. early initialize CPU. 3. Initialized APIC. 4. Set A20 off. POST Code < 0Ah > 1.

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 2-31 POST Code < 3Dh > 1. Initialize and install mouse and 40: area stuff... 2. Set extended memory size. 3. Save EXT_MEM_Size_MB in G_RAM. 4. Expanded ACPI table into memory. 5. Setup ACPITable and ACPINVS Size. 6. According to length of ACPI table to decrease Ext_MEM_FOUND, EXT_MEMORY. 7. After extended memory test, copy all ACPI tables to ACPI reclaim area (just below top of extended memory, see ATBASE INT15 function 0e820h). Then fill in physical address and checksum for all ACPI tables. 8. Get extended memory size and set size for

• Asus PRL-DLS533, 2-14 Chapter 2: Hardware information 2.7 Switches and jumpers 2.7.1 Switches The following figure shows the location and default settings of the DIP switches on the motherboard. PRL-DLS533 ® PRL-DLS533 DIP Switches SW2 1. Reserved 2. Reserved 3. Reserved 4. Reserved 5. Frequency Multiple 6. Frequency Multiple 7. Frequency Multiple 8. Frequency Multiple ON 12345678 OFF ON Keep the default settings for stable system operation. PRL-DLS533 ® PRL-DLS533 CPU External Frequency Selection (Defaul t) 533MH z 400MHz 3 2 1 2 ON 12345 ON 12345 SW1

• Asus PRL-DLS533, ASUS PRL-DLS533 motherboard user guide 4-31 Remote Console [Disabled] This field allows the text mode VGA display to be sent out to VT100 terminal through COM1. This function is effective at BIOS POST and DOS environment. Configuration options: [Disabled] [Enabled] [POST Only] Event Log Viewer Pressing <Enter> on this item gives you a sub-menu. You will be shown all events such as “no bootable media” or “fan speed out of range”. Clear Event Log [Disabled] This field clears the event log recorded on the sub-menu. Select [Enabled] to autom

• ASUS PRL-DLS533 motherboard user guide 5-21 NT4 W2K WXP NNW SCO UNX LNX 5.3.3 Intel ® Gigabit LAN Driver Installation You may install the Intel 82540EM LAN drivers directly from the support CD. Proceed to the section “B. Update LAN Driver on an Existing System Installation.” If you wish to create a LAN driver disk, proceed to the section “A.Preparing the Intel LAN Driver Dis

• Asus PRL-DLS533, 5-26 Chapter 5: Driver installation NT4 W2K WXP NNW SCO UNX LNX 5.3.5 Enabling ATA100 Feature in Windows ® 2000 To enable the ATA100 feature under Windows 2000, you need to upgrade to Windows 2000 Service Pack 2 or later. 5.3.4 ATI ® Rage XL Display Driver Installation Windows 2000 system can automatically recognize the ATI RAGE XL PCI driver during system installation. You do not need to load any driver for supporting the onboard ATI RAGE XL graphics controller chipset.

• Asus PRL-DLS533, 5-58 Chapter 5: Driver installation NT4 W2K WXP NNW SCO UNX LNX 5. To configure network protocol and address, refer to Linux-specific documentations. NOTE: If compiling the driver under SuSE's 7.x kernel and errors are reported, follow the general guidelines below to rebuild the kernel source tree. Kernal Source Tree Guidelines cd /usr/src/linux-<kernel_version>.SuSE cp /boot/vmlinuz.config .config cp /boot/vmlinuz.version.h include/linux/version.h cp /boot/vmlinuz.autoconf.h include/linux/autoconf.h make oldconfig make dep where <kernel_version> is the actual kernel version

Related Products and Documents (Server):

Comparable Devices:

Similar Resources:

• Compaq BL10e - HP ProLiant - 512 MB RAM (21 pages) Abstract .............................................................................................................................................. 2 Introduction ......................................................................................................................................... 2 Software-layer abstraction: virtual machines ...... …

• Verbatim MediaShare (13 pages) User Manual for Kindle Fire 2 Table of ContentsTABLE OF CONTENTS .............................................. 2!ABOUT THIS MANUAL .............................................. 3!PRODUCT OVERVIEW ............................................... 3!PRODUCT FEATURES ................................................. 3!OPERATING MODES ...................... …

• HP ProLiant DL320e (68 pages) HP Scripting Toolkit for Linux User GuideAbstractThis document provides information about the Scripting Toolkit for Linux utilities and how best to use the Scripting Toolkit forLinux to configure HP ProLiant servers and BladeSystem infrastructure in a Linux environment. This document is intended for ITexperts with experience in scripting operating system ins …

• Alarm.Com ADC-VS121 (2 pages) Video Server (ADC-VS121) INSTALLATION GUIDE Required Items for Installation:  Video Server and power adapter (included)  Broadband (Cable, DSL, or Fiber Optic) Internet connection with router  Personal computer or web-enabled tablet  Login/Password for the customer’s Alarm.com account  Analog CCTV camera with power supply (not …

• Vicon Valerus Shadow Elite (2 pages) Quick Start Guide: Shadow Elite Small Form Factor Application Servers This sheet covers the installation of the Valerus Elite Application Servers small form factor. This system should only be installed by a qualified technician using common hand tools and approved materials in accordance with the National Electrical Code ANSI/NFPA 70, state and local wiring …

• HPE ProLiant MicroServer Gen10 (145 pages) UEFI System Utilities User Guide forHPE ProLiant Gen10 Servers and HPESynergyPart Number: 881334-005Published: June 2018Edition: 1AbstractThis guide details how to access and use the Unified Extensible Firmware Interface (UEFI)that is embedded in the system ROM of all ProLiant Gen10 servers and HPE Synergycompute modules. It details how to access and use bot …

Comments, Questions and Opinions: