Asus RS300-E6 Series Operation & User’s Manual
|
Asus RS300-E6 Series, Chapter 1: Product introduction1-10 1.7.3 HDD status LED RS300-E6/PS4HDDLEDStatusDenition LED Status Description Power Green Light ON Power On OFF HDD Not Found Active Green Blink Data Read/Write to HDD HDD Power LED HDD Active LED RS300-E6/PS2HDDLEDStatusDenition HDD Power LED HDD Active LED LED Status Description Power Green Light ON Power On Red Light ON HDD Fail Green / Red Light Blinking Rebuilding RAID Array OFF HDD Not Found Active Green Blinking Data Read/Write to HDD
Asus RS300-E6 Series, ASUS RS300-E6 Series 7-9 6. Select No and press <Enter> to continue. More Driver Disks? Do you wish to load any more driver disks? Yes No 7. Select your desired language and press <Enter> to continue. OK # Choose a Language What language would you like to use during the installation process? Catalan Chinese(Simplied) Chinese(Traditional) Croatian Czech Danish Dutch English 8. Select your keyboard type and press <Enter> to continue. OK # Ke
Asus RS300-E6 Series, Chapter 2: Hardware setup2-6 2.2.2 Installing the CPU heatsink and airduct To install the CPU heatsink 1. Remove the protection sticker on the back of the CPU heatsink. Protection sticker Tighten the four heatsink screws in a diagonal sequence. A B B A 3. Twist each of the four screws with a Philips (cross) screwdriver just enough to attach the heatsink to the motherboard. When the four screws are attached, tighten them one by one to completely secure the heatsink. 2. Place the heatsink on top of the installed CPU, ensuring that the four fasteners match the holes on the motherboard. 4. Secure the heat pipe and air duct to the server with two screws.
Asus RS300-E6 Series, ASUS RS300-E6 Series 5-7 5.2.2 Menu bar The menu bar on top of the screen has the following main items: Main For changing the basic system conguration Advanced For changing the advanced system settings Server For changing the advanced server settings Power For changing the advanced power management (APM) conguration Boot For changing the system boot conguration Tools For conguring options for special functions Exit For selecting the exit options and loading default settings To select an item on the menu bar, press the
Asus RS300-E6 Series, iv Contents 2.8.3 Installing ASMB4 series management board (optional) 2-20 Chapter 3: Installation options 3.1 Installing friction rail kit items .................................................... 3-2 3.1.1 Attaching the xing latches to the server ........................ 3-2 3.1.2 Attaching the rack rails .................................................... 3-3 3.1.3 Mounting the server to the rack ...................................... 3-4 3.2 Installing optional ball-bearing rail kit items ............................. 3-5 3.2.1 Attaching the rails to the server ...................................... 3-5 3.2.2 Attaching the rack rails ...............
Asus RS300-E6 Series, 2-7ASUS RS300-E6 Series 2.3 System memory 2.3.1 Overview The motherboard comes with six (6) Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) sockets. The gure illustrates the location of the DDR3 DIMM sockets: 2.3.2 MemoryCongurations You may install 1 GB, 2 GB, 4 GB, 8 GB Registerd, or 1 GB, 2 GB, 4 GB Unbuffered with ECC/Non-ECC DDR3 DIMMs into the DIMM sockets using the memory congurations in this section. • Always install DIMMs with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor. DO NOT combine RDIMM and UDIMM. • The motherbo
Asus RS300-E6 Series, 3-5ASUS RS300-E6 Series 3.2 Installing optional ball-bearing rail kit items Your optional ball-bearing rail kit package contains: • two pair of server rails (for the server) • two pairs of rack rails (for the rack) • Nut-and-bolt type screws 3.2.1 Attaching the rails to the server To attach the server rails: 1. Attach the front end of the server rail to the side of the chassis, matching each of the three hooks to the holes on the rail. Then slide the rail toward the front panel until it locks in place. Rack railsFront endRear endNuts and screws 2. Sec
Asus RS300-E6 Series, ASUS RS300-E6 Series 5-13 5.3.6 System Information This menu gives you an overview of the general system specications. The BIOS automatically detects the items in this menu. BIOS Information Displays the auto-detected BIOS information. Processor Displays the auto-detected CPU specication. System Memory Displays the auto-detected system memory. System Memory Information Displays system memory information. BIOS SETUP UTILITY Main BIOS Information BIOS Version :0208 BIOS Build Date :07/21/09 Processor Type :Intel(R) Xeon(R) CPU X3440 @ 2.53GHz Speed :2533
5-24 Chapter 5: BIOS setup ChipsetACPIConguration Energy Lake Feature [Disabled] Allows you to enable or disable the Energy Lake feature. Conguration options: [Enabled] [Disabled] We do not recommend you enable this feature. APIC ACPI SCI IRQ [Disabled] Allows you to enable or disable the APIC ACPI SCI IRQ feature. Conguration options: [Disabled] [Enabled] High Performance Event
Asus RS300-E6 Series, Chapter 2: Hardware setup2-14 2.6 Cable connections • The bundled system cables are pre-connected before shipment. You do not need to disconnect these cables unless you will remove pre-installed components to install additional devices. • Refer to Chapter 4 for detailed information on the connectors. Standard cables connected to the motherboard 1. 24-pin ATX power connector (from power supply to motherboard) 2. 8-pin 12V power connector (from power supply to motherboard) 3. System
Asus RS300-E6 Series, 7-4 Chapter 7: Driver installation To create a RAID driver disk in Windows ® environment 1. Start Windows ® . 2. Place the motherboard support DVD into the optical drive. 3. Go to the Make Disk menu, and then select the type of RAID driver disk you want to create. 4. Insert a oppy disk into the oppy disk drive. 5. Follow succeeding screen instructions to complete the process. Write-protect the oppy disk to avoid computer virus infection. To create a RAID driver disk in Red Hat ® Enterprise Linux server environment 1. Insert a blank formatted high-density oppy disk to the oppy disk drive. 2. Type dd i
Asus RS300-E6 Series, 6-14 Chapter 6: RAID conguration UsingtheObjectscommand To initialize the virtual drives using the Objects command 1. From the Management Menu , select Objects>VirtualDrive , and then press <Enter>. Management Menu Congure Initialize Objects Rebuild Check Consistency Change VD Parameters Objects Adapter Virtual Drive Physical Drive LSI Software RAID Conguration Utility Ver A.62 Apr 29, 2009 BIOS Version A.09.04300936R Use Cursor Keys To Navigate Between Items And Press Enter To Select An Optio
Asus RS300-E6 Series, ASUS RS300-E6 Series 5-5 5.1.3 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS le when it fails or gets corrupted during the updating process. You can update a corrupted BIOS le using a USB ash drive that contains the updated BIOS le. Prepare a USB ash drive containing the updated motherboard BIOS before using this utility. RecoveringtheBIOSfromaUSBashdrive To recover the BIOS from a USB ash drive: 1. Inse
Asus RS300-E6 Series, 6-28 Chapter 6: RAID conguration 6.3.3 Deleting a RAID set Take caution when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set 1. From the utility main menu, select 2. Delete RAID Volume and press <Enter>. The following screen appears. 2. Use the up/down arrow key to select the RAID set you want to delete, and then press <Del>. The following warning message appears. 3. Press <Y> to delete the RAID set and return to the utility main menu, or press <N> to return to the DELETE VOLUME
viii Safety information Electrical Safety • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing any additional devices to or from th
Asus RS300-E6 Series, Chapter 4: Motherboard information4-6 4. LAN controller setting (3-pin LAN_SW1, LAN_SW2) These jumpers allow you to enable or disable the onboard Intel ® Intel 82574LGigabit LAN controllers. Set to pins 1–2 to activate the Gigabit LAN feature. 5. Intel ® 3420 SATA port S/W RAID setting (3-pin RAID_SEL1) This jumper allows you to select the Serial ATA RAID conguration utility to use when you create disk arrays. Place the jumper caps on pins 1–2 if you want to use the LSI Logic Embedded SATA RAID Setup Utility (default); otherwise, place the jumper caps on pins
Asus RS300-E6 Series, Chapter 3: Installation options3-2 3.1 Installing friction rail kit items Your friction rail kit package contains: • Two pairs of rack rails (for the rack) • Nut-and-bolt type screws and one pair of server latches Nuts and screws Front rack rails Rear rack rails 3.1.1 Attachingthexinglatchestotheserver Refer to the image below for the locations to attach the two xing latches to the two sides of the server with four screws. Fixing latch
Asus RS300-E6 Series, ASUS RS300-E6 Series 6-3 6.1.3 RAID controller selection You can choose either the LSI Software RAID Conguration Utility or the Intel Matrix Storage Manager as the default utility to create RAID set(s). See 5. Intel ® 3420 SATA port S/W RAID setting on page 4-6 for details. 6.1.4 Setting the RAID item in BIOS You must enable the RAID function in the BIOS Setup before creating RAID set(s) using SATA HDDs. To do this: 1. Enter the BIOS Setup during POST. 2. Go to the Main menu > IDEConguration , and then press <Enter>. 3. Set the CongureSATA
Asus Z5 Server Operation & user’s manual
Z5 |
Asus ESC2000 G2 Server Configuration manual
ESC2000 G2 |
Asus LSI SAS3442X-R Server Operation & user’s manual
LSI SAS3442X-R |
Asus RS260-E3 RS8 Server Service manual
RS260-E3 RS8 |
Asus ESC4000 Server Operation & user’s manual
ESC4000 |
Asus AP130-D5 Server Operation & user’s manual
AP130-D5 |
Asus AP200 Server Hardware reference manual
AP200 |
Asus Pentium 4 1U Rackmount Server AP160R-S Server Operation & user’s manual
Pentium 4 1U Rackmount Server AP160R-S |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Murray | 405000x8B | Instruction book | murray/405000x8b-N47.pdf | 12 Dec 2022 | 52 | |
2 | Samsung | UN32D6000 | Operation & user’s manual | samsung/un32d6000-O3H.pdf | 13 Feb 2024 | 50 | 14.15 Mb |
3 | Samsung | SIR-T150 | Instructions manual | samsung/sir-t150-516.pdf | 12 Dec 2022 | 38 | 1.4 Mb |
4 | Creative | Video Blaster WebCam Go | Operation & user’s manual | creative/video-blaster-webcam-go-76Q.pdf | 12 Jan 2024 | 47 | 9.46 Mb |
5 | Husqvarna | GTT348 | Owner's manual | husqvarna/gtt348-1T7.pdf | 08 Feb 2024 | 11 | |
6 | Haier | HRF-305 | Owner's manual | haier/hrf-305-96C.pdf | 10 Oct 2022 | 23 | 1.82 Mb |
Wiwynn
Wiwynn™ SV7220-2 Maintenance User Manual Version 1.1 Published Sept. 2014 Copyright © 2014 Wiwynn. All rights reserved
…
SV7220-2(45 pages) |
IS5 COMMUNICATIONS
Intelligent 6 Port Device Server iDS6 Series User’s Manual Version 1.2 Mar 2017 iS5 Communications Inc. #3-7490 Pacific Circle, Mississauga, Ontario Tel: 905-670-0004 Fax: 289-401-5206 Website: www.iS5Com.com E-mail: [email protected]
…
iDS6 Series(37 pages) |
HP
rp5400, rp5430, rp5450 and rp5470 Troubleshooting and Build-Up Procedures Product UpdateManufacturing Part Number: rp54xx_UpdateJuly 2003U.S.A.© Copyright 2003, Hewlett-Packard Development Company, L.P.
…
L1000 - 9000 - 0 MB RAM(8 pages) |
VERITAS
Replacing a power supply: Veritas ApplianceDocument Number: 177Version: 4.3 (05/04/2020)PurposeThis document describes the process for replacing a power supply in a Veritas appliance.Affected appliance models• 3340 Appliance• 5240 Appliance• 5250 Appliance• 5340/5340 HA ApplianceElectrical SafetyThe static discharged by human bodies can damage static …
Access 3340(5 pages) |
TANDBERG
D14111.02—MAY 2008 1www.tandberg.comTANDBERG Content ServerUser GuideThank you for choosing TANDBERG! The TANDBERG Content Server provides you with a quick and easy way to record video meetings and view them live or on demand from your computer.This user guide has been divided into several chapters that you can access.by clicking on the chapter titles in …
Content Server None(14 pages) |
TRENDnet
Wireless G Multi-Function USB Print Server (TEW-MP1U) is designed to transform virtually any stand-alone multi-function USB printer into a shared resource on your wireless network. An intuitive utility and a user-friendly configuration interface provide a seamless user experience. LED indicators and bidirectional support allow for easy print server managemen …
TEW-MP1U(2 pages) |
Panasonic Cassette Player RQ-SX47Panasonic Cassette Player Operating instructions (File: panasonic-rq-sx47-operating-instructions-2, 04/09/2023) RQ-SX47, 2 |
Varimixer Mixer W80W80 (Mixer ePDF User Manual, #G35U79) W80, 42 |
Advanced Greig Laminators, Inc. Laminator AGL64i#77S1VR AGL64i: Advanced Greig Laminators, Inc. Laminator Owner Documentation AGL64i, 65 |
Samsung Cell Phone SGH Z130Samsung Cell Phone SGH Z130 Service manual SGH Z130, 47 |
Sylvania Portable DVD Player SDVD7015Sylvania Product Manual: SDVD7015 PDF Product features - 6OL7U6 SDVD7015, 1 |
Evolution Wheelchair Models S-250-16Evolution Wheelchair Models S-250-16 Operation & user’s manual Models S-250-16, 16 |
ACRONIS Other SNAP DEPLOY -ACRONIS SNAP DEPLOY - User Manual (Manual ), @159PLD SNAP DEPLOY -, 57 |
Vivanco Other 3WAY RF POWER SOCKET SET3WAY RF POWER SOCKET SET (Other ePDF Manual, #BU949H) 3WAY RF POWER SOCKET SET, 20 |
Pfeiffer Vacuum Transmitter TPR-270TPR-270 (Transmitter ePDF User Guide, #C1XM7F) TPR-270, 19 |
Lexus Automobile GS 450h 2006GS 450h 2006 (Automobile ePDF User Manual, #P9CW4B) GS 450h 2006, 15 |
Maytag Oven MMW7530WDWMaytag MMW7530WDW Oven Product dimensions MMW7530WDW, 1 |
USSC Gas Heater VF30ILUSSC VF30IL Manual (Doc Type: Gas Heater Operation & user’s manual) VF30IL, 28 |