Cisco PA-4C-E 1 Installation And Configuration Manual

Text of Cisco PA-4C-E 1 User Guide:

• 14 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Table 4 lists the specific Cisco IOS software images that are compatible with the HP ESCON PA. Table 5 specifies the recommended minimum level of HP ESCON PA microcode for the corresponding Cisco IOS release. For the latest Cisco IOS release that supports the HP ESC

• Cisco PA-4C-E 1, 15 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Safety Guidelines This section provides safety guidelines that you should follow when working with any equipment that connects to electrical power or telephone wiring. Safety Warnings Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might harm you. A warning symbol precedes each warning statement. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could

• Cisco PA-4C-E 1, 21 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Removing and Installing Port Adapters This section describes how to remove port adapters from supported platforms and also how to install new or replacement port adapters.This section contains the following subsections: • Handling Port Adapters, page 21 • Online Insertion and Removal, page 22 • Port Adapter Removal and Installation, page 23 • Attaching the HP ESCON PA to the Channel, page 25 Handling Port Adapters Each port adapter circuit board is mounted to a metal carrier and is sensitive to electrostatic disc

• 11 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview Table 3 describes the interface addresses for the Cisco 7200 series routers, includingCisco 7200 VXR routers. Cisco 7200 Series Routers and Cisco 7200 VXR Routers Interface Addresses In Cisco 7200 series routers, port adapter slot numbers port adapter slots are numbere

• Cisco PA-4C-E 1, 39 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Expanding disk0:xcpa27-1_seg_push (15488 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_tcpip (161140 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_tn3270 (620400 bytes):!!!!!!!!!!! [OK - 2739200/5478400 bytes] 2739200 bytes copied in 68.500 secs (40282 bytes/sec) To update your running configuration: Step 1 Enter the following commands, beginning in global configuration mode: Router# configuration term Router(config)# microcode ecpa diskX : xcpaXX-YY Router(config)# microcode reload Router(confi

• Cisco PA-4C-E 1, 13 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation The following example is a partial display of the show microcode command output: Router# show microcode Microcode images for downloadable hardware HW Type Microcode image names ------------------------------------------ ecpa default slot0:xcpa28-0 configured slot0:xcpa218-2 pcpa default slot0:xcpa28-0 Note In Cisco IOS Release 12.1(5)T or later, the filenames of all released HP ESCON PA microcode images use the conventions xcpa28-nn (for example, xcpa28-1). Interim pre-relea

• 9 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview ESCON Cable The ESCON channel interface uses 62.5/125 micrometer, multimode, fiber-optic cable with male duplex connectors at each end (Figure 5). ESCON cables are not available from Cisco. Refer to the ESCON specifications in and contact your cable supplier

• Cisco PA-4C-E 1, 3 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preface Related Documentation Your router, switch, or gateway and the Cisco IOS software running on it contain extensive features and functionality, which are documented in the following resources: • Cisco IOS software: For configuration information and support, refer to the modular configuration and modular command reference publications in the Cisco IOS software configuration documentation set that corresponds to the software release installed on your Cisco hardware. Note You can access Cisco IOS software configuration and hardware installation and m

• Cisco PA-4C-E 1, 37 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA 4109312 bytes copied in 206.344 secs (19948 bytes/sec) Note In the preceding example, the exclamation points (!) appear as the file is downloaded, and the “c” characters signify calculation of the checksum, which is a verification that the file has been correctly downloaded to the Flash memory card. Using Additional Flash Memory Commands There are additional commands related to the bootflash Flash memory in the Cisco 7200 series router (call

• Cisco PA-4C-E 1, 18 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Electrical Equipment Guidelines Follow these basic guidelines when working with any electrical equipment: • Before beginning any procedures requiring access to the chassis interior, locate the emergency power-off switch for the room in which you are working. • Disconnect all power and external cables before moving a chassis. • Do not work alone when potentially hazardous conditions exist and never assume that power has been disconnected from a circuit; always check. • Do not perform any action t

• Cisco PA-4C-E 1, 25 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Attaching the HP ESCON PA to the Channel Caution We recommend that an authorized service representative or other qualified service person perform the following procedure. To prevent hardware problems with your host processor, all the channel connections must be tight. A loose connection can cause the host processor or its channel to halt. Every cable must be tightly seated in its

• 17 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Varning! VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfa

• Cisco PA-4C-E 1, 34 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Step 4 Reconfigure the router, as necessary, to use the HP ESCON PA microcode image stored in the Flash memory card in slot 0 or slot 1, or in the SanDisk memory device in disk 0 or disk 1. Step 5 Save your running configuration to a TFTP server, Flash memory, or SanDisk memory. Step 6 Perform a microcode reload. Configuring the HP ESCON PA Microcode This section describes how to modify the startup configuration to load different microcode images at startup, or to change existing configuration instructions and re-enable the system default. At syst

• Cisco PA-4C-E 1, 23 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Removing and Installing Port Adapters Port Adapter Removal and Installation In this section, the illustrations that follow give step-by-step instructions on how to remove and install port adapters. Although the procedures may refer to a particular type of port adapter, the steps are the same for installing and removing all types of port adapters. This section contains the following illustrations: • Cisco 7200 Series Routers and Cisco 7200 VXR Routers—Removing and Installing a Port Adapter, page 24 Caution When performing the followi

• Cisco PA-4C-E 1, 31 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Using the show diag Command Display the type of port adapter installed in your system using the show diag command. Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only. Cisco 7200 Series and Cisco 7200 VXR Series Routers—Example Output of the show diag Command Following is an example of the show diag command from a

• Cisco PA-4C-E 1, 12 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Preparing for Installation This section describes the general equipment, safety, and site preparation requirements for installing the HP ESCON PA. It also includes microcode overview information.This section contains the following subsections: • Required Tools and Equipment, page 12 • HP ESCON PA Microcode Overview, page 12 • Hardware and Software Requirements, page 13 • Checking Hardware and Software Compatibility, page 14 • Safety G

• Cisco PA-4C-E 1, 5 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview Overview This section describes the HP ESCON PA, including channel attachment, the LED functions, the memory and cable requirements, and contains the following subsections: • Port Adapter Overview, page 5 • ESCON Specifications, page 7 • LEDs, page 7 • ESCON Cable, page 9 • Port Adapter Slot Locations on the Supported Platforms, page 9 • Identifying Interface Addresses, page 10 Port Adapter Overview The HP ESCON PA is a high-speed (100 bandwidth points) port adapter for Cisco 7200 series routers, including the Cisco 7200 VXR routers, that sup

• Cisco PA-4C-E 1, 30 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA X.25 software, Version 3.0.0. 4 Ethernet/IEEE 802.3 interface(s) 3 FastEthernet/IEEE 802.3 interface(s) 2 IBM channel interface(s) 125K bytes of non-volatile configuration memory. 20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 4096K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x100 Using the show controllers Commands Display all the current interface processors and their interfaces using the show controllers command. Note The outputs

• Cisco PA-4C-E 1, 40 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA This document is to be used in conjunction with the documents listed in the Preparing for Installation section. Copyright © 2003-2007 Cisco Systems, Inc. All rights reserved. Printed in the USA on recycled paper containing 10% postconsumer waste. CCVP, the Cisco Logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live

• Cisco PA-4C-E 1, 27 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Configuring the HP ESCON PA Interface After you verify that the new HP ESCON PA is installed correctly, use the configure command to configure the new interfaces. The enabled LED (EN) goes on when the port adapter is installed correctly (Figure 3). Before you begin to configure the interface, be prepared with the following information: • Protocols and encapsulations you plan to use on the new interfaces

• Cisco PA-4C-E 1, 38 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA In the squeeze command display output, the displayed characters have the following meaning: • The character “e” means the Flash memory special location has been erased, which occurs before a write operation. • The character “b” means that the data that is about to be written to this special location has been temporarily copied. • The character “E” signifies that the sector that wa

• Cisco PA-4C-E 1, 6 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Overview You can install the HP ESCON PA in any of the available port adapter slots in a Cisco 7200 series router. Figure 2 shows an HP ESCON PA installed in port adapter slot 1 of a Cisco 7206. Figure 2 Cisco 7206 with an HP ESCON PA in Port Adapter Slot 1 Note The HP ESCON PA supports online insertion and removal (OIR), which allows you to install or remove an HP ESCON PA while the system is operating

• Cisco PA-4C-E 1, 33 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Configuring the HP ESCON PA Upgrading Your HP ESCON PA Microcode The following sections discuss HP ESCON PA microcode configuration requirements: • How Does HP ESCON PA Microcode Ship?, page 33 • Upgrading the HP ESCON PA Microcode from Cisco.com, page 33 • Configuring the HP ESCON PA Microcode, page 34 For additional information about specific microcode requirements, refer to the “Hardware and Software Requirements” section on page 13. How Does HP ESCON PA Microcode Ship? For the Cisco 7200 series routers, when the HP ESCON PA is ordered as part of a new system, the HP ESCON P

• Cisco PA-4C-E 1, 19 PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration OL-3743-02 Preparing for Installation Class 1 laser products are not considered hazardous. The HP ESCON PA has embedded Class 3a laser LED assemblies operating at a nominal wavelength of 850 nanometer and a maximum potential output power of 1.25 milliwatts. The design of the HP ESCON PA incorporates engineering features including current limiting, which ensures that there is no human access to LED radiation greater than Class 1 under any set of operating, maintenance, or service conditio

Related Products and Documents (Adapter):

Comparable Devices:

Similar Resources:

• Stephen SVG200SP PLUS (36 pages) SVG200SP+ 1 FXS+1 PSTN SIP/IAX ATA User Manual 1 / 36 www.stephen-tele.com SV …

• Acer ARMC_3P (2 pages) ARMC/3PQuick Installation and Setup GuideFor more detailed instructions, please consult the User Manual found on the enclosed CD-ROM. Rev. A March 2007 Connecting Power usingExternal Power AdaptorAn external power supply could beconnected to the ARMC/3P in orderto use the remote power on/off fea-tures provided by the ARMC/3P.To allow the ARMC/3P to operatei …

• Rice Lake 880 Performance Series (6 pages) 880 Performance™ SeriesRelay Option Card InstallationThe Relay Option Card provides four normally open relays for an 880 indicator when installed. The Relay Option Card attaches to the 880 CPU board. Depending on the desired output of the Relay Option Card, SLOT 1 must be configured in the Setpoints Menu (SETPTS) and BIT 1-4 in the Digital I/O Menu (DIGIO) …

• AKG C 1000 S - PPC 1000 & PB 1000 (14 pages) C1000SBEDIENUNGSAN LEITUNG ................................... 2 Bitte vor Inbetriebnahme des Gerätes lesen! USER INSTRUCTIONS ...................................... 16 Please read the manual before using the equipment! MODE D’EMPLOI ............................................. 30 Veuillez lire cette notice avant d’utiliser le système! ISTRUZIONI …

• Epson Stylus Color 660 (66 pages) Color Ink Jet PrinterColor Ink Jet PrinterDaily UseDaily UsePrinted in U.K. 19.7.99Daily Use4010625 BK1-F Rev.04010625 PMS3271-F Rev.04010625 DICF431-F Rev.04010612XXX-00 …

• NETGEAR WG111 54 Mbps Wireless USB 2.0 Adapter WG111 WG111 (2 pages) Start HereFollow these instructions to set up your wireless adapter.These basic setup instructions assume that you will connect to an access point, and youare not using WEP security. Please refer to the online help and the Reference Manual onthe 54 Mbps Wireless USB 2.0 Adapter Resource CD for instructions on configuring WEP,Ad-Hoc mode, or advanced options. …

Comments, Questions and Opinions: