Manualios.com

Sofar ME3000SP Operation & User’s Manual

Sofar ME3000SP Manual Online:

4.9, 682 votes
Sofar ME3000SP User Manual
Sofar ME3000SP User Guide
Sofar ME3000SP Online Manual

Text of Sofar ME3000SP User Guide:

  • 10 4 4mm Allen Key Turn the screw to connect rear panel with inverter 5 Crimping tools Used to crimp power cables 6 Multi-meter Used to check grounding 7 Marker pen Used to mark signs 8 Measuring tape Used to measure distances 9 Level Used to ensure that the rear panel is properly installed 10 ESD gloves Operators wear 11 Safety

  • Sofar ME3000SP, 2 Contents 1. ME3000SP Introduction ........................................................................................................................................... 4 2. Safety Notes ............................................................................................................................................................. 5 2.1 Safety Notes ............................................................................................................................................. 5 2.2

  • Sofar ME3000SP, 20 5.3 Status of ME3000SP Status of ME3000SP Discharging Green light Charging Green light Alarm Red light Discharge ON Check discharge Flashing Charge ON Check charge Flashing Standby Flashing Flashing EPS state ON ON Some events in current event list ON

  • Sofar ME3000SP, 9 Communication cable × 1 Fig. 3 Accessories of ME3000SP 3.3 Installation Environment  Choose a dry, clean, and tidy place, convenient for installation  Ambient temperature range: -25C ~ 60C  Relative humidity: 0 ~ 100% (non-condensed)  ME3000SP shall be installed in a well-ventilated place  No flammable or explosive materials close to ME3000SP  ME3000SP shall be connected to the electrical grid with an overvoltage category III or category II  Max

  • Sofar ME3000SP, 31 2) Autotest STD Select “2. Autotest STD”, then press “OK” to start Auto test STD. The test procedure is same as Autotest Fast, but it’s much more time consuming. 3) PF Time Setting Select “3. PF Time Setting”, then press “OK”. The following will be shown on the display: Set: *. *** s Press “Up” or “Down” to change the 1 st digit, press “OK” to switch to next digit. After changing all digits, press “OK”. 4) QV Time Setting Select “4. QV Time Setting”, then press “OK”. The following will be shown on the display: Set:** s Press “Up�

  • Sofar ME3000SP, 3 6.4.1 Enter setting: ......................................................................................................................................... 26 6.4.2 Event List ................................................................................................................................................ 34 6.4.3 System information interface ................................................................................................................ 35 6.4.4 Software upgrade

  • Sofar ME3000SP, 36 6.4.4 Software upgrade Copy the upgrade firmware to the root directory of SD card. (Note: Ask SOFAR technical support for upgrade firmware & instruction) Select “4. Software Update”, press “OK”, “ input password” is shown. Input the password (”0715”), press “Up” or “Down” to change the 1 st digit, press “OK” to switch to next digit, when “0715” is shown on the screen, press “OK”. ME 3000SP will start to upgrade the software automatically. Detailed Firmware Upgrade Procedure: Step 1 Turn off AC circuit breaker (grid) and DC isolator (battery), t

  • 38 7. Technical Data Model ME3000SP Battery Parameters Battery Type Lead-acid, Lithium-ion Nominal battery voltage 48V Battery voltage range 42 - 58V Recommended battery capacity 200Ah (100 – 500 Ah optional) Recommended storage capacity 9.6 kWh Max charge current 60A Charge current range 0 – 60A programmable Charge curve 3 - stage adaptive with

  • Sofar ME3000SP, 8 Fig. 2 ME3000SP & mounting bracket 3.2 Packing List Inspect the package and fittings carefully before installation. You should have the following fittings: Mounting Bracket × 1 AC terminal × 6 M5 screw × 2 Battery terminal × 2 M6 flat washer × 8 Expansion Bolts × 8 Terminal cap × 4 CT terminal × 2 Current Transformer × 2 User Manual × 1 Warranty card × 1 Quality Certificate × 1

  • Sofar ME3000SP, 28 9) Min. Discharge (V) Select “6. Min. Discharge (V)” and press “OK”. Press “up” or “down” to change the 1 st digit, press “ok” to switch to next digit. Input the value of Min. Discharge (V) per battery specification. Press “OK”. 10) * Empty Discharged (V) (only for DEFAULT battery type) Select “10. Empty Discharged (V)” and press “OK”. Press “up” or “down” to change the 1 st digit, press “ok” to switch to next digit. Input the value of Empty Discharged Voltage per battery specification. Press “OK”. 11) * Full Charged (V) (only for DEFAULT battery type) Select “11. Full C

  • Sofar ME3000SP, 43 ID86 Bat Voltage Low Shut Battery voltage is too low & cause ME3000SP to switch OFF ME3000SP will switch OFF when battery voltage is too low. This is a protection for battery. ID94 Software version is not consistent Contact SOFAR technical support to upgrade software. ID95 CommEEPROMFault The Communication board EEPROM is fault ID95-ID96 are internal faults of ME3000SP, turn OFF the DC isolator & AC circuit breaker, wait f or 5 minutes, then turn ON the DC isolator and turn ON the AC circuit breaker. Check whether the problem is solved. If no, please contact SOFAR technical support. ID96 RTCFault RTC clock chip is fault

  • Sofar ME3000SP, 19 5. Buttons and indicator lights Discharging Status Light Charging Status Light Alarm Light Back Up Down OK Fig 14. Buttons and indicator lights 5.1 Buttons:  press “Back” to the previous screen or enter the main interface;  press “Up” to the upper menu option or value plus 1;  press “Down” to the lower menu option or value minus 1;  Press “OK” to select the current menu option or switch to the next digit. 5.2 Indicator lights:  Discharging status Light(Green)  Discharging light ON: discharging the battery  Charging status Light(Green)  Charging lig

  • Sofar ME3000SP, 32 1) PV generation ~= LOAD consumption ( Δ P < 100W), ME3000SP will stay in Standby state. 2) PV generation > LOAD consumption, the surplus power will be stored in the battery. 3) When the battery is full(or already at Max Charge Power), excess power will be exported to the grid. 4) PV generation < LOAD consumption, ME3000SP will discharge the battery to supply power to load, 5) If PV generation + Battery < LOAD consumption, ME3000SP will import power from the grid. 6) Press “DOWN” button to check current detailed information, press “UP” to get back to main interface.

  • Sofar ME3000SP, 13 4. Electrical Connection  Be aware of electric shock and chemical hazards!  Use a multi-meter to check the DC polarity before connecting the DC power cable between battery & ME3000SP.  It’s recommended to install a rotary DC isolator (100A) between ME3000SP and batteries. Thus, ME3000SP can be securely disconnected during installation/maintenance.  It’s necessary to install a AC circuit breaker (25A) between ME3000SP and electrical grid.  It is very important for system safety and efficient operation to use appropriate cable for electrical connection.  Battery connection: AWG8 or AWG6 cable.  Grid &am

  • Sofar ME3000SP, 26 6.4 Menu In the main interface, press “back” button to enter main menu. The main menu has the following five options: Main Interface Press “Back” “Up” ↑ “Down”↓ 1.Enter Setting 2.Event List 3.System Information 4.Software Update 5.Energy Statistic 6.4.1 Enter setting: 1.Enter Setting Press “OK” “Up” ↑ “Down”↓ 1.Battery Parameter 8.Set Time 2.Clear Energy Data 9.Set EPS Mode 3.Clear Events 10. DRMs0 Control 4.Set Country 11. Auto Test (For Italian Market Only) 5.Set Communication Addr. 12. Work Mode Set 6.Function to Set Country 13. Safety Param. Settings 7.Set Language

  • Sofar ME3000SP, 40 8. Troubleshooting Code Name description solution ID01 GridOVP The power grid voltage is too high If the alarm occurs occasionally, the possible cause is that the electric grid is abnormal occasionally. ME3000SP automatically returns to normal operating status when the electric grid’s back to normal. If the alarm occurs frequently, check whether the grid voltage/frequency is within the acceptable range. If no, contact SOFAR technical support. If yes, check the AC circuit breaker and AC wiring of the ME3000SP. If the grid voltage/frequency is within the acceptable range and AC wiring is correct, while the alarm occurs repeatedly, contact SOFAR

  • Sofar ME3000SP, 15 Fig. 7 Schematic Diagram (ME 3000SP: energy storage add-on to existing renewable system) Step 1: Location of CTa: L wire of incoming mains. Location of CTpv: L wire of PV inverter’s output. Step 2: Use network cable & terminal caps to extend CT wires. Fig. 8 CT wire extension CT wire Extension cable (network cable) ME 3000SP Red Orange / white orange / brown / white brown CT+ Black Green / white green / blue / white blue CT-

  • Sofar ME3000SP, 16 Fig. 9 CT / RS485 / NTC connection Step 3: Loosen 4 screws (part A) using a screwdriver (fig. 9) Step 4: Remove the waterproof cover (part B), loosen the cable gland (part C), then remove the stopper (part G) Step 5: Route CT cable through the cable gland, connect CT cable to CT terminal, then insert CT terminal into corresponding ports. Step 6: one communication cable is provided in the ME3000SP accessory bag. One inverter end, one BAT end. Route the communication cable (inverter end) through the cable gland, insert the 4P4C connector to ME3000SP CAN port. Insert the 8P8C co

  • Sofar ME3000SP, 6 The can lead battery to leak even explode.  The current capacity of DC power cables (from battery to inverter) should be at least 90A. Use short power cables to avoid high voltage drop & power loss.  Use a multimeter to check the batter voltage & polarity before switching ON batteries. Make sure connections are correct according to this manual.  If you want to store the batteries without using them, they should be disconnected from ME3000SP, and be kept in a cool, dry, and ventilated environment.  Battery maintenance operators shall have the knowledge and technical skill for

  • Sofar ME3000SP, 39 Environmental data Ambient temperature range -25C to +60C (derating above +45C) Relative humidity range 0% - 100% (no condensing) Protective class Class I Max operating altitude 2000m Current transformer connection Hard wired General data Noise <25dB Weight 16kg Cooling Natural convection Dimensions (W*H*D) 532 x 360 x 173 mm Display LCD display Warranty 5 years EPS (Emergency Power Supply) data EPS rated power 3000VA EPS nominal voltage/frequency 230V, 50/60Hz EPS rated current 13A THDi <3% Switch

  • Sofar ME3000SP, 27 Select “1. Battery Parameter” and press “OK”, “input password” is shown. Input the password (normal “0001”, advanced ”0715”), press “Up” or “Down” to change the 1 st digit, press “OK” to switch to next digit, when “0001 / 0715” is shown on the screen, press “OK” to enter “Battery Parameter” interface. If “Incorrect, Try Again!” is shown on the screen, press “Back” and input the password again. 1) Battery Type (refer to Set battery type ) Select “1. Battery Type” and press “OK”. Press “up” or “down” to select the battery type. Press “OK”. 2) * Battery

  • Sofar ME3000SP, 30 ↓ Wait Testing 81>S1... ↓ Wait Test 81>S1 OK! ↓ Wait Testing 81>S2… ↓ Wait Test 81>S2 OK! ↓ Wait Testing 81<S1... ↓ Wait Test 81<S1 OK! ↓ Wait Testing 81<S2... ↓ Wait Test 81<S2 OK! ↓ Press “Ok” Auto Test OK! ↓ Press “Down” 59.S1 threshold 253V 900ms ↓ Press “Down” 59.S1: 228V 902ms ↓ Press “Down” 59.S2 threshold 264.5V 200ms ↓ Press “Down” 59.S2: 229V 204ms ↓ Press “Down” 27.S1 thres

  • Sofar ME3000SP, 23 MENU Compatible Batteries 1.PYLON PYLONTECH US2000 PLUS / US2000B Note: Please confirm with representative of PYLONTECH that your battery is compatible with ME3000SP 2. DARFON DARFON 14S31P ESS 3.DEFAULT LEAD ACID / LEAD CRYSTAL / AQUION battery 4. General Lithium All batteries that comply with SOFAR’S BMS CAN communication protocol. 5. Alpha. ESS M48112-P / SMILE-BAT 6. SOLTARO SL-3KWH / SL-1KWH 4)*Set battery capacity (only for DEFAULT battery type) Press “Up” or “Down” to change the 1 st digit, press “OK” to switch to next digit. After changing the battery capacity per your ba

  • 4 1. ME3000SP Introduction ME3000SP is an AC coupled bi-directional battery converter. Customers can purchase batteries & ME3000SP as an energy storage add-on to his/her existing renewable energy system. ME3000SP helps to achieve optimal usage of renewable energy. ME3000SP controls bi-directional flow of electric power, work under auto or time-of-use (TOU) m

  • Sofar ME3000SP, 29 9. Set EPS (Emergency Power Supply) Mode 9. Set EPS Mode 1.EPS Mode Control 1.Enable EPS Mode 2.Disable EPS Mode 2.Set EPS Changeover Time ***S 10. DRMs0 Control (ONLY for Australian Market) Select “10. DRMs0 Control”, press “OK”, “input password” is shown. Input the password “0001”, press “Up” or “Down” to change the 1 st digit, press “OK” to switch to next digit, when “0001” is shown on the screen, press “OK”. After entering DRMs0 control interface, press “up” or “down” to select “1. Enable DRMs0” or “2. Disable DRMs0”, press “OK”. 11. Auto Test (ONLY for Italian Market) Select “11. Auto Test

  • 34 4) Set Passive Mode Select “4. Set Passive Mode”, and then press “OK”. For more detailed information, please ask representative of SOFAR to get a copy of passive mode communication protocol. 13. Safety Param. Settings Select “13. Safety Param. Settings”, press “OK”, “input password” is shown. Input the password “0001”, press “Up” or �

Related Products and Documents (Inverter):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Tascam MD-350 Technical documentation tascam/md-350-632.pdf 30 Jul 2023 2 0.08 Mb
2 Campbell HC2-S3-L Instruction manual campbell/hc2-s3-l-217.pdf 17 Feb 2024 18 0.5 Mb
3 Oce TDS400 Quick reference manual oce/tds400-WA9.pdf 09 Jul 2023 101
4 Ryobi EID1050RB Owner's operating manual ryobi/eid1050rb-P3D.pdf 13 May 2023 9 1.16 Mb
5 Zonet ZWA2112 Product data zonet/zwa2112-H13.pdf 26 Aug 2022 2 0.19 Mb
6 Audiovox SIR-CK3 Installation manual audiovox/sir-ck3-LB9.pdf 27 Sep 2023 20 0.34 Mb

Similar Resources:

  • DAB

    AD 2.2 AC

    (974 pages)
    ISTRUZIONI PER L'INSTALLAZIONE E LA MANUTENZIONE INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE INSTRUCTIONS POUR L'INSTALLATION ET LA MAINTENANCE INSTALLATIONS- UND WARTUNGSANLEITUNGEN INSTRUCCIONES DE INSTALACIÓN Y MANTENIMIENTO РУКОВОДСТВО ПО МОНТАЖУ И ТЕХНИЧЕСКОМУ ОБСЛУЖИВАНИЮ INSTRUCTIES VOOR I …
  • Coopers of Stortford

    Solar Owl

    (2 pages)
    Solar Owl 11579 Instructions for Use Please read and retain these instructions for future reference v001: 28/01/19 Carefully remove the product from the display packaging taking care not to damage the product. To activate the solar sensor, …
  • KROHNE

    OPTIFLUX 6000

    (40 pages)
    Electromagnetic flow sensor for hygienic and sanitary applicationsOPTIFLUX 6000OPTIFLUX 6000OPTIFLUX 6000OPTIFLUX 6000HandbookHandbookHandbookHandbook© KROHNE 12/2011 - 4001723701 - HB OPTIFLUX 6000 R01 enThe documentation is only complete when used in combination with the relevant documentation for the signal converter. …
  • Carel

    Power + PSD1 Series

    (48 pages)
    High Efficiency SolutionsNO POWER & SIGNAL CABLES TOGETHERREAD CAREFULLY IN THE TEXT!Foglio istruzioniTechnical lea etPower +Speed drivePSD1 Series - 230V 12/16APSD1 Series - 400V 18/24A …
  • Toshiba

    TOSVERT VF-S15 series

    (360 pages)
    12345678910111213141516E6581611Read rstISafety precautions ContentsConnectionOperationsSetting parametersMain parametersOther parametersOperation with externalsignalMonitoring the operation statusMeasures to satisfy the standardsPeripheral devicesTable of parameters and dataSpecicationsBefore making a service callInspection and maintenanceWarrantyDispo …
  • Bodine

    ELI-S-10

    (4 pages)
    Bodine © 2018 Signify Holding. All rights reserved.236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-853-5009 • www.bodine.com442294652532ELI SERIES EMERGENCY LIGHTING INVERTERSELI-S-10 10/09/19Installation Instructions NANO INVERTERREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! IMPORTANT SAFEGUARDS !WHEN USING E …

Comments, Questions and Opinions: