Cisco 100 Series Installation Manual

Text of Cisco 100 Series User Guide:

• Cisco 100 Series, CHAPTER Preparing for Installation 2-1 Preparing for Installation 2 This chapter provides safety information and describes the tasks you must perform before you install the LightStream 100 ATM switch. This chapter contains the following sections: • Safety Recommendations • Installation Environmental Conditions • Confirming the Contents of the Shipping Container • LightStream 100 ATM Switch Components Safety Recommendations The following guidelines will help to ensure your general safety and protect the equipment: •

• Cisco 100 Series, 2-2 Cisco LightStream 100 User Guide Safety Recommendations Warning Class 1 laser product. To see this warning in multiple languages, refer to the “Class 1 Laser Product Warning” section in the “Translated Safety Warnings” appendix. Warning Do not stare into the beam or view it directly with optical instruments. To see this warning in multiple languages, refer to the “Laser Beam Warning” section in the “Translated Safety Warnings” appendix. Maintaining Safety with Electricity Follow these guidelines when working on equipment powered by electricit

• Preparing for Installation 2-3 Safety Recommendations • Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, and missing safety grounds. • If an electrical accident occurs, proceed as follows: — Use caution; do not become a victim yourself. — Turn off power to the system. — If possible, send another person to get med

• Cisco 100 Series, 2-4 Cisco LightStream 100 User Guide Installation Environmental Conditions Installation Environmental Conditions Install the LightStream 100 ATM switch in an area that meets the following conditions: 1 Make sure the LightStream 100 switch remains operational within the temperature and humidity limits shown in Table 1-3. 2 Allow the following minimum vacant space surrounding the LightStream 100 switch to ensure proper heat radiation: — 10 cm (approximately 4 inches) or more—sides — 10 cm (approximately 4 inches) or more—front and rear — 10 cm (approximately 4 inches) or more—top 3 Make sure the installation site mee

• Cisco 100 Series, Preparing for Installation 2-5 LightStream 100 ATM Switch Components • Center card (P-8X55-A) • Processor (PROC) card (FSB3523GX, P-8X0R) • Gateway Packet Assembler/Disassembler (GWPAD) card (P-8X86[002]) • Fans (three units) • Power supply • Slot covers (16 units) • Shielded power cable (one unit) The LINF card box contains the LINF card set (a LINF card and front panel with window): • STS-3c/STM-1 LINF card (P-8X79, P-8X0K) • Transparent Asynchronous Transmitter/Receiver Interface (TAXI) LINF card (P-8X31, P-8X85) Note The

• Cisco 100 Series, 2-6 Cisco LightStream 100 User Guide LightStream 100 ATM Switch Components Figure 2-1 LightStream 100 ATM Switch Front Panel H2410 Ethernet connection EIA/TIA-232 Operator LEDs (16) Reset button Run LED Status LED Failure LED LEDs

• Cisco 100 Series, 2-8 Cisco LightStream 100 User Guide LightStream 100 ATM Switch Components Figure 2-3 LightStream 100 ATM Switch Internal View Fan BCONV : Bus Converter GWPAD : Gateway Packet Assembler/Disassembler LINF : Line Interface PROC : Processor VME : Versa Module Eurocard Motherboard Power supply PROC card (VME) LINF card BCONV card Center card Fan Fan GWPAD card H2587

• Cisco 100 Series, Preparing for Installation 2-9 LightStream 100 ATM Switch Components Figure 2-4 Expanded Internal View (Motherboard) CLKGEN Motherboard ATOM SW : Asynchronous Transfer Mode Output-Buffer Modular Switch CLKGEN : Clock Generator DMUX : Demultiplexer GWPAD : Gateway Packet Assembler/Disassembler LINF : Line Interface MUX : Multiplexer MUX/DMUX Subboard ATOM switch LINF card GWPAD card H2567

More Instructions:

	Cisco 100 Series Regulatory compliance and safety information manual 30-03-2023 28	DOWNLOAD
	Cisco 100 Series Installation manual 29-08-2022 76	DOWNLOAD
	Cisco 100 Series Quick start manual 19-01-2023 12	DOWNLOAD
	Cisco 100 Series Quick start manual 13-06-2023 12	DOWNLOAD

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• ADC Active Digital Signal Cross-Connect ASX (4 pages) www.adc.com • +1-952-938-8080 • 1-800-366-3891Spec SheetASX Active Digital Signal Cross-ConnectPart of ADC KRONE’s innovative family of active digital signal cross-connect products, the ASX fully integrates an SDH multiplexer with a FlexDSX® cross-connect chassis. The product allows easy migration of 2 Mbit equipment to next generation equipment, as …

• Martin Audio MA900 (19 pages) Martin Audio – MA900 AmplifierENGLISH1CONTENTS (ENGLISH) Page No1 CONTENTS MA900 USER GUIDE 12APPROVALS 23WARNINGS 23.1 EXPLANATION OF GRAPHICAL SYMBOLS 23.2 WARNING 23.3 CAUTION 23.4 IMPORTANT SAFETY INSTRUCTIONS 23.5 USER RESPONSIBILITY 33.5.1 LOUDSPEAKER DAMAGE 33.5.2 SPEAKER OUTPUT HAZARD 33.5.3 RADIO INTERFERENCE 34 INTRODUCTION 44.1 UNPACKING 44 …

• Robertshaw 5500-103M (2 pages) INSTALLATION DATA5500 M SERIES INFINITE SWITCH KITThe Robertshaw®switch designed to replace the current VSI (INF) switch.� …

• Avenview DVI-GS3-2 (13 pages) www.avenview.com 1 DVI-GS3-2 1080p on DVI monitor User’s Guide © 2007 Avenview™ Inc. All rights reserved. The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with respect to the accuracy or completeness of …

• Eaton 600 A 35 kV Class (4 pages) 600 A 35 kV class insulated protective capDescriptionEaton meets the full requirements of IEEE Std 386™-2006 standard - Separable Insulated Connector Systems, with its Cooper Power™ series 600 A, 35 kV Class insulated protective pap, providing an insulated, fully shielded submersible protection for energized 35 kV Class deadbreak interfaces. The cap is r …

• SMC Networks ZSE3 Series (3 pages) Z/ISE3-TFK26GB-AInstallation & Maintenance ManualDigital Pressure SwitchSeries ZSE3 / ISE31. Safety InstructionsIf instructions are not followed there is apossibility of serious injury or loss of life.If instructions are not followed there is apossibility of injury or equipment damage.1. Safety Instructions (continued)In extreme conditions, there is a po …

Comments, Questions and Opinions: