Avaya X330WAN Operation & User’s Manual
|
Avaya X330WAN, Chapter 3 Initial Configuration 24 Avaya X330WAN User’s Guide For more information, refer to "Priority DLCI" on page 46. 18 Configure an IP address for the Sub-interface using the ip address <ip address> <mask> [<admin state>] command. 19 Type exit to return to Supervisor mode. 20 Repeat step 3 through step 6 to configure additional Frame Relay Sub-interfaces on the same Frame Relay interface. Note: If the Unframed framing option was selected in step 3 for an E1 port, a Channel Group is automatically created comprising the entire E1 bandwidth. This Channel Group has the number ‘0’, and for all the subsequent configuration f
Avaya X330WAN, Chapter 6 X330WAN CLI Commands 104 Avaya X330WAN User’s Guide show banner post-login Use the show banner post-login command to display the post-login banner. Syntax show banner post-login Example X330WAN-2USP-1(super)# show banner post-login show boot bank Use the show boot bank command to display the software bank from which the device boots at the next boot process. Syntax show boot bank Example X330WAN-2DS1-1(super)# show boot bank Boot bank set to bank-a show copy status Use the show copy status command
Avaya X330WAN, Chapter 4 Operational Concepts and Configuration Examples 60 Avaya X330WAN User’s Guide Configuration Example for Site A The following is the configuration procedure for the X330WAN-2USP, as shown in Figure 4.10. Commands with footnotes are described at the end of the configuration procedure. • Loopback and PMI interfaces configuration: X330WAN-2USP-1(super)# interface Loopback 1 X330WAN-2USP-1(super-if:Loopback1)# ip address 10.10.10.10 24 The Primary management interface has changed. Please copy the running configuration to the start-up configuration file, and reset the device. X330WAN-2USP-1(super-if:Loopback1)# exit X330WAN-2USP-1(super)# copy running
Avaya X330WAN, General: Device Commands Avaya X330WAN User’s Guide 103 set time server Use the set time server command to set the TIME server address. Syntax set time server <ip address> Parameters set timezone Use the set timezone command to assign a timezone name and to set the time difference of your WAN relative to the Coordinated Universal Time (UTC/GMT). The minutes parameter can only be set to 30. Syntax set timezone <zone name> <hours|hours:min> Parameters Example X330WAN-2DS1-1(super)# set timezone GMT -3:30 Timezone set to 'GMT', offset
Avaya X330WAN, Enhanced Routing Capabilities Avaya X330WAN User’s Guide 35 Enhanced Routing Capabilities This section describes the following X330WAN routing features: • Static Route Configuration • Export Default Metric • OSPF Dynamic Cost Support • RIP Distribution Access Lists • Fragmentation and Reassembly The following configuration examples integrating the above concepts are provided: • Configuring X330WAN to Connect Branch Offices to Headquarters • Configuring the X330WAN for use with an External Fir
Chapter 6 X330WAN CLI Commands 156 Avaya X330WAN User’s Guide MTU 1500 bytes, Bandwidth 100000 Kbit Reliability 255/255 txLoad 1/255 rxLoad 1/255 Encapsulation ARPA Link status trap disabled Full-duplex, 100Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, Last output 00:00:08 Last clearing of 'show interface' counters 00:06:24 5 minute input rate 81966 bits/sec,
Avaya X330WAN, Chapter 6 X330WAN CLI Commands 96 Avaya X330WAN User’s Guide erase startup-config Use the erase startup-config command to erase the NVRAM startup configuration. Syntax erase startup-config get time Use the get time command to retrieve the time from the network. Syntax get time Example X330WAN-2DS1-1(super)# get time Time is being acquired from server 0.0.0.0! hostname Use the hostname command to change the Command Line Interface (CLI) prompt. The current device number always appears at the end of the prompt. Use the no form of this command to return the CLI prompt to its default. Syntax [no] hostname [<hostname_string>]
Avaya X330WAN User’s Guide 227 Appendix B Embedded Web Manager The Embedded Web Manager for X330WAN provides the following: • Expansion module configuration. • E1/T1/USP port configuration. • Channel group management. • Channel group wizard. • Routing configuration. • Backup interfaces configuration. • Frame Relay parameters configuration. System Requirements Minimum hardware and
Avaya X330WAN, General: Device Commands Avaya X330WAN User’s Guide 105 show dev log file Use the show dev log file command to display the encrypted device’s log file. Syntax show dev log file show erase status Use the show erase status command to view the status of the Erase Startup Configuration operation. Syntax show erase status show image version Use the show image version command to display the software version of the image on both memory banks of the device. Syntax show image version Example X330WAN-2DS1-1(super)# show image version Bank Version ---- ------- A 3.9.7
Avaya X330WAN, Layer 3 CLI Commands Avaya X330WAN User’s Guide 191 ip vrrp timer Use the ip vrrp timer command to set the virtual router advertisement timer value (in seconds) for the virtual router ID. The no form of this command restores the default value. Syntax [no] ip vrrp <vr-id> timer <value> Parameters Example To set the virtual router advertisement timer value for virtual router 3 to 2: X330WAN-2DS1-1(configure)# ip vrrp 3 timer 2 network (Router-OSPF context) Use the network command to enable OSPF in this network. The no form of t
Avaya X330WAN, Interface Serial CLI Commands Avaya X330WAN User’s Guide 129 show controllers remote Use the show controllers remote command to display far end performance data through an FDL message. Note: This command is used when the fdl at&t option is defined. Syntax show controllers remote <port> <fdl-request-type> Parameters Example X330WAN-2DS1-1(super)# show controllers remote 1 1h-data shutdown (Controller context) Use the shutdown command to shutdown the E1/T1 link. This has the effect of administratively bringin
Avaya X330WAN, Chapter 4 Operational Concepts and Configuration Examples 44 Avaya X330WAN User’s Guide The following is the configuration procedure for the X330WAN, as shown in Figure 4.6: X330WAN-2DS1-1(super)# interface Loopback 1 Done! X330WAN-2DS1-1(super-if:Loopback1)# ip address 10.10.10.10 32 The Primary management interface has changed. Please copy the running configuration to the start-up configuration file, and reset the WAN router. Done! X330WAN-2DS1-1(super-if:Loopback1)# exit X330WAN-2DS1-1(super)# copy running-config startup-config X330WAN-2DS1-1(super)# reset X330WAN-2DS1-1(super)# controller e1 1 Done! X330WAN-2DS1-1(super-controller:1)# channel-
Avaya X330WAN, Enhanced Routing Capabilities Avaya X330WAN User’s Guide 41 Configuration Example for Branch Office 1 The following is the configuration procedure for the X330WAN in Branch Office 1, as shown in Figure 4.5: X330WAN-2DS1-1(super)# interface Loopback 1 Done! X330WAN-2DS1-1(super-if:Loopback1)# ip address 10.10.10.10 32 The Primary management interface has changed. Please copy the running configuration to the start-up configuration file, and reset the WAN router. Done! X330WAN-2DS1-1(super-if:Loopback1)# exit X330WAN-2DS1-1(super)# copy running-config startup-config X330WAN-2DS1-1(super)# reset X330WAN-2DS1-1(super)# controller t1 1 Done! X330WAN-2DS1-1(super-controller:1)
Avaya X330WAN, Interface Serial CLI Commands Avaya X330WAN User’s Guide 139 show queueing Use the show queueing command to display the priority queue size, in packets. Syntax show queueing [Serial <if-number>] Parameters Example X330WAN-2DS1-1(super)# show queueing Serial 1 shutdown (X330WAN-2USP Serial interface context) Use the shutdown command to shutdown the selected interface. The no form of this command activates the selected interface. Note: This command is executed from the Serial, Loopback, Fast Ethernet, and
Avaya X330WAN, General: Device Commands Avaya X330WAN User’s Guide 93 copy tftp SW_image Use the copy tftp SW_image command to update the software image and the device manager applications of a designated device. To use this command, you need to have an active TFTP server and create a file into which to download the data. If Avaya MultiService Network Manager is running, an additional tftp server is not required. Syntax copy tftp SW_image <sw-image-file> EW_archive <EmWeb_File> <ip_address> copy tftp SW_image &
Contents Avaya X330WAN User’s Guide v show module-identity .............................................................................106 show running-config ................................................................................106 show snmp ................................................................................................106 show startup-config ......
Configuring the X330WAN Avaya X330WAN User’s Guide 27 •v = VLAN number Checking the Loopback, Fast Ethernet, E1/T1/USP, IP Interface Configuration After configuring the new interface, you can perform the following tests to verify that the new interface is operating correctly. • For the X330-2DS1, use the show controllers <port> command to display the status of
Avaya X330WAN, Controller CLI Commands (X330WAN-2DS1 Only) Avaya X330WAN User’s Guide 127 Remote alarm Any alarms detected by the controller are displayed. The possible alarms are: • Transmitter is sending remote alarm. • Transmitter is sending alarm indication signal (AIS). • Receiver has loss of signal. • Receiver is receiving AIS. • Receiver has loss of frame. • Receiver has remote alarm. • Receiver has no alarms. • Receiver has a major alarm. Framing Shows the current framing type. The def
Avaya X330WAN, X330W-2USP Front Panel and LEDs Avaya X330WAN User’s Guide 13 X330W-2USP Front Panel and LEDs The front panel of the X330W-2USP has a column of two LEDs for each Serial port in the access router module, and an Operational LED displaying module status. There is also a Fast Ethernet port, and a Console port for directly connecting a terminal. Between the LEDs and the Console port there is a RST/FIV button for manually resetting the module. Figure 2.2 X330W-2USP Front Panel Table 2.1 describes the LEDs on the front panel of the X330W-2USP. Table 2.2 X330W-2USP LED De
Avaya X330WAN, Interface Serial CLI Commands Avaya X330WAN User’s Guide 131 clear ip tcp header-compression (PPP interface) Use the clear ip tcp header-compression command to clear TCP compression statistics either for all enabled interfaces or for a specific interface. To clear for all enabled interfaces, do not enter an interface type and number. Syntax clear ip tcp header-compression [<interface type> <interface number>] Parameters Example X330WAN-2USP-1(super)# clear ip tcp header-compression description (X330WAN-2USP Serial interface context) Use the descript
Avaya X330WAN, Installing the On-Line Help and Java Plug-In on your Web Site Avaya X330WAN User’s Guide 231 Installing from the Avaya P330 Documentation and Utilities CD To install the Java plug-in from the CD: 1 Close all unnecessary applications on your PC. 2 Insert the “Avaya P330 Documentation and Utilities” CD into the CD drive. 3Click Start on the task bar. 4Click Run. 5Type x:\emweb-aux-files\plug-in_1_3_1_02.exe where x is the CD drive letter. 6 Follow the instructions on the screen. Installing from the Avaya Site To install the Java plug-in from the Avaya web site, click the appropriate li
Avaya 4500 VA Network Router Configuration manual
4500 VA |
Avaya 4550T-PWR+ Network Router Fundamentals
4550T-PWR+ |
Avaya NN48500-598 Network Router Engineering
NN48500-598 |
Avaya ERS 3500 Network Router Quick setup manual
ERS 3500 |
Avaya X330W-2DS1 Network Router Operation & user’s manual
X330W-2DS1 |
Avaya Secure Router 3120 Network Router Installation manual
Secure Router 3120 |
Avaya 4500 VA Network Router Installation manual
4500 VA |
Avaya ERS 1600 Network Router Technical configuration manual
ERS 1600 |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Biostar | I86PE-A7 | Operation & user’s manual | biostar/i86pe-a7-373.pdf | 13 Jun 2023 | 27 | 1.12 Mb |
2 | Philips | Alto Plus Slimline 8 | Specifications | philips/alto-plus-slimline-8-L3X.pdf | 26 Dec 2023 | 2 | 0.19 Mb |
3 | Logitech | Folio S310 | Setup manual | logitech/folio-s310-1W1.pdf | 15 Apr 2023 | 12 | |
4 | BlueTrek | Metal | Supplementary manual | bluetrek/metal-596.pdf | 04 Oct 2023 | 1 | 0.04 Mb |
5 | Kenmore | 253 Series | Use and care manual | kenmore/253-series-V7O.pdf | 11 Dec 2023 | 25 | |
6 | Garmin | Gladiator TR-1 | Installation & setup manual | garmin/gladiator-tr-1-83S.pdf | 10 Dec 2022 | 53 | 2.06 Mb |
Comnet
QUICK START GUIDE CNGE24FX12TX12MS[POE]Industrial Grade Managed Ethernet Switch w/ 12 × 100/1000Base-FX + 12 × 10/100/1000Base-TX Ports w/ Optional 30W PoEThe ComNet CNGE24FX12TX12MS[POE] has twelve 100/1000Base-FX SFP* ports and twelve 10/100/1000Base-TX ports. All SFP ports utilize ComNet SFP modules for fiber and connector type and distance. The IEEE8 …
CNGE24FX12TX12MSPOE(8 pages) |
TP-Link
Power on the modem, and then wait about 2 minutes for it to restart.2Choose your device typeRouterRange ExtenderArcher AX6000Set Up the Network1. Connect your device to the router wirelessly or with an Ethernet cable.New Password:Let’s Get StartedConrm Password:http://tplinkwi.netMethod TWO: Via a Web Browser2. Launch a web browser, and enter http:// …
Archer AX55(2 pages) |
Craftsman
612547-243SEARSOWNERSMANUALMODEL NO315,17560CAUTIONRead Rules forSafe Operationand InstructionsCarefullySAVE THISMANUAL FORFUTURE REFERENCEROUTERDOUBLE INSULATEDIntroductionOperationMaintenanceRepair PartsDesigned exclusively for and sold only bySEARS, ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684612547-24311.85PRINTED IN U.S.A,
…
315.17560(12 pages) |
Makita
GBRouterElectronic Router Instruction ManualFDéfonceuseDéfonceuse électronique Manuel d’instructionsDOberfräseElektronische Oberfräse BetriebsanleitungIFresaFresa elettronicaIstruzioni per l’usoNLBovenfreesElektronische bovenfreesGebruiksaanwijzingEMáquina para fresarMáquina para fresar electrónica Manual de instruccionesPFresadoraFresadora elect …
3612(60 pages) |
H3C
H3C MSR Router Series Comware 7 OAA Configuration Guide New H3C Technologies Co., Ltd. http://www.h3c.com Software version: MSR-CMW710-R0615 Document version: 6W202-20200321
…
MSR Series(11 pages) |
Edimax
How to Secure my wireless network on Edimax Wireless Router Introduction TThhiiss FFAAQQ iiss aapppplliieedd ttoo tthhee bbeellooww EEddiimmaaxx mmooddeellss aanndd ooppeerraattiioonn ssyysstteemmss.. MMooddeellss:: BBRR--66222288nnSS,, BBRR--66222288nnCC OOppeerraattiioonn SSyysstteemm:: WWiinnddoowwss XXPP,, WWiinnddoowwss VViissttaa, …
BR-6228nS(2 pages) |
Polaroid Flat Panel TV 20070918User Guide: Polaroid 20070918 (Q6PR65, Upd.29th Jan 2024) 20070918, 48 |
Dimplex Heater 403TSDimplex Heater 403TS Installation and operating instructions 403TS, 4 |
Kontron Motherboard ECX-KBL-U#224C1G ECX-KBL-U: Kontron Motherboard Owner Documentation ECX-KBL-U, 78 |
GMC Nail Gun ATBR1650-3PKNail Gun Instruction manual (GMC ATBR1650-3PK) ATBR1650-3PK, 47 |
Jersey Jack Pinball Pinball Machine Pirates of the CaribbeanJersey Jack Pinball Pirates of the Caribbean User Manual (Operation manual), @T6P77M Pirates of the Caribbean, 359 |
AKG Transmitter SO 40 SNAPONSO 40 SNAPON (Transmitter ePDF User Manual, #U6D9J4) SO 40 SNAPON, 40 |
Porta-Nails Nail Gun 402402 Owner's manual - 265513 402, 12 |
EnGenius Wireless Access Point ENH900EXTEnGenius ENH900EXT User Manual (Operation & user’s manual), @48W4R6 ENH900EXT, 2 |
AOR Receiver ARD9900AOR Product Manual: ARD9900 PDF Operating manual - RA3278 ARD9900, 38 |
Striper Boat Seaswirl SeriesStriper Boat Owner's manual (File: striper-seaswirl-series-boat-148, Sunday 03-12-2023) Seaswirl Series, 148 |
JVC CD Player KD-S71RCD Player Instructions manual (JVC KD-S71R) KD-S71R, 32 |
elero Control Unit VarioTecPDF User Guide (@61F9C9), elero VarioTec Control Unit (11/08/2023) VarioTec, 8 |