Manualios.com

Cisco IE-3000-8TC Message Manual

Cisco IE-3000-8TC Manual Online:

4.85, 695 votes
Cisco IE-3000-8TC User Manual
Cisco IE-3000-8TC User Guide
Cisco IE-3000-8TC Online Manual

Text of Cisco IE-3000-8TC User Guide:

  • 2-65 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SW_VLAN Messages SW_VLAN Messages This section contains the VLAN manager messages. The VLAN manager receives information from the VTP and enables the proper VLAN membership on all interfaces through the port manager. Error Message SW_VLAN-3-MALLOC_FAIL: Failed to allocate [dec] b

  • 2-56 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SPANTREE Messages Error Message SPANTREE-2-RECV_1Q_NON_1QTRUNK: Received 802.1Q BPDU on non 802.1Q trunk [chars] [chars]. Explanation The listed interface on which a Shared Spanning Tree Protocol (SSTP) BPDU was received was in trunk mode but was not using IEEE 802.1Q e

  • Cisco IE-3000-8TC, 2-70 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SW_VLAN Messages Error Message SW_VLAN-4-VTP_INVALID_EVENT_DATA: VLAN manager received bad data of type [chars] value [dec] while being called to handle a [chars] event. Explanation The VLAN manager received invalid data from the VTP configuration software. The first [chars] is the data type, [dec] is the value of that data, and the second [chars] is the VTP event. Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the error by using the Output In

  • 2-71 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SWITCH_QOS_TB Messages Error Message SW_VLAN-6-VLAN_DAT_CACHE_EXISTS: Unexpected vlan.dat cache exists. Removing the cache and continuing the sync with new set. Explanation This message rarely appears and does not affect switch functionality. Recommended Action No acti

  • Cisco IE-3000-8TC, 2-34 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures PHY Messages Error Message PHY-4-MODULE_DUP: SFPs in [chars] and in [chars] have duplicate vendor-id and serial numbers. Explanation The SFP module was identified as a Cisco SFP module, but its vendor ID and serial number match that of another SFP module in the system. The first [chars] is the interface in which the SFP module is installed, the second [chars] is the interface where the duplicate SFP module is installed. Recommended Action Copy the messa

  • Cisco IE-3000-8TC, 2-60 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SPANTREE Messages Error Message SPANTREE-6-PORT_STATE: Port [chars] instance [dec] moving from [chars] to [chars]. Explanation The port state changed. The first [chars] is the interface name. [dec] is the spanning-tree instance ID. The second [chars] is the old state (such as listening, learning, or forwarding, and so forth), and the third [chars] is the new state. Recommended Action No action is required. Error Messa

  • Cisco IE-3000-8TC, 2-73 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures UDLD Messages Error Message TCAMMGR-3-REGION_ERROR: cam region [dec] is invalid. Explanation The CAM region is not valid. [dec] is the region. Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to look for similar reported problems. If you still require assistance, open a case with the TAC, or contact your Cisco technical support representative, and provide the representative with the gathered infor

  • Cisco IE-3000-8TC, 2-69 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SW_VLAN Messages Error Message SW_VLAN-4-VLAN_CREATE_FAIL: Failed to create VLANs [chars]: [chars]. Explanation The specified VLANs could not be created. The port manager might not have completed the VLAN creation requests because the VLANs already exist as internal VLANs. The first [chars] is the VLAN ID, and the second [chars] describes the error. Recommended Action Check the internal VLAN usage by using show vlan internal usage privileged EXEC command, reconfigure the feature that is using the internal VLANs, and try to create the VLANs again. If this messag

  • Cisco IE-3000-8TC, CHAPTER 2-1 Cisco IE 3000 Switch System Message Guide OL-13020-01 2 Message and Recovery Procedures This chapter describes the Cisco IE 3000 switch system messages in alphabetical order by facility. Within each facility, the messages are listed by severity levels 0 to 7: 0 is the highest severity level, and 7 is the lowest severity level. Each message is followed by an explanation and a recommended action. The messages listed in this chapter do not include the hostname or the date/time stamp designation that displays only if the software is configured for system log messaging. The chapter includes these message facilities: • ACLMGR Messages,

  • Cisco IE-3000-8TC, 2-29 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures IDBMAN Messages Error Message IDBMAN-3-INVALIDAGGPORTBANDWIDTH: [chars]([dec] / [dec]) has an invalid bandwidth value of [dec]. Explanation There is an internal error that caused an invalid bandwidth to be used for an aggregate port. [chars] is the port-channel name. The ([dec] / [dec]) are the slot and port numbers (slot/port). The last [dec] is the bandwidth. Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to look for similar

  • Cisco IE-3000-8TC, 2-11 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures DOT1X Messages Error Message DHCP_SNOOPING-6-VLAN_NOT_SUPPORTED: Vlan not supported. [dec] bindings ignored. Explanation The specified number of bindings were ignored when the switch read the database file because the VLAN is no longer configured on the switch. [dec] is the number of bindings that the switch ignores. Recommended Action No action required. DOT1X Messages This section contains the IEEE 8

  • Cisco IE-3000-8TC, 2-52 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures RMON Messages RMON Messages This section contains the remote network monitoring (RMON) messages. Error Message RMON-5-FALLINGTRAP: Falling trap is generated because the value of [chars] has fallen below the falling-threshold value [dec]. Explanation A falling trap has been generated. The value of the specified MIB object has fallen below the falling threshold value. [chars] is the MIB object, and [dec] is the threshold value. Recommended Action Take appropriate action on the specified MIB object. Error Message RMON-5-RISINGTRAP: Rising trap is gene

  • Cisco IE-3000-8TC, 2-3 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures ACLMGR Messages Error Message ACLMGR-2-NOVLB: Cannot create memory block for VLAN [dec]. Explanation The ACL manager could not save per-VLAN information needed for its correct operation. Some per-interface features, such as access groups or VLAN maps, will not be configured correctly. [dec] is the VLAN ID. Recommended Action Use a less complicated configuration that requires less memory. Error Message ACLMGR-2-NOVMR: Cannot create VMR data structures for access list [chars]. Explanation The

  • Cisco IE-3000-8TC, 2-43 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures PM Messages Error Message PM-4-INACTIVE: putting [chars] in inactive state because [chars]. Explanation The port manager has been blocked from creating a virtual port for the switch port and VLAN, causing the port to be in an inactive state. The reason for this condition is specified in the error message. The first [chars] is the interface name, and the second [chars] is the reason. Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve

  • 2-53 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SPANTREE Messages SPANTREE Messages This section contains the spanning-tree messages. Error Message SPANTREE-2-BLOCK_BPDUGUARD: Received BPDU on port [chars] with BPDU Guard enabled. Disabling port. Explanation A bridge protocol data unit (BPDU) was re

  • Cisco IE-3000-8TC, 2-4 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures ACLMGR Messages Error Message ACLMGR-3-INSERTFAIL: Insert of access-map [chars] #[dec] into [chars] label [dec] failed. Explanation The system ran out of CPU memory when trying to merge sections of an access map. The first [chars] is the map name, and the second [chars] is the direction in which the map was applied. The first [dec] is the entry number, and the second [dec] is the label number. Recommended Action Reduce other system activity to ease memory demands. For example, remove any ACLs that have been defined but are not now used. Use simpler ACLs wit

  • Cisco IE-3000-8TC, 2-13 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures DOT1X_SWITCH Messages Error Message DOT1X_SWITCH-5-ERR_PRIMARY_VLAN_NOT_FOUND: Attempt to assign VLAN [dec], whose primary VLAN does not exist or is shutdown, to 802.1x port [chars] Explanation An attempt was made to assign a private VLAN whose primary VLAN does not exist or is shut down. [dec] is the VLAN, and [chars] is the port. Recommended Action Make sure the primary VLAN exists and is not shut down. Verify that the private VLAN

  • Cisco IE-3000-8TC, 2-41 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures PM Messages with the TAC, or contact your Cisco technical support representative, and provide the representative with the gathered information. For more information about these online tools and about contacting Cisco, see the “Error Message Traceback Reports” section on page 1-4. Error Message PM-4-BAD_VLAN_ID: an invalid vlan id ([dec]) was detected. Explanation The port manager detected an invalid request. [dec] is the VLAN ID. Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the error by

  • Cisco IE-3000-8TC, 2-47 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures QOSMGR Messages QOSMGR Messages This section contains the quality of service (QoS) manager messages. An incorrect QoS setting causes these messages. Error Message QOSMGR-3-FEATURE_NOT_FOUND: Cannot find feature for [chars]. Explanation An internal software error has occurred. [chars] is the description of the feature that the software cannot find. Recommended Action Copy the message exactly as it a

  • Cisco IE-3000-8TC, 2-55 Cisco IE 3000 Switch System Message Guide OL-13020-01 Chapter 2 Message and Recovery Procedures SPANTREE Messages feature is mainly used to detect unidirectional links. The first [chars] is the loopguard state (enable or disable), the second [chars] is the interface name, and the third [chars] is the spanning-tree instance. Recommended Action Verify that this is the desired configuration for the listed interface. Correct it if this is not the desired configuration; otherwise, no further action is required. Error Message SPANTREE-2-LOOPGUARD_UNBLOCK: Loop guar

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 TEFAL Cool Touch User manual manual tefal/cool-touch-JL4.pdf 13 Jun 2023 6 0.54 Mb
2 KitchenAid KBRS20EVMS - 19.9 cu. Ft. Bottom-Freezer Parts list kitchenaid/kbrs20evms-19-9-cu-ft-bottom-freezer-IHJ.pdf 02 Apr 2023 16
3 CARLO GAVAZZI T2000P Configuration carlo-gavazzi/t2000p-D6M.pdf 09 Mar 2024 24 0.27 Mb
4 Bolens 416 Operator's manual bolens/416-11I.pdf 18 Nov 2023 18 4.12 Mb
5 Haier FTM140GG - 10-03 Operation & user’s manual haier/ftm140gg-10-03-4N2.pdf 11 Jan 2024 6 0.08 Mb
6 Zanussi ZHT 60 Instructions for use zanussi/zht-60-4O6.pdf 19 Oct 2022 3 0.05 Mb

Similar Resources:

  • Cisco

    4503 - Catalyst Switch

    (23 pages)
    Data Sheet © 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 23 Cisco Catalyst 4500 Series Line Cards Secure, Flexible, Nonstop Communications Product Benefits The Cisco® Catalyst® 4500 Series Switches provide scalable nonblocking Layer 2–4 switching with secure, flexible, nonstop communications, ena …
  • Cisco

    CRS-1 - Carrier Routing System Router

    (232 pages)
    Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0883Cisco IOS XR System Security Configuration Guide for the Cisco CRS-1 RouterCisco IOS XR Software Release 3.9Text Part Number: OL-20382-01 …
  • H3C

    S3100-52P

    (16 pages)
    Operation Manual – QoS H3C S3100-52P Ethernet Switch Table of Contents i Table of Contents Chapter 1 QoS Configuration....................................................................................................... 1-1 1.1 Overview....................................................................................................................... …
  • Zte

    ZXR10 5900E Series

    (104 pages)
    ZXR105900ESeriesAllGigabit-PortIntelligentRoutingSwitchUserManual(IPv4Volume)Version2.8.23.BZTECORPORATIONZTEPlaza,KejiRoadSouth,Hi-TechIndustrialPark,NanshanDistrict,Shenzhen,P .R.China518057Tel:(86)75526771900Fax:(86)75526770801URL:http://ensupport.zte.com.cnE-mail:[email protected]
  • Zte

    ZXR10

    (117 pages)
    ZXR10Router/EthernetSwitchCommandManual(MPLSVolume)Version4.8.22ZTECORPORATIONZTEPlaza,KejiRoadSouth,Hi-TechIndustrialPark,NanshanDistrict,Shenzhen,P .R.China518057Tel:(86)75526771900Fax:(86)75526770801URL:http://ensupport.zte.com.cnE-mail:[email protected]
  • Viking

    PB-100

    (4 pages)
    PB-100PB-100Polling Bridge andPhone Line InterfaceOctober 4,, 2012Multi-Purposed PC to Phone Line Bridgewith Application SoftwarePPhhoonnee......771155..338866..88886611iinnffoo@@vviikkiinnggeelleeccttrroonniiccss..ccoommhhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..ccoomm• Compatible with Windows XP, Vista and Win7• USB to RS-232 cable pro …

Comments, Questions and Opinions: