Manualios.com

Cisco UBR10012 Quick Start Manual

Cisco UBR10012 Manual Online:

4.3, 2704 votes
Cisco UBR10012 User Manual
Cisco UBR10012 User Guide
Cisco UBR10012 Online Manual

Text of Cisco UBR10012 User Guide:

  • Cisco UBR10012, 36 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis Step 6 Secure the dual-hole lugs to the input studs on the DC terminal blocks by reinstalling the nuts. Note Secure the nuts using a 10 mm hex socket driver with an installation torque of 50-in lbs. Caution You must attach both pairs of DC-input cables to the DC terminal blocks on each PEM for proper functioning of the PEMs. Step 7 Repeat Step 3 to Step 6 to connect the second facility DC power source to the second PEM module. Step 8 Route the four pairs of DC-input cables from the DC power terminal blocks on both the PEMs down through the front

  • Cisco UBR10012, 16 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Overview Note The U-CHAS-COVER-PLUS= front cover must be used with the 3300 W DC PEM modules for proper routing of the DC cables through the chassis to the facility power source. Figure 8 shows the faceplate of this DC PEM module, which has: • Two DC power terminal blocks—These connect to the facility power source. • DC power enable switch—This powers on the DC PEM module. • Two Handles—These help during the rem

  • Cisco UBR10012, 15 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Overview Figure 7 DC Power Entry Module (UBR10-PWR-DC=) Three LEDs (POWER, MISWIRE, and FAULT) indicate the status of the DC PEM module. Note The DC PEMs receive –48 /–60 VDC power through two separate DC terminal blocks located beneath each PEM in the midplane of the Cisco uBR10012 chassis. For details on how to connect the DC cables, see “Connecting the DC Power Cables for the UBR10-PWR-DC= Module” section on page 34. DC Power Entry Module (UBR10-PWR-DC-PLUS=) This DC PEM module provides a power output of 3300 W with dua

  • Cisco UBR10012, 35 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis Step 6 Connect the second DC power source to the PEM 1 terminal (right terminal) as in Step 5. Step 7 If you are connecting visual or audio alarm indicators to your system, go to the “Connecting the Alarm Indicators” section on page 30. Step 8 If you are not connecting any alarm indicators, go to the “Installing the Modules” section on page 38. Connecting the DC Power Cables for the UBR10-PWR-DC-PLUS= Module Caution Do not use the DC power terminal connectors on the midplane of the chassis (see Figure 16) when you are using the UBR10-PWR-DC-PLUS= modu

  • Cisco UBR10012, 72 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Related Documentation This document is to be used in conjunction with the documents listed in the “Related Documentation” section. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Ci

  • 43 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis Figure 22 Routing of the AC cables From the Front Cover Installing the Fan Assembly Module The installation procedure is the same for both the fan assembly modules (UBR10-FAN-ASSY= and UBR10012-FAN-PLUS=). Figure 23 is a sample representation of the fan assembly module (UBR10012-FAN-A

  • Cisco UBR10012, 61 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Configuring the Cisco uBR10012 Router at Startup Tip Interfaces that are not okay (No) have an invalid configuration or are not configured. To set up an interface on the Cisco uBR10012 router: Step 1 Enter the interface for the Fast Ethernet interface to achieve network connectivity. Enter interface name used to connect to the management network from the above interface summary: FastEthernet0/0/0 Step 2 Accept the default value for the type of connector. RJ-45 is the only connector that can be used on the Cisco uBR10012 router Ethernet port. Configuring int

  • 7 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Overview Fan Assembly Module (UBR10-FAN-ASSY=) This fan assembly module has four internal fans that draw cooling air into the front of the chassis and direct it across the internal components. The air is exhausted through the openings in the rear of the chassis (see Figure 3). The fan assembly module wor

  • Cisco UBR10012, 24 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis Before You Begin • Make sure that you have an antistatic surface available for the components that you are removing from the chassis. • Make sure that you are wearing antistatic protection such as a wrist strap or heel strap and are properly grounded. Removing the Modules from the Chassis To remove the modules from the chassis: Step 1 Remove the front cover by pulling the cover towards you and carefully set it a

  • Cisco UBR10012, 62 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Configuring the Cisco uBR10012 Router at Startup Step 8 Enter global configuration mode after you complete the configuration, and enable ip routing by entering the ip routing command: router(config)# ip routing Basic Configuration in Global Configuration Mode The following command sequence allows you to perform a configuration similar to that generated by the setup command: Router> configure terminal Router(config)# hostname c10012 Router(config)# enable secret <my_router>

  • Cisco UBR10012, 47 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Connecting Cables Connecting Cables Tip To reduce the chance of interference, avoid crossing the power cables with any of the interface cables. Verify all cabling limitations (particularly distance) before powering on the system. Connect the Console Port and the Auxiliary Port The PRE module has two asynchronous serial (EIA/TIA-232) RJ-45 ports for connection to a console (an ASCII terminal or a PC running terminal emulation software) and modem for remote access. The cables a

  • Cisco UBR10012, 68 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Troubleshooting Fans do not function at startup. 1. Verify that the system has power. 2. Remove the fan assembly module, check the fan cables, and reinsert the module. Caution The total service window for removal and replacement of the fan tray is 3 minutes before possible system shutdown. Therefore, ensure that you complete the replacement procedure within this time limit to avoid system shutdown. Fan alarm LEDs illuminate. Note This applies to both UBR10-FAN-ASSY= and UBR10012-FAN-PLUS= modules. • If the Single Fan Failure LED is

  • Cisco UBR10012, 69 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Troubleshooting System overheats. Tip When the fans are operating, you can hear them. You can also feel air being drawn in at the bottom front and expelled at the top rear of the chassis. 1. Check for fan failure by checking the fan status LEDs and running the show environment command. Router# show environment Temperature normal: chassis inlet measured at 29C/84F Temperature normal: chassis core measured at 42C/107F Fan: OK Power Entry Module 0 type DC status: OK Power Entry Module 1 type DC status

  • Cisco UBR10012, Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide Part Number: OL-24972-01 Revised: April 15, 2010 Contents This document includes procedures for installing and removing the Cisco uBR10012 components that are shipped with the Cisco uBR10012 universal broadband router. This document also includes technical specifications and troubleshooting information. • Objective, page 2 • Audience, page 2

  • 28 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis Note Figure 11 shows the chassis flush-mounted at the rear. The procedure is identical for the front mounting method. Figure 11 Installing the Chassis in a Rack using the Rear Mounting Brackets Connecting the Chassis to Ground Connecting the Cisco uBR10012 router chassis to earth

  • Cisco UBR10012, 20 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Preparing the Site Power Guidelines Caution The Cisco uBR10012 router installation must comply with all applicable codes and is approved for use only with copper conductors. The ground bond fastening hardware should be of compatible material and preclude loosening, deterioration, and electrochemical corrosion of hardware and joined material. Attachment of the chassis ground to a central office or other interior ground system should be made with a minimum of a 6 AWG, copper gr

  • 22 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis Installing the Chassis Tip For easier installation, rest the chassis on an installation shelf while installing the chassis in a rack. Rack-Mounting Guidelines • Allow sufficient clearance around the rack for maintenance.You need 36 in. (91.44 cm) of clearance to remove and

  • Cisco UBR10012, 17 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Overview Five LEDs (V1 POWER, V2 POWER, POWER, MISWIRE, and FAULT) indicate the status of the DC PEM module. In addition, there is a PRODUCT ID LED/switch on the front panel of the DC PEM module. Table 5 lists the default activation status of the PRODUCT ID LED/switch when it is shipped. When you press the PRODUCT ID LED/switch it illuminates (green) and the Cisco IOS software identifies the PEM module as UBR10-PWR-DC-PLUS only if you are running a

  • Cisco UBR10012, 31 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis b. If you are wiring the router in series with other equipment for the alarm indicators, connect the other lead to the normally closed (NC) terminal. c. If you are wiring the router in parallel with other equipment for the alarm indicators, connect the other lead to the normally open (NO) terminal. Note Figure 13 shows the wiring configuration for NO alarm relays. For NC alarm relays, use the NC contacts. Step 4 Repeat Step 3 for the remaining alarm indicators Step 5 Se

  • Cisco UBR10012, 41 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Installing the Chassis To install the AC PEM module on the Cisco uBR10012 router: Step 1 Verify that the power switch on the AC PEM is in the Standby (0) position. Caution Do not connect power to the AC power sources or apply power to the chassis. This is done as part of the system startup after all connections are made. Step 2 Position the AC PEM in the power bay and slide it all the way in, and ensure that it makes a secure connection with the chassis backplane. Step 3 Tighten the captive screws to secure the AC PEM using a screwdriver. Note To tighten the captive screws on the AC PEM modul

  • Cisco UBR10012, 4 Cisco uBR10012 Series Universal Broadband Router–Quick Start Guide OL-24972-01 Overview Overview The Cisco uBR10012 universal broadband router is an aggregation platform that provides a high-end, high-performance, high-capacity Cable Modem Termination System (CMTS) solution. The system provides high-speed data, broadband entertainment, and IP telephony services over a coaxial cable connection to residential and commercial subscribers using cable modems or digital set-top boxes (STBs). The router enables high-speed data services to be packaged like they are in basic cable television services or vi

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Encore Networks VSR-1200 Installation and quick configuration manual encore-networks/vsr-1200-GX1.pdf 08 Jan 2023 26
2 LG LGUN150 Owner's manual lg/lgun150-BEP.pdf 24 Apr 2023 252
3 Simer 4850C Owner's manual simer/4850c-C2F.pdf 17 Jan 2024 24 2.18 Mb
4 Bose 301 Sonata Owner's manual bose/301-sonata-9Y8.pdf 07 Jan 2024 9 1.77 Mb
5 Toshiba RS-TX60 Viewer's manual toshiba/rs-tx60-9D7.pdf 12 Aug 2022 204 4.9 Mb
6 Lenovo THINKPAD X60S Troubleshooting manual lenovo/thinkpad-x60s-11I.pdf 25 Nov 2022 78

Similar Resources:

  • ORiNG

    IES-3160

    (2 pages)
    IES-3160P1P3P5P1P3P2P4P6P8P7P13P9P11P10P12P14P16P15PWRPWR 1PWR 2Quick Installation GuideVersion 2.1Quick Installation GuideIntroductionPRINTED ON RECYCLED PAPERQ I Gis managed Redundant Ring Ethernet switch with 16x10/100Base-IES-3160T(X) ports. With completely support of Ethernet Redundancy protocol, O-Ring (recovery time < 10ms over 250 units of conn …
  • Encore

    ENDSL-A2PLUS4R2

    (4 pages)
    ENDSL-A2+4R2 ADSL2+ Modem with 4 Port Ethernet Router ENDSL-A2+4R2 full rate ADSL2+ router is a full featured ADSL router that provides high-speed Internet access and Ethernet direct connections to individual PCs or local area network with 10/100 Base-T Ethernet. ENDSL-A2+4R2 use advanced ADSL chipset solution with complete set of industry standard feat …
  • Cisco

    ONS 15454 Series

    (166 pages)
    Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco ONS SONET TL1 Reference GuideCisco ONS 15454, ONS 15327, ONS 15310-CL, ONS 15600Product and Documentation Release 6.0 December 2009Text Part Number: 78-17045-01 …
  • Belkin

    Wireless G Router

    (2 pages)
    BESTGOODSpeed and PerformanceG+NBETTERGGGBASICHOMECONNECTIVITYThe G Wireless Router (F5D7234-4) is perfect for setting up a simple wireless network that has the speed for handling basic networking applications such as sharing a broadband Internet connection with multiple computers, surfing the Web, emailing, and instant messaging.The Router’s wireless rang …
  • Cisco

    700 series

    (36 pages)
    Cisco Headset 700 Series Administration GuideFirst Published: 2020-02-03Last Modified: 2020-09-23Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0883 …
  • NETGEAR

    FS605

    (2 pages)
    FS6055-port Fast Ethernet Switch10/100 MbpsHang on – your network will soar when it’s hooked up to NETGEAR’s FS605! Thispowerful plug-and-play switch connects at 10 or 100 Mbps and makes it easy to linkas many as five computers or peripherals to your Ethernet network. You’ll experiencemaximum performance for 10 or 100 Mbps devices with five ports tha …

Comments, Questions and Opinions: