Manualios.com

Cisco 15454-TCC - Network Processor Card Operation Manual

  • 15454-TCC - Network Processor Card Software
  • maLUnuKt7B/Do
  • Operation Manual
  • PDF / Adobe Acrobat Reader
  • 458

Cisco 15454-TCC - Network Processor Card Manual Online:

4.5, 1529 votes
Cisco 15454-TCC - Network Processor Card User Manual
Cisco 15454-TCC - Network Processor Card User Guide
Cisco 15454-TCC - Network Processor Card Online Manual

Text of Cisco 15454-TCC - Network Processor Card User Guide:

  • 3-15 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 3 Node Setup Setting Up ONS 15454 Timing • Timing Mode—Set to External if the ONS 15454 derives its timing from a BITS source wired to the backplane pins; set to Line if timing is derived from an OC-N card that is optically connected to the timing node. A third option, Mixed, allows you to set external a

  • Cisco 15454-TCC - Network Processor Card, C-7 Cisco ONS 15454 Installation and Operations Guide November 2001 Appendix C Acronyms IEEE Institute of Electrical and Electronics Engineers IETF Internet Engineering Task Force IP Internet Protocol IPPM Intermediate-Path Performance Monitoring I/O Input/Output ITU-T The International Telecommunication Union- Telecommunication Standards Sector J JRE Java Runtime Environment L LAN Local Area Network LCD Liquid Crystal Display LDCC Line Data Communications Channel LOP Loss of Pointer LOS Loss of Signal LOF Loss of Frame

  • Cisco 15454-TCC - Network Processor Card, 7-34 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 7 Card Provisioning Converting DS-1 and DS-3 Cards From 1:1 to 1:N Protection Note Deleting the 1:1 protection groups will not disrupt service. However, no protection bandwidth exists for the working circuits until the 1:N protection procedure is completed. Do not delay when completing this procedure. Step 10 If you are deleting more than one protection group, repeat Steps 7–9 for each group. Step 11 On the node view, right-click the DS3-12 card in Slot 3 or Slot 15 and choose Delete from the shortcut menu. Step 12

  • Cisco 15454-TCC - Network Processor Card, 6-11 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 6 Circuits and Tunnels Editing UPSR Circuits Figure 6-6 Editing UPSR selectors Procedure: Edit a UPSR Circuit Step 1 Log into the source or drop node of the UPSR circuit. Step 2 Click the Circuits tab. Step 3 Click the circuit you want to edit, then click Edit. Step 4 On the Edit Circuit window, click the UPSR tab. Step 5 Edit the UPSR selectors: • Reversion Time—Controls whether traffic reverts to the working path when conditions that diverted it to the pr

  • Cisco 15454-TCC - Network Processor Card, 2-4 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 2 Software Installation Running the CTC Setup Wizard Note On PCs, the mouse pointer scheme should be set to Windows Standard (Windows 95/98) or None (Windows NT or Windows 2000). To check the settings, choose Settings and then Control Panel from the Windows Start menu. Double-click the Mouse option. From the Pointers tab of the Mouse Properties dialog box, select the Windows Standard (or “none” for NT or Windows 2000) mouse scheme. Click OK. 2.3 Running the CTC Setup

  • Cisco 15454-TCC - Network Processor Card, B-5 Cisco ONS 15454 Installation and Operations Guide November 2001 Appendix B Regulatory and Compliance Requirements Installation Warnings DC Power Connection Warning Aviso Antes de executar um dos seguintes procedimentos, certifique-se que desligou a fonte de alimentação de energia do circuito de corrente contínua. Para se assegurar que toda a corrente foi DESLIGADA, localize o disjuntor no painel que serve o circuito de corrente contínua e coloque-o na posição OFF (Desligado), segurando nessa posição a manivela do interruptor do disjuntor com fita i

  • Cisco 15454-TCC - Network Processor Card, 7-20 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 7 Card Provisioning Provisioning Optical Cards Table 7-8 OC-N Card Threshold Settings on the Provisioning > Thresholds Tab Heading Description Options Port Port number • 1, 2, 3, or 4 (OC-3) • 1 (OC-12, OC-48, OC-192) CV Coding violations Numeric. Defaults (15 min/1 day): Line • 1312/13,120 (OC-3 Near & Far End) • 5315/53150 (OC-12 Near & Far End) • 21260/212600 (OC-48 Near & Far End) • 85040/850400 (OC-192 Near & Far End) Section • 10000/

  • Index IN-2 Cisco ONS 15454 Installation and Operations Guide November 2001 viewing 10-1 wires 1-33 alarm settings DS-1 card 7-6 DS-3 card 7-8 DS3E card 7-11 DS3XM-6 card 7-14 DS-N cards, general 7-3 EC1-12 card 7-17 Ethernet RMON thresholds 9-32 alarm suppression 10-14 alarm wires 1-33 AMP Champ EIA attaching a ferrite 1-61 attaching DS-1 AMP Champ cables 1-43 attach

  • Cisco 15454-TCC - Network Processor Card, B-6 Cisco ONS 15454 Installation and Operations Guide November 2001 Appendix B Regulatory and Compliance Requirements Installation Warnings Power Supply Disconnection Warning ¡Advertencia! Después de cablear la fuente de alimentación de corriente continua, retirar la cinta de la palanca del interruptor automático, y restablecer la alimentación cambiando la palanca a la posición de Encendido (ON). Varning! När du har kopplat ledningarna till strömförsörjningsenheten för inmatad likström tar du bort tejpen från överspänningsskyddets omkopplare och slår på strömmen igen genom att ställa överspänning

  • 11-4 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 11 SNMP SNMP Support Figure 11-4 Setting up SNMP Step 4 Type the IP address of your NMS in the IP Address field. Step 5 Type the SNMP community name in the Community Name field. For a description of SNMP community names, see the “SNMP Community Names” section on page 11-8. Note The comm

  • Cisco 15454-TCC - Network Processor Card, 4-13 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 4 IP Networking ONS 15454 IP Addressing Scenarios Figure 4-10 Enabling OSPF on the ONS 15454 Step 3 On the top left side, complete the following: • DCC OSPF Area ID—Enter the number that identifies the ONS 15454s as a unique OSPF area. The OSPF area number can be an integer between 0 and 4294967295, and it can take a form similar to an IP address. The number must be unique to the LAN OSPF area. • DCC Metric—This value is normally unchanged. It sets a “cost” for

  • Cisco 15454-TCC - Network Processor Card, 7-24 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 7 Card Provisioning Provisioning IPPM 7.4 Provisioning IPPM Intermediate-Path Performance Monitoring (IPPM) allows you to transparently monitor traffic originating on DS-1, DS-3, DS3E and DS3XM cards (Path Terminating Equipment) as it passes through EC-1, OC-3, OC-12, OC-48, and OC-192 cards (Line Terminating Equipment). To use IPPM, you create the STS circuit on the DS-N cards, then enable IPPM on the EC-1 or OC-N cards that carry the circuit. Note For Relea

  • Cisco 15454-TCC - Network Processor Card, 9-11 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 9 Ethernet Operation Ethernet Circuit Configurations For shared packet ring Ethernet, valid circuit sizes are STS-1, STS-3C and STS-6c. Step 14 Verify that the Bidirectional checkbox is checked. Note You must manually provision the circuits if you are building a shared packet ring configuration. Step 15 Click Next. The Circuit Creation (Circuit Source) dialog box opens. Step 16 From the Node menu, choose the circuit source. Any shared packet ring node can serve as the circuit source. Step 17 Choose Ethergroup from the Slot menu and click Next. The Circuit Creation

  • Cisco 15454-TCC - Network Processor Card, 3-9 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 3 Node Setup Creating Protection Groups Step 5 Click OK and click Apply. 3.5 Creating Protection Groups The ONS 15454 provides several card protection methods. When you set up protection for ONS 15454 cards, you must choose between maximum protection and maximum slot availability. The highest protection reduces the number of available card slots; the highest slot availability reduces the protection. Table 3-3 shows the protection types that can be set up for ONS 15454 cards. Procedure: Create Protection Groups Step 1 From the CTC node view, click the Provisioning > Protection tabs. Step 2 Unde

  • Cisco 15454-TCC - Network Processor Card, 5-15 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 5 SONET Topologies Bidirectional Line Switched Rings • East Port—Assign the east BLSR port for the node from the pull-down menu. (In Figure 5-11, this is Slot 12.) The east and west ports must match the fiber connections and DCC terminations set up in the “Install the BLSR Trunk Cards” procedure on page 5-11 and the “Create the BLSR DCC Terminations” procedure on page 5-13. For four-fiber BLSRs, complete the following: • Span Reversion—Set the amount of time that will pass before the traffic reverts to the original working path following a span reversion. The

  • Cisco 15454-TCC - Network Processor Card, 2-8 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 2 Software Installation Connecting PCs to the ONS 15454 Step 3 From the Internet Properties dialog box, click Connections > LAN Settings. Step 4 On the LAN Settings dialog box, either: • Deselect Use a proxy server to disable the service or • Leave Use a proxy server selected and click Advanced. On the Proxy Setting dialog box under Exceptions, enter the IP addresses of ONS 15454 nodes that you will access. Separate each address with a semicolon. You can insert an asterisk for the host number to include all the ONS 15454s on your network. Click OK to close each open dialog box. Procedure: D

  • Cisco 15454-TCC - Network Processor Card, 5-18 Cisco ONS 15454 Installation and Operations Guide 78-13453-01 Chapter 5 SONET Topologies Bidirectional Line Switched Rings 5.2.7 Adding and Removing BLSR Nodes This section explains how to add and remove BLSR nodes. To add or remove a node, you force a protection switch to route traffic away from the span where you will add or remove the node. Figure 5-15 shows a three-node BLSR before the new node is added. To add Node 3, you would: • Force a protection switch on the Node 1 (Slot 5, West) and Node 4 (Slot 12, East) span. The protection switch forces traffic away fro

  • Cisco 15454-TCC - Network Processor Card, 1-66 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 1 Hardware Installation ONS 15454 Assembly Specifications • Backplane access: LAN pin field 1.16.7 TL1 Craft Interface • Speed: 9600 bps • TCC+ access: RS-232 DB-9 type connector • Backplane access: CRAFT pin field 1.16.8 Modem Interface • Hardware flow control • TCC+: RS-232 DB-9 type connector 1.16.9 Alarm Interface • Visual: Critical, Major, Minor, Remote • Audible: Critical, Major, Minor, Remote • Alarm contacts: 0.045mm, -48V, 50 mA • Backplane access: Alarm pi

  • Cisco 15454-TCC - Network Processor Card, 6-5 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 6 Circuits and Tunnels Creating Circuits and VT Tunnels • Using Required Nodes/Spans—If selected, click Next to display the Circuit Route Constraints panel (Figure 6-3). On the circuit map, click a node or span and click Include (to include the node or span in the circuit) or Exclude (to exclude the node/span from the circuit). The order in which you select included nodes and spans sets the circuit sequence. Click spans twice to c

  • Cisco 15454-TCC - Network Processor Card, 2-14 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 2 Software Installation Working with the CTC Window Figure 2-5 CTC window elements in the node view (default login view) 2.6.1 Node View The CTC node view, shown in Figure 2-5, is the first view displayed after you log into an ONS 15454. The login node is the first node displayed, and it is the “home view” for the session. Node view allows you to view and manage one ONS 15454 node. The status area shows the node name, IP address, session boot date and time, number of critical (CR), major (MJ), and minor (MN) alarms, the name of the

  • Cisco 15454-TCC - Network Processor Card, 8-2 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 8 Performance Monitoring Using the Performance Monitoring Screen Figure 8-1 Viewing performance monitoring information 8.1.1 Viewing PMs Before you view PMs, be sure you have created the appropriate circuits and provisioned the card according to your specifications. For information about circuit creation and card provisioning, see the Cisco ONS 15454 Installation and Operations Guide. Procedure: View PMs Step 1 Open the electrical or optical card of choice. Double-click the card’s graphic in the main (node) view or right-click the card and select Open Card

  • 7-31 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 7 Card Provisioning Converting DS-1 and DS-3 Cards From 1:1 to 1:N Protection To create 1:1 protection for DS-1 and DS-3 cards, see the “Creating Protection Groups” section on page 3-9. Procedure: Convert DS1-14 Cards From 1:1 to 1:N Protection Note This procedure assumes DS1-14 cards are insta

  • 8-7 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 8 Performance Monitoring Using the Performance Monitoring Screen 8.1.5 Using the Baseline Button In Software R3.0 and higher, the Baseline button located on the far right of the screen clears the PM count displayed in the Current column, but does not clear the PM count on the card. When the current 15-mi

  • Cisco 15454-TCC - Network Processor Card, 5-45 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 5 SONET Topologies Linear ADM Configurations Figure 5-36 Converting a linear ADM to a UPSR Step 8 Physically reroute the other protect fiber to connect the two end nodes. In the Figure 5-36 example, the fiber between Node 1/Slot 5 and Node 2/Slot 5 is rerouted to connect Node 1/Slot 5 to Node 3/Slot 13. If you are leaving the OC-N cards in place, go to Step 13. If you are removing the cards, complete Steps 9 – 12. (In this example, cards in Node 2/Slots 5 and 13 are removed.) Step 9 In the middle nod

  • Cisco 15454-TCC - Network Processor Card, 1-64 Cisco ONS 15454 Installation and Operations Guide November 2001 Chapter 1 Hardware Installation ONS 15454 Assembly Specifications 1.16 ONS 15454 Assembly Specifications This section contains hardware and software specifications for the ONS 15454. 1.16.1 Bandwidth • Total bandwidth: 240 Gbps • Data plane bandwidth: 160 Gbps • SONET plane bandwidth: 80 Gbps 1.16.2 Slot Assignments • Total card slots: 17 • Multispeed slots (any traffic card except OC48 IR 1310, OC48 LR/ELR 1550, and OC192 LR 1550 cards): Slots 1 – 4, 14 – 17 • High-speed slots (any traffic card including OC48 IR 1310, OC48 LR/ELR 1550, and OC192 LR 1550 cards): Slot

Related Products and Documents (Software):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Lincoln Electric SVM 106-A Service manual lincoln-electric/svm-106-a-736.pdf 01 Jun 2023 121
2 Master HWI3000 Owner's operation and installation manual master/hwi3000-LED.pdf 09 Jul 2023 32
3 Hypercom T7 series Quick reference manual hypercom/t7-series-969.pdf 13 Mar 2023 6
4 National Instruments NI 9481 Operating instructions manual national-instruments/ni-9481-14Y.pdf 25 Mar 2024 23
5 Barco FLM R20+ Performer Operation & user’s manual barco/flm-r20-performer-111.pdf 22 Nov 2023 241 18.79 Mb
6 GDI SM2400 Operation & user’s manual gdi/sm2400-115.pdf 05 Oct 2022 34

Similar Resources:

  • Extreme Networks

    Ridgeline Guide

    (376 pages)
    Extreme Networks, Inc.3585 Monroe StreetSanta Clara, California 95051(888) 257-3000(408) 579-2800http://www.extremenetworks.com Ridgeline Concepts and Solutions GuideSoftware Version 3.0 Published: February 2011Part Number: 100396-00 Rev. 01 …
  • Sharp

    AR-C260P

    (41 pages)
    MODELAR-C260PDIGITAL FULL COLOUR PRINTERBe sure to become thoroughly familiar with this manual to gain the maximum benefit from the product.Before installing this product, be sure to read the installation requirements and cautions sections of the "Operation manual (for general information)".Be sure to keep all operation manuals handy for reference …
  • Nortel

    Meridian Meridian 1

    (612 pages)
    Option 11C Mini Planning and Installation GuideMeridian 1Option 11C MiniPlanning and Installation GuideDocument Number: 553-3021-209Document status: StandardDocument Release: 1.00Date: July 1999Year Publish FCC TM© 1999All rights reservedPrinted in CanadaInformation is subject to change without notice. Nortel Networks reserves the right to make changes in …
  • American Megatrends

    StorTrends 1100-P

    (31 pages)
    StorTrends® 1100 Set Up Guide MAN-1100-SG 06/30/06 Thank You Thank you for purchasing the StorTrends® 1100 storage appliance. Please take a few minutes to review this set up guide before beginning the installation process. If you require a further explanation of any item covered in this guide, please refer to the installation instructions on your CD …
  • Cisco

    Catalyst Series Switch 2940

    (12 pages)
    diskontcomputer.comFirma Matzner MichaelWiener Bundesstraße 384061 Pasching, Austria:: Seite 1 von 12 :: Datenblatt zum Produkt Cisco 8 10/100 Ethernet Ports mit DC# 42410 ::Fragen zu dem Produkt Cisco 8 10/100 Ethernet Ports? Kein Problem - wir helfen Ihnen per eMail ([email protected]) gerne weiter!Den aktuellen Preis und Lagerstand finden Sie onl …
  • Allied Telesis

    AR400 Series

    (110 pages)
    C613-16087-00 REV Cwww.alliedtelesis.comAlliedWare™ OSHow To |IntroductionAllied Telesis routers and managed layer 3 switches use IGMP—Internet Group Management Protocol—to track which multicast groups their clients belong to. This enables them to send the correct multimedia streams to the correct destination.This How To Note describes basic and advanc …

Comments, Questions and Opinions: