Cisco SFS 7000P Hardware Installation Manual

Text of Cisco SFS 7000P User Guide:

• Cisco SFS 7000P, ix Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Preface This preface describes who should read the Cisco SFS 7000P Hardware Installation Guide, how it is organized, and its document conventions. Audience Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install, replace, or service the equipment described in this publication.

• THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWA

• Cisco SFS 7000P, 3-6 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 3 Installing Field Replaceable Units Removing Power Supplies and Fan Units Step 6 Install the filler panel in place of the power or fan unit. or Install a new power supply or fan unit. If you are installing a new power supply or fan unit, see the “Installing a Power Supply or Fan Unit” section on page 3-2. Caution Never operate the device without a filler panel or unit it place because the device might overheat.

• 2-3 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 2 Installing the Cisco SFS 7000P Switch Preparing for Installation Preparing for Installation To safely and successfully prepare your environment for your Cisco SFS 7000P switch, you need to do the following: • Check the contents of the switch package. • Always use an approved ESD-preventative ankle

• Cisco SFS 7000P, CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, Giga

• Cisco SFS 7000P, CHAPTER 1-1 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 1 Product Overview The Cisco SFS 7000P switch provides data center managers with a high-performance, low-latency interconnect. • Switch Description, page 1-1. • System Features, page 1-3. • Administrative Features, page 1-5. Switch Description The Cisco SFS 7000P switch includes the features described in the following sections. See Figure 1-1 for an illustration of the switch. Figure 1-1 Cisco SFS 7000P Switch 154903 P o w e r S u p p ly 1 Power S

• Cisco SFS 7000P, Preface Obtaining Additional Publications and Information xxii Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Severity 1 (S1)—An existing network is down, or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation. Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operations are negatively affected by inadequate performa

• 2-11 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 2 Installing the Cisco SFS 7000P Switch Connecting Network Devices Installing the Switch with Two People The following method of installation requires two people to mount the switch into the rack. One person holds the switch while another person secures it to the rack. To install the switch

• Cisco SFS 7000P, 1-5 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 1 Product Overview Administrative Features Nonblocking Architecture The Cisco SFS 7000P switch provides nonblocking switch element architecture with full bisectional bandwidth for the switch chassis. Administrative Features The following sections describe the Cisco SFS 7000P administrative features. Real-Time Clock A real-time clock maintains correct time regardless of power conditions or connectivity. Latency The Cisco SFS 7000P switch has port to port latency of less than 200ns. Nonvolatile Memory The memory supports the followin

• Cisco SFS 7000P, 5-3 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 5 Hardware Diagnostic Tests Running Chassis Tests Step 2 Exit the test to view the progress of the test. The test takes approximately 5 to 8 minutes. SFS-7000P# show diagnostic card 1 ====================================================================== Diagnostic Tests For Cards ====================================================================== test : self-test slot-id : 1 iterations : 1 action : start result : success p

• Cisco SFS 7000P, Chapter 4 Managing the Cisco SFS 7000P Switch Managing the System with Element Manager 4-4 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 To view the Health Status window, perform the following steps: Step 1 Launch the Element Manager. Step 2 Select Health > Status. The Health Status window opens. (See Figure 4-3.) Figure 4-3 Health Status Window Using the Summary Tab Use the Summary tab (See Figure 4-3.) to view the status of the power, fans, and temperature sensors at once. The Summary tab has the following fields: • Power – A green check indicates that at least one power source is connected and functioning properly. – A red check indicates that th

• Cisco SFS 7000P, 4-7 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 4 Managing the Cisco SFS 7000P Switch Displaying System Information Displaying Power Supply Information To display information about the power supply, enter the show power-supply command. SFS-7000P# show power-supply =============================================================== Power-supply Information =============================================================== ps type oper-status utilization voltage --------------------------------------------------------------------

• Cisco SFS 7000P, A-1 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 APPENDIX A Specifications and Compliance Certifications This appendix describes the Cisco SFS 7000P switch specifications and compliance certifications. Chassis and Management Interface Table A-1 lists the general specifications for the chassis. Table A-1 Chassis and Management General Specifications Item Specification Operating temperature 0 to 45°C Nonoperating temperature -40 to 70°C Operating temperature gradient 20°C max. per 60 minutes Operating altitude 0 to 10,000 feet Nonoperating altitude 0 to 40,000 feet Operating humidity: 8 to 80% non-condensing Nonoperating humidity: 5 to 90% RH at 65�

• Chapter 5 Hardware Diagnostic Tests Running Chassis Tests 5-4 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 SFS-7000P> enable SFS-7000P# config SFS-7000P(config)# diag chassis test standard SFS-7000P(config-diag-chassis)# start SFS-7000P(config-diag-chassis)# Step 2 Display the status of the test by entering the show diag chassis command. SFS-7000P(config-diag-

• Cisco SFS 7000P, xi Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Preface Conventions Notes use the following conventions: Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the publication. Cautions use the following conventions: Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. screen font Terminal sessions and information the system displays are in screen font. boldface screen font Information you must enter is in boldface

• 3-2 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 3 Installing Field Replaceable Units Installing a Power Supply or Fan Unit Failed Power Supplies or Fan Units The status of power supplies and fan units can be checked using the CLI, the Chassis Manager, or the Element Manager. The available information includes the status, the vital product data (VPD)

• Cisco SFS 7000P, Chapter 2 Installing the Cisco SFS 7000P Switch Connecting Network Devices 2-12 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 • Switch card—4x 10 Gbps InfiniBand connectors Connecting InfiniBand Devices If you are using InfiniBand to connect to other workstations or switches, you will need standard 4x InfiniBand cables. InfiniBand cables can be used to connect any two InfiniBand devices, whether a switch or a host (see Figure 2-8). Figure 2-8 InfiniBand and Management Port Connections To c

• Cisco SFS 7000P, Chapter 3 Installing Field Replaceable Units Installing a Power Supply or Fan Unit 3-3 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Figure 3-1 Removing the Screws from the Power Supply Step 3 Remove the power supply or fan unit if one is in place (or “present”) by pulling on the black handle. 154010

• Cisco SFS 7000P, xiii Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Preface Conventions Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au num�

• xix Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Preface Cisco Product Security Overview From this site, you will find information about how to: • Report security vulnerabilities in Cisco products. • Obtain assistance with security incidents that involve Cisco products. • Register to receive security information from Cisco. A current list of secu

• Cisco SFS 7000P, Chapter 2 Installing the Cisco SFS 7000P Switch Rack-Mounting the Cisco SFS 7000P Switch 2-6 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Rack-Mounting the Switch To rack-mount the Cisco SFS 7000P switch in a rack, follow these steps: Step 1 Remove the switch, rack brackets, CD-ROM, parts bag, and documentation from the box. Step 2 Place the switch on a secure, clean surface. Step 3 Open the plastic bag containing mounting parts. Step 4 Check the slot in the rack for sufficient cleara

• Cisco SFS 7000P, Contents viii Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Self-Tests 5-2 Running Card Tests 5-2 Running a Card Self-Test 5-2 Running Chassis Tests 5-3 Running a Chassis Standard Test 5-3 Running Fan Tests 5-5 Running a Self-Test on a Fan 5-5 Running Power Supply Tests 5-7 Running a LED Test on the Power Supply 5-7 Running a Self-Test on a Power Supply 5-7 Displaying Hardware Errors 5-9 APPENDIX A Specifications and Compliance Certifications A-1 Chassis and Management Interface A-1 Electrical Specifications A-2 I NDEX

• Cisco SFS 7000P, CHAPTER 3-1 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 3 Installing Field Replaceable Units This chapter describes how to install the following field replaceable units (FRUs) in the Cisco SFS 7000P switch: • Power and Fan Modules, page 3-1 • Installing a Power Supply or Fan Unit, page 3-2 • Removing Power Supplies and Fan Units, page 3-5 Power and Fan Modules The Cisco SFS 7000P power supplies and fan units are hot-swappable. You can add a second module without powering off the

• Cisco SFS 7000P, 4-5 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Chapter 4 Managing the Cisco SFS 7000P Switch Managing the System with Element Manager – A red check indicates a high-temperature warning. Using the Power Supplies Tab Use the Power Supplies tab to view the operating status of the power supplies. (See Figure 4-4.) Figure 4-4 Health Status Power Supplies Window Using the Fans Tab Use the Fans tab to view the operating status of the fans. (See Figure 4-5.) Figure 4-5 Health Status Fans Window In the OperStatus field, a status of up indicates that the fan is operating correctly within the power or fan unit.

• Cisco SFS 7000P, Chapter 1 Product Overview System Features 1-4 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Hardware The Cisco SFS 7000P switch features hot-swappable redundant power and cooling. Ports If any single InfiniBand port fails, none of the other ports will have interrupted service. Fabric For redundancy, InfiniBand host channel adapters can be dual-connected to a redundant pair of Cisco SFS 7000P switches. In an InfiniBand fabric that includes more than one Cisco SFS 7000P switch, if the subnet manager on the Cisco SFS 7000P switch that is acting as the master fails, another subnet manager wi

• Cisco SFS 7000P, Chapter 2 Installing the Cisco SFS 7000P Switch Connecting Network Devices 2-14 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Note If your host does not provide an ample amount of space around an IB port, double-check that your IB cable connector engages fully. Move your connector back and forth to be sure that both sides of the connector have locked firmly into place. b. To remove a cable with a pinch connector, pinch both sides of the back of the connector and pull the connector away from the port (see Figure 2-11). Figure 2-11 Removing a Pinch Connector c. To remove a cable with a pull connector, grasp the connector with one h

• Cisco SFS 7000P, Chapter 1 Product Overview Switch Components 1-2 Cisco SFS 7000P Hardware Installation Guide OL-9167-01 Rev. A0 Connectors The Cisco SFS 7000P switch uses the following connectors: • Twenty-four 10-Gbps 4x copper InfiniBand ports • One 10/100 Ethernet RJ-45 management-Ethernet port for out-of-band management • One RJ-45 console port used to configure and monitor the Cisco SFS 7000P switch Switch Components The following sections describe the Cisco SFS 7000P switch components. LEDs The Cisco SFS 7000P switch features the following LEDs: • Chassis LEDs–Show overall sy

Related Products and Documents (Switch):

Comparable Devices:

Similar Resources:

• NETGEAR GS105E (3 pages) 24/7TECHNICAL SUPPORT*1-888-NETGEAR (638-4327)Email: [email protected]® Plus 5-port Gigabit Ethernet Switch Data SheetGS105E *1000MbpsMore Capabilities beyond Plug-and-play ConnectivityToday’s growing businesses are both placing more demands on and relying more on their network. Companies are putting more applications and demands on their Ethernet I …

• ABB SACE Emax 2 (18 pages) E1.2 - XT7Doc. N.° 1SDH000999R0528 - ECN000131197 - Rev. BMeasurement Enabler/Measurement Enabler with voltage socket - E1.2 - XT7SACE Emax 2 - Tmax XTInternal sockets IV with external Y connectionInternal sockets IVExternal sockets III/IVA1FInternal sockets IV Neutral on the rightOnly with code: 1SDA076244R1 - E1.2/XT7 voltage socket for neutral on the rig …

• Hewlett Packard Enterprise B Series (13 pages) HPE B-series 16Gb FCSwitches Quick StartInstructions© Copyright 2014, 2016 Hewlett Packard Enterprise Development LP*5900-4827*Part Number: 5900-4827Published: January 2016Edition: 4OverviewRead these instructions to set up and configure theHPE StoreFabric SN6500B 16Gb 96-port FCSwitch, HPE SN6000B 16Gb 48-port FC Switchand HPE SN3000B 16Gb 24-port FC Switc …

• Allen-Bradley D Series (20 pages) Installation InstructionsOriginal InstructionsFLEX I/O ControlNet Adapter ModulesCatalog Numbers 1794-ACN15, 1794-ACNR15, 1794-ACNR15XT, Series DTopic PageImportant User Information 2Environment and Enclosure 3North American Hazardous Location Approval 4European Hazardous Location Approval 5Electrical Safety Considerations 5Prevent Electrostatic Discharge 7S …

• Manhattan 161169 (2 pages) HI-SPEED USB POCKET HUB INSTRUCTIONS MODEL 161169 1 With your computer on, connect the hub’s built-in cable (A) to an available USB port. Your operating system will detect the hub and install any required driver(s) automatically. The LED (B) will light to indicate the hub is ready for use.2 If additional power is needed, use the included USB power …

• Voltex CUBO PSF12W (2 pages) PRODUCTFront Cover and Door AssemblyBase AssemblyModule Identification LabelSpare bracketsPole Filler Set Sticker Label SetPSF12W 1 1 1 1 1 1PSF18W 1 1 1 1 1 1PSF24W 1 1 2 1 2 1PSF36W 1 1 3 1 2 1TECHNICAL SPECIFICATION© Voltex Electrical 2020. All Rights Reserved.PRODUCT SUPPLIED NEUTRAL BARS SUPPLIED EARTH BARSPSF12W (2x(35mm²)+8x(16mm²)) + 2x[4x(16mm …

Comments, Questions and Opinions: