Manualios.com

Baja motorsports BA50 Owner's Manual

Baja motorsports BA50 Manual Online:

3.1, 2838 votes
Baja motorsports BA50 User Manual
Baja motorsports BA50 User Guide
Baja motorsports BA50 Online Manual

Text of Baja motorsports BA50 User Guide:

  • Baja motorsports BA50, 57 BRAKING The ATV has front brake drums one rear disc brake. WARNING Failing to inspect and maintain your ATV’s brake system properly could be hazardous. Improper maintenance of the brake increases your chance of having an accident. Be sure to inspect the brake before riding according to the INSPECTION BEFORE RIDING section. Always maintain your brakes according to the MAINTENANCE SCHEDULE. WARNING Operating the ATV in harsh conditions could be hazardous if you do not inspect brake wear often. Operating in mud, water, sand, or other extreme conditions can ca

  • Baja motorsports BA50, 39 TOOLS A tool kit is provided with your ATV. SPARK PLUG To determine if the standard spark plug is in good condition, check the color of the plug’s center electrode insulator after vehicle operation. A brown color indicates that the plug is correct. A white or dark insulator indicates that the engine may need adjustment, or another plug type may be needed. Consult your authorized dealer or BAJA INC. if your plug insulator is not a light brown color. CAUTION Failing to use the proper spark plug could damage your ATV. An improper spark plug may have an incorrect t or heat range f

  • Baja motorsports BA50, 66 SERIAL NUMBER LOCATION You need to know the frame and engine serial numbers to get title documents for your ATV. You also need these numbers to help your authorized service center or BAJA INC. order parts. The frame number is stamped on the front of the frame as shown in the photograph. The engine serial number is stamped on the left side of the crankcase. Write down the serial numbers here for your future reference Frame No./VIN#: Engine No.: Engine number Frame No./VIN# SERI

  • Baja motorsports BA50, 48 Oil Cap Oil Drain bolt INSPECTION AND MAINTENANCE ENGINE OIL The engine oil should be changed every 20 to 40 hours of operation. It should be changed more often in dirty and dusty areas. To change oil: 1. Park the vehicle on level ground. 2. Remove the oil cap. 3. Remove the oil drain bolt and drain the oil into a bucket. 4. Reinstall the oil drain bolt 5. Pour fresh oil of the specied type through the oil ll hole. NOTE: Approximately 900ml (1 Qt) of oil is requir

  • Baja motorsports BA50, 50 AIR FILTER The air cleaner element must be kept clean to provide good engine power. If you use your vehicle under normal, low-tension conditions, you should service the air cleaner at the intervals specied. If you ride in dusty, wet, or muddy conditions, you will need to inspect the air cleaner element much more frequently. Use the following procedures to remove the element and inspect it. WARNING Operating the engine without the air cleaner element in place could be hazardous. If the air cleaner element did not lter dirt

  • Baja motorsports BA50, 23 STARTING OFF When you are sure that the engine is warm, release front and rear brakes. WARNING The ATV may start moving as soon as you release the parking brake. Unexpected movement could cause you to lose control of the ATV. Make sure to apply the rear brake before you release the parking brake. WARNING Opening the throttle suddenly could be hazardous. The front wheels could leave off the ground and cause loss of control of the ATV. Always open the throttle gradually when you want to accelerate. Open throttle gradually to move forward. RIDING YOUR ATV WARNING Failure to use extra care w

  • Baja motorsports BA50, 64 WASHING YOUR ATV With some care, your ATV can be washed in a similar manner to washing an automobile. Note: Avoid spraying or allowing water to ow over the following places: · Ignition switch · Spark plug · Fuel tank cap · Carburetor · Air Filter Use a garden hose at low pressure to remove the majority of dirt or other debris. Hand wash your ATV with mild soap or detergent and water. Try to thoroughly remove all dirt and debris without excessive water pressure, even at remote areas such as between engine coolin

  • Baja motorsports BA50, 47 IDLE SPEED ADJUSTMENT To adjust the idle speed properly, you need a tachometer. If you do not have one, ask your authorized service center to perform this adjustment. To adjust the idle speed: 1. Start the engine and warm it up. 2. Turn the throttle stop screw in or out so that the engine idle speed is at 1400~1600r/min. FUEL HOSE WARNING Improper adjustment of the idle speed could be hazardous. An idle speed that is too high could cause the ATV to launch forward when you start the engine. This may cause an accident. Excessive engine wear may also result if idle speed is adjusted improperly or when the engine is not fully warmed up.

  • Baja motorsports BA50, 8 [Right] [Left] Front Tire Rear Tire Fuel valve Seat Gas cap Choke Mufer Front Shocks Rear Shock Safety Engine kill tether Oil Cap Drive chain ATV- BA50U Thumb Throttle

  • Baja motorsports BA50, “YOUR ATV CAN BE HAZARDOUS TO OPERATE. A collision or rollover can occur quickly, even during routine maneuvers such as turning and driving on hills or over obstacles, if you fail to take proper precautions. For your safety, understand and follow all the warnings contained in this owner’s manual and the labels on your vehicle. Failure to follow these warning can result in SEVER INJURY OR DEATH. Keep the owner’s manual with your vehicle at all times.” Failure to follow the age recommendations

  • Baja motorsports BA50, 35 ACCESSORY USE AND VEHICLE LOADING There are many types of accessories for sale. However, we cannot have direct control over their quality or suitability. We cannot test each accessory that is available. If you add the wrong accessories or misuse the vehicle with some accessories installed, it can make the ATV less safe to ride. Be cautious when choosing and installing accessories to your vehicle. Your retailer may be able to help you choose accessories and install them correctly. The guidelines below should help you to decide

  • Baja motorsports BA50, 37 WARNING Improper maintenance or failing to perform recommended maintenance could be hazardous. If you perform improper maintenance or do not maintain your ATV you may have an accident. Keep your ATV in good condition. Ask your authorized service center or a qualied mechanic to do the maintenance items marked with an asterisk (*). You may perform the unmarked maintenance items by referring to the instructions in this section if you have mechanical experience. If you are not sure how to do the maintenance ask your authorized service or call BAJA INC. INSPECTION AND MAIN

  • 21 RIDING YOUR ATV WARNING Operating this ATV at excessive speeds. Increases your chances of losing control of the ATV, which can result in an accident. Always go at a speed that is proper for the terrain, visibility and operating conditions, and your experience. WARNING Attempting wheelies, jumps, and other stunts. Increases the chance o

  • Baja motorsports BA50, 17 RIDING YOUR ATV WARNING Checking maintenance items when the engine is running could be hazardous. You could be severely injured if your hands or clothing get caught in moving ATV parts. Shut the engine off when performing maintenance checks, except checking the engine stop switch and throttle. BREAK-IN The rst month is the most important in the life of your vehicle. Proper operation during this break-in period will be helpful for assuring maximum life and performance of your new vehicle. The following guidelines explain proper break-in procedures. Maximum Throttle Opening Recommendation During the rst 10 hours of

  • Baja motorsports BA50, 31 RIDING THROUGH WATER You can ride the ATV through shallow water. Make sure it is not more than 10cm (4 inches) deep and is not moving fast. Choose a good place to cross before you ride through the water. Look for a spot where the banks are gently sloped on both sides and the bottom of the stream is hard. If you are unfamiliar with the area, park the ATV and inspect the stream rst to nd a suitable spot for crossing. When crossing, operate the ATV at a slow, steady speed. Be careful not to damage banks when crossing. WARNING Operating this ATV through deep or fast owing water could be hazardous. The ATV tires may oat losing traction and then los

  • 26 RIDING YOUR ATV OPERATION ON HILLS WARNING Operating on excessively steep hills. The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. Never operate the ATV on hills too steep for the ATV or for your abilities. Practice on smaller hills before attempting larger hills. CLIMBING A HILL WARNING Climbing

  • 38 It is very important to inspect and maintain your ATV regularly. Follow the guidelines in the chart. The intervals between periodic services in months are shown. At the end of each interval be sure to perform the maintenance listed. MAINTENANCE SCHEDULE Interval Initial 1 month/ 20 hrs Every 3 months/ 50 hrs Every 6 months/ 100 hrs Air Cleaner — C — †

  • Baja motorsports BA50, 40 NOTE: This ATV uses resistor-type spark plug to avoid jamming electronic parts. Improper spark plug selection may cause electronic interference with your ATVs ignition system, resulting in the vehicle performance problems. Use recommended spark plugs. To install a spark plug turn it in as far as possible with your ngers, then tighten it with a wrench. To maintain a proper functioning spark plug, keep the plug free of carbon. Remove carbon from the plug with a wire or pin, and adjust the gap to 0.6~0.7mm (.024”~ .027”) for good ignition. Use a thickness gauge to check the gap. CAUTION Improper installation of the spark plug could da

  • Baja motorsports BA50, 22 RIDING YOUR ATV WARNING Failure to inspect the ATV before operating. Failure to properly maintain the ATV. Increases the possibility of an accident or equipment damage. Always inspect your ATV each time you us it to make sure the ATV is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the owner’s manual. WARNING Removing hands from handlebars or feet from the footrests during operation. Removing even one hand or foot can reduce your ability to control the AT

  • 12 CONTROL FUNCTIONS RIGHT HANDLEBAR Throttle Lever Control the engine and ATV speed with the throttle lever. Operate this lever with your thumb. Push it forward to increase engine and ATV speed. Release it to decrease engine and ATV speed. Front brake lever Control the engine and ATV braking with the front brake lever. Squeeze lever toward g

  • 51 REMOVAL CLEANING AIR FILTER 2. Remove air lter Air lter 1. Remove side panel to access air lter Side panel Compressed air 1. Tap air lter gently against hard object to remove dirt and dust. 2. Blow air lter out gently with compressed air. 3. If air lter is damaged, replace. 4. Re-install lter making sure it is on securely, any air leaks around rubbe

  • Baja motorsports BA50, 18 STARTING THE ENGINE Before attempting to start the engine, make sure to follow these steps. 1. Turn the key switch to the ON position. 2. Set the engine stop switch to the “RUN“ position. 3. If engine is cold, turn choke lever 4. Apply the rear brake lever and make sure that the rear wheels are in locking condition. 5. Press the starter button “START” to start the engine. 6. After engine has warmed up, turn choke lever back. WARNING The ATV could start moving as soon as you start the engine. Unexpected movement could cause you to lose control of the ATV.

  • Baja motorsports BA50, 58 Rear hydraulic brake inspection 1. Inspect the rear disk brake caliper and brake uid reservoir for leakage. If brake uid leaks, the safety of riding could be affected. 2. Inspect the brake hose for cracks, and the joint for leakage. 3. Check the brake uid level in the brake uid reservoir, if level is at or below the LOWER mark, inspect brake pads for wear and hydraulic system for leaks. 4. To add brake uid, unscrew the 4 screws on top of the bake uid container. Add DOT3 or DOT4 brake uid. Do no

  • Baja motorsports BA50, 45 Battery Replacement: · Remove old battery. Mark which cable is connected to the positive terminal (+) and which cable is connected to the negative (-) terminal. · Clean cable connectors with wire brush or sandpaper to remove oxidation. · After charging, install new battery. Put dielectric grease on the battery terminals to avoid corrosion. Connect cables to the proper terminals. Positive cable to positive terminal Å and negative cable to negative terminal y. · Positive (+) cable i

  • Baja motorsports BA50, 52 DRIVE CHAIN The condition and adjustment of the drive chain should be checked before riding. Always follow the guidelines below for inspecting and servicing the chain. Inspecting the Drive Chain When inspecting the chain, look for the following: · Loose pins · Damaged rollers · Dry or rusted links · Kinked or binding links · Excessive wear If you nd anything wrong with the drive chain, solve the problem if you can. If necessary, consult your authorized service center. The drive chain is damaged means that the sprockets may also be damaged. Inspect the sprockets

  • Baja motorsports BA50, 11 LOCATION OF LABELS 4 4 - 3- Improper tire pressure or overloading can cause loss of control. Loss of control can result in SEVERE INJURY or DEATH. WARNING Cold tire pressure: Front: 4 ± 0.5 Psi (27.6 ± 3.5 Kpa) Rear : 4 ± 0.5 Psi (27.6 ± 3.5 Kpa) Maximum weight capacity; 100 lbs. (45 kg) NEVER ride as a passenger. Passengers can cause loss of control, resulting in SEVERE INJURY or DEATH. WARNING

  • Baja motorsports BA50, IV This manual should be considered as a permanent part of the vehicle and should remain with the vehicle when resold or otherwise transferred to a new user or operator. The manual contains important safety information and instructions which should be read carefully before operating the vehicle. ! WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. CALIFORNIA PROPOSITION 65 ! WARNING

Related Products and Documents (Toy):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Sharp DL-PAR38 Features & benefits sharp/dl-par38-DH6.pdf 22 Feb 2024 2 1.83 Mb
2 ViewSonic NeoSat SP2002 Operation & user’s manual viewsonic/neosat-sp2002-MI7.pdf 24 Jul 2022 6 0.75 Mb
3 Bosch NEB 36" Installation manual bosch/neb-36-7A1.pdf 21 Aug 2022 28 1.71 Mb
4 Zephyr ZVE-E30S Use & care and installation manual zephyr/zve-e30s-454.pdf 05 Oct 2023 19 0.72 Mb
5 Hi-Tech Trading HB-ZA310V Instruction manual hi-tech-trading/hb-za310v-VC6.pdf 09 Dec 2023 30
6 Beko FC140 Manual  beko/fc140-87F.pdf 02 Oct 2023 23 0.56 Mb

Similar Resources:

  • Rail King

    SANTA FE STEEL RAIL FREIGHT HAULER 2-6-0

    (36 pages)
    RKAIL INGBy MT H ElectricTrains®RAILKING 2-6-0 STEAM ENGINEOPERATING INSTRUCTIONSMaking the Most of Your InvestmentThank you for purchasing this RailKing Ready-to-Run Steam Engine Set.We at MTH Electric Trains take pride in manufacturing quality productslike your set, and we hope that you will enjoy it for a long time. Toensure the maximum durability and pl …
  • Faller

    222199

    (4 pages)
    Sa. Nr.224 942 0BOCKKRANGANTRY CRANEGRUEBOKKRANArt. Nr. 222199Vor Beginn des Bastelns sollten Sie sich mit den Spritzlingen und der Anleitung vertraut machen.Sollte es einmal vorkommen, dass ein Teil im Bausatz fehlt, kreuzen Sie bitte das fehlende Teil inder Anleitung an und schicken Sie diese bitte an Fa. Gebr. FALLER GmbH, Abt. Kundendienst,kundendienst@f …
  • Jabiru

    j160

    (6 pages)
    Jabiru Construction Manual Pre-Paint>Fuselage>Empennage>Fit horizontal stabiliser This document is controlled while it remains on the Jabiru server. Once this no longer applies it becomes uncontrolled. Issue: 0 1 2 Issued by: AS Page: 1 of 6 16 November 2021 Pre-Paint>Fuselage>Empennage>Fit horizontal stabiliser Issue Revisi …
  • LGB

    23851

    (14 pages)
    23851Brohltal-Mallet-DampflokDAS VORBILDUrsprünglich wurden diese Mal-let-Dampflokomotiven von Hen-schel & Sohn geliefert. Eine ähnli-che Lok baute Hanomag 1925ganz offensichtlich unter Verwen-dung der Henschel-Zeichnungenfür die meterspurige Bahn Zell-Todnau im Schwarzwald.Die Brohltalbahn erhielt 1929 eine gleichartige Maschine mit der Loknummer II …
  • Radica Games

    Barbie Gotta Groove 73020

    (2 pages)
    SOUND - Use this button to switch from medium, high, headset-medium or headset-high.RESET - Using a blunt object, press this button to reset the game. EAR SET - EAR SET - Use this piece to hear the music. MICROPHONE - Located on the ear set, the microphone allows you tosing along with the music.HOW TO WEAR BARBIE GOTTA GROOVE -GETTING STARTEDPress the ON/OF …
  • Stevens AeroModel

    RC-050

    (27 pages)
    RingRat (RC-050)Wing Span: 13.5 inches | Wing Area: 57 inches2 | Average Flying Weight: 1.3 ouncesVersion 1.0Build Instructions September 8, 2011!(c) 2011 Stevens AeroModel all rights reserved.! Page 1 …

Comments, Questions and Opinions: