Basler IP Fixed Dome Camera Operation & User’s Manual
|
Basler IP Fixed Dome Camera, Configuring the Camera 16 Basler IP Fixed Dome Camera Red Gain - If the White Balance Mode parameter (see above) is set to manual, then the Red Gain parameter can be used to adjust the intensity of the red in the captured images. Decrease the setting to make the images less red, and increase the setting to make the images more red. Note that if the White Balance Mode parameter is set to a value other than manual, the Red Gain parameter will be read only and will indicate the current red gain value as set by the automatic white balance control. Blue Gain - If the White Balance Mode parameter (see above) i
Configuring the Camera Basler IP Fixed Dome Camera 33 Stream AOI Editor - Whenever a stream tab is selected, a Stream AOI Editor screen will also be available as shown below. Rather than setting numbers in the boxes on the stream tab, you can use the editor to set the AOI size and position for the stream controlled by the currently selected tab. To set
Basler IP Fixed Dome Camera, Configuring the Camera 18 Basler IP Fixed Dome Camera 3.4 Streaming Parameters The parameters in the Streaming group are used to control the characteristics of the image area that will be captured by the camera’s sensor. They are also used to control the characteristics of the video streams that are output from the camera. The camera can produce up to three individually configured video streams. The streams are designated as stream 0, stream 1, and stream 2. Stream 0 is always enabled. Streams 1 and 2 can be either enabled or disabled. Each stream can be accessed by multiple network users. For mor
Basler IP Fixed Dome Camera, Configuring the Camera 30 Basler IP Fixed Dome Camera when you start an image stream because the decoder in the receiving device must wait longer for the initial I-frames. Live Buffer Size - Sets the size (in kilobytes) of the live buffer for the stream controlled by the currently selected tab. The live buffer is a ring buffer that stores the last N captured images for the stream (N depends on the size of the images being encoded and the size of the buffer). Alarm Buffer Size - Sets the size (in kilobytes) of the alarm buffer for the stream controlled by the currently selected tab. Normally, the alarm buffer is simply a ring buffer that stores the las
Basler IP Fixed Dome Camera, Day/Night Functionality Basler IP Fixed Dome Camera 77 Finally, the IR Filter current Level parameter lets you see the current darkness level as measured by the auto controls. Familiarizing yourself with how this value changes when the camera is viewing a dark scene and when it is viewing a bright scene will help you determine where the switch level should be set. You can use the Day/Night tab in the Image Controls parameters group (see page 16) to set the IR Filter Switch Level and IR Filter Wait Time parameters and to monitor the IR Filter Current Level parameter. The IR-Cut Filter Announce Feature The
Basler IP Fixed Dome Camera, Configuring the Camera 36 Basler IP Fixed Dome Camera 3.6 Alarm Handling Parameters The parameters in the Alarm Handling group are used to select the sources that can declare an alarm condition and to control the actions that will be taken when an alarm condition is declared. 3.6.1 Alarm Sources Section The alarm sources section of the alarm handling parameters group is used to select the sources that can declare an alarm condition. User Trigger Tab Source Enable - Check the Source Enable box on the User Trigger tab to enable the user trigger as a source for declaring an alarm condition. Digital In Tab Sour
Introduction 4 Basler IP Fixed Dome Camera Status Indicator LEDs - The green LED indicates the network connection speed. Off means the network speed is 10 MBits/s (or the network is not connected). On means the network speed is 100 MBits/s. The yellow LED indicates the level of network activity. Factory Reset Button - Resets the camera to factory defaults. See Section 4
Basler IP Fixed Dome Camera, Configuring the Camera Basler IP Fixed Dome Camera 37 3.6.2 Alarm Buffers Section Each video stream can have an alarm buffer. Normally, the alarm buffer on a stream is a simply a ring buffer that stores the last N captured images for the stream (N depends on the size of the images being encoded and the size of the buffer). If an alarm condition is declared, however, the alarm buffer will only continue to buffer post alarm images until the part of the buffer that is allocated for post alarm buffering is full. At that point, buffering will stop, and the pre and post alarm images held in the buffer will be retained until a new Alarm Buffer Arm command is issued. Note that you will only
Basler IP Fixed Dome Camera, Terminal Blocks 68 Basler IP Fixed Dome Camera The assignments for the wire fixing holes in the main terminal block are as shown below and explained in Table 3 on page 69. Fig. 6: Main Terminal Block The terminal block is a push-in type of connector. Either solid or stranded wires can be inserted into the wire fixing holes in the block. A wire can be removed from a fixing hole by pressing the release tab above the hole and pulling on the wire. Wires inserted into the fixing holes must have a minimum
Basler IP Fixed Dome Camera, Configuring the Camera 60 Basler IP Fixed Dome Camera 5. When the Download Complete screen appears, click the Close button. 6. Click the Close button in the Configuration Management dialog box. To upload a saved configuration file on your PC to the camera, follow the steps below. When you upload the file, the parameters in the uploaded file will overwrite the current parameter settings in the camera. 1. Click the Config Management button. 2. A Configuration Management dialog box will open as shown below. Click the Browse button in the dialog box. 3. A Choose Fi
Basler IP Fixed Dome Camera, Configuring the Camera Basler IP Fixed Dome Camera 43 Overlay Position - Sets the position of the text overlay bar. Top = Place the text overlay bar at the top of each streamed image. Bottom = Place the text bar at the bottom of each image. Click the Remove Text button to clear all of the text from the Overlay Text line. Click the + Date button to quickly enter the $date$ expression into the Overlay Text line. Click the + Time button to quickly enter the $timestamp$ expression into the Overlay Text line. Click the + Framecount button to quickly enter the $counter$ expression into
Configuring the Camera Basler IP Fixed Dome Camera 13 Exposure Offset - Is used to customize the operation of the camera’s automatic controls. Negative settings will bias the auto controls toward producing darker images. Positive settings will bias the auto controls toward producing lighter images. Backlight Compensation - Check the box to enable the camera’s backlight comp
Configuring the Camera 50 Basler IP Fixed Dome Camera 3.9.2 Logging Out and Logging In Once you have logged into the camera, a Logged in: indicator, a Change Password button, and a Logout button (shown circled in red below) will appear in the Basler tool bar. Notice that the Logged in: indicator displays the user name of the person who is currently logged into the camera (in this case, t
Basler IP Fixed Dome Camera, Configuring the Camera Basler IP Fixed Dome Camera 25 Click the Motion Mask button to open the Motion Mask Editor as shown below. The motion mask defines the area(s) of the image that will be used for the camera’s motion detection function (see Section 3.5 on page 34). Highlighted areas in the editor will be included in the motion detection mask and used for motion detection. Unhighlighted areas will not. To highlight an area within the editor, simply left click your mouse and drag the cursor over the editor screen. Note that you can set the mask so that it covers a single area as shown above or so that it covers several different are
Basler IP Fixed Dome Camera, Day/Night Functionality Basler IP Fixed Dome Camera 79 Controlling an External Device Based on the IR-Cut Filter Position As mentioned on page 77, the camera includes a capability called the IR-cut filter announce feature. When this feature is enabled, the camera will "announce" the current position of the IR-cut filter by setting the state of output pin 0. When the IR-cut filter is in the open position, output pin 0 will be set to active. And when the IR-cut filter is in the closed position, output pin 0 will be set to inactive. A com
Basler IP Fixed Dome Camera, Day/Night Functionality 78 Basler IP Fixed Dome Camera 6.2 IR-Cut Filter Control Options Controlling the IR-Cut Filter Position Via Input Pin 0 As mentioned in Section 6.1 on page 75, the IR-cut filter can be set for several different modes of operation. If you set the IR-cut filter mode to "Input Pin 0 Controlled" this will let you control the position of the IR-cut filter (open or closed), by inputting a signal into input pin 0 on the camera. When the input is active, the filter will be placed in the open position. And when the input is inactive, the filter will be placed in the
Basler IP Fixed Dome Camera, Configuring the Camera 20 Basler IP Fixed Dome Camera Frame Rate Mode - Sets the rate at which the camera’s sensor will capture frames (images). For example, selecting 15 FPS means that the camera’s imaging sensor will capture 15 frames per second. Note that on some camera models, typically those with large imaging sensors, the maximum rate at which the sensor can capture images (i.e., the frame rate) is limited. On these cameras, if you decrease the height of the sensor AOI, the rate at which the sensor can capture images will increase. So if you decrease the setting for the AOI Height parameter, you may see an increase in the maximum set
Basler IP Fixed Dome Camera, Configuring the Camera 14 Basler IP Fixed Dome Camera Gain Limit - When automatic gain control is enabled, (see Exposure Mode above) the Gain Limit parameter sets the maximum amount of gain that the automatic gain control can use. If the gain limit is set to "off", there will be no limit for the automatic gain control. Note that if the Anti-Flicker feature is enabled, the Gain Limit parameter setting must be 6dB or greater. Gain - When automatic gain control is disabled (see Exposure Mode above), the Gain parameter sets the gain for the captured images. Gain refers to the amount of amplification that is applied to the pixel values in each captured
Basler IP Fixed Dome Camera, Configuring the Camera Basler IP Fixed Dome Camera 45 3.7.2 RTSP Tab Enabled - Check the Enabled box to enable the Real Time Streaming Protocol (RTSP). RTSP is a control protocol that allows the camera to negotiate which transport protocol to use for the video streams. Typically, RTSP streaming should be enabled. RTSP Port - Sets the port that will be used by RTSP. The default port is 554. Multicast - Check the Multicast box to enable multicast streaming. Multicasting is a bandwidth conserving technology. It reduces bandwidth by allowing the camera to deliver a single video stream to multiple recipients on the network. Note that multicasting will only work for streams where th
DOWNLOAD |
Basler A504k Security Camera Operation & user’s manual
A504k |
Cisco 4300 Security Camera Operation & user’s manual
4300 |
Basler dome camera Security Camera Installation manual
dome camera |
Speco VL-67 Series Security Camera Specifications
VL-67 Series |
Basler A600f Security Camera Operation & user’s manual
A600f |
Grandstream Networks GXV3674_HD_VF Security Camera Operation & user’s manual
GXV3674_HD_VF |
Basler L304kc Security Camera Operation & user’s manual
L304kc |
Basler BIP2-DXXXXc-dn Security Camera Installation manual
BIP2-DXXXXc-dn |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Batribike | 20 | Operation & user’s manual | batribike/20-1A1.pdf | 07 Sep 2022 | 12 | |
2 | Canon | PIXMA PRO-1 Series | Setup manual | canon/pixma-pro-1-series-8J8.pdf | 30 Jan 2024 | 4 | 0.2 Mb |
3 | Wagan | Metro Personal | Operation & user’s manual | wagan/metro-personal-MZ2.pdf | 24 Oct 2022 | 5 | 0.73 Mb |
4 | Hyundai | DV5S747 | Instruction manual | hyundai/dv5s747-A56.pdf | 05 Jan 2023 | 80 | |
5 | ESI | Activ 05 | Operation & user’s manual | esi/activ-05-1H2.pdf | 29 Nov 2023 | 10 | 0.24 Mb |
6 | Sennheiser | Tourguide Charger L 2021-40 | Instruction manual | sennheiser/tourguide-charger-l-2021-40-3G2.pdf | 04 Dec 2022 | 18 | 1.06 Mb |
Conrad
쮕 Überwachungskamera mitSDHC-Slot Seite 3 - 18 Surveillance camera with SDHC Slot Page 19 - 34 Caméra de surveillance avec slot SDHC Page 35 - 50 Bewakingscamera met SDHC-slot Pagina 51 - 66Best.-Nr. / Item-No. / Node commande / Bestnr.: 75 17 71쮕BEDIENUNGSANLEITUNGOPERATING INSTRUCTIONSNOTICE D’EMLPOI GEBRUIKSAANWIJZINGVersion 12 …
75 17 71(68 pages) |
Vitek
blackVITEKMighty DomeColor Dome Camera Series• 480 and 550 TV Line versions • True Mechanical Day/Night function available• Flush or Surface Mount• UTP interfaceand Heater / Blower Options Available• Dual Voltage 12VDC & 24VAC• Infinity Ball Mount for Any Viewing Angle• Indoor and Vandal Proof IP 68 Rated Models Available• Lens options in …
Mighty DomeColor Dome Camera Series(28 pages) |
JVC
FIXED COLOR DOME CAMERATK-C553U(AC 24 V/DC 12 V)Cost-effective, Compact Programmable Color Dome Camera with Digital ZoomR䡲Variable Focal-Length Lens (f=2.6 to6 mm)䡲1/4-inch 380,000 Pixel CCD䡲High Sensitivity — 4 Lux (withcover), 1.5 Lux (without cover)䡲Digital 2X Zoom — Auto Pan, Tilt,Scroll and Preset Sequence (AutoPatrol) Mode 䡲6 Preset Posit …
TK-C553U - Fixed Color Dome Camera(4 pages) |
DW
STAR-LIGHT HDCOAX™ 1080p 2.1MP 20X Pan Tilt Zoom Camera DWC-PTZ20X User’s Manual Ver. 02/17 Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
…
DWC-PTZ20X(39 pages) |
Velleman
CAM 1/3" HR1/3" HRCAMÉRACÁMARA1/3" HOUSER MAGEBRUIKNOTICE MANUALBEDIENU MCOLD1R VARIFOCAL DR VARIFOCAL DA DÔME HR VAA DOMO DE ALOCHAUFLÖSENSANUAL KERSHANDLEI D’EMPLOI L DEL USUARIOUNGSANLEITU19 DOME CAMERADOMECAMERAARIFOCAL 1/3"LTA RESOLUCINDE VARIFOKASONY EFFIODING O NG A A " ÓN VARIFOCAALE DOME-KAMO DSP 246810 …
CAMCOLD19(16 pages) |
D-Link
This document will guide you through the basic installation process for your new D-Link Network Camera.DCS-7413Quick Installation GuideFull HD Day & Night Outdoor Network CameraQuick Installation Guide
…
DCS-7413(12 pages) |
Creative Webcam PC-CAM 300Webcam PDF Operation & user’s manual PC-CAM 300, 52 |
Rand McNally GPS intelliroute TND 510GPS #Z8JJCG intelliroute TND 510, 2 |
Seidel Engine UMS ST 7-70Engine Instruction manual (Seidel UMS ST 7-70) UMS ST 7-70, 17 |
Globe Wireless Microphone system SafeDial Wireless GL45-4GMicrophone system PDF Quick start manual SafeDial Wireless GL45-4G, 2 |
Honeywell Control Unit EC7823AHoneywell Control Unit Installation instructions manual (File: honeywell-ec7823a-installation-instructions-manual-8, 18.09.2023) EC7823A, 8 |
ProForm Other 660 Vx Treadmill660 Vx Treadmill Manual - O2N3B6 660 Vx Treadmill, 36 |
Shindaiwa Trimmer T350#GTL8N2: T350 Trimmer Owner's/operator's manual T350, 48 |
Toshiba Printer E-STUDIO 282Printer PDF Sales manual E-STUDIO 282, 48 |
Alto-Shaam Food Warmer EU2SYS-72/PFood Warmer Specification sheet (Alto-Shaam EU2SYS-72/P) EU2SYS-72/P, 2 |
Broan Ventilation Hood NuTone PM44Manual for Broan NuTone PM44 Ventilation Hood NuTone PM44, 4 |
Cooper Modem Elpro 450U-E#99PKN2: Elpro 450U-E Modem Operation & user’s manual Elpro 450U-E, 85 |
Gastroback Mixer Home CultureGastroback Product User Guide: Home Culture PDF Operating instructions manual - G868K3 Home Culture, 11 |