Manualios.com

Beam RST310 Installation And User Manual

Beam RST310 Manual Online:

3.7, 2810 votes
Beam RST310 User Manual
Beam RST310 User Guide
Beam RST310 Online Manual

Text of Beam RST310 User Guide:

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 33 Check the antenna. Is it properly mounted? Do you have a clear view of the sky? Check the signal strength. If the signal is weak, move the vehicle to a more open area. Check the Call Forwarding and Call Barring settings. Check the Ringer setting. If it is off, there is no audible ringer. Q You can’t make international calls. A Have you included the relevant codes? Press and hold the (+) key to display the international dialling prefix (+), and then enter the appropriate country code, fol

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 3 Package Contents The RST310 package contains:  1 x RST310 unit  1 x Universal plug-pack power adapter, 110-240V AC  1 x 9-pin-to-9-pin RS-232 cable (Male to Female)  1 x User manual (Printed)  1 x Ram Mount Bracket  1 x 9505A handset connector cable  2 x Mounting Brackets  1 x Mounting Screws (packet)  1 x CD including; AT command set, installation guide, user guide and intelligent handset manual Optional Accessories Alert / Monitoring Interface Battery Backup

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 27 Remote Configuration The Supervisor Menu items are available for remote configuration via a combination of the Iridium Short Burst Data and or SMS services. Refer to your Service Provider on how to register for this service. To configure your RST remotely you will need to know its Phone Number, Supervisor PIN and International Mobile Equipment Identifier (IMEI) number. Multiple configuration commands can be sent in one SMS and the Supervisor PIN is only required once at the start. Once the PIN has been entered the top of hierarchy for each subsequent command in the message is the Supervisor menu. Digits can be

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 24 Connecting your RST310 with a PABX The RST310 RJ11 port presents as an FXS line, that is it looks like an exchange or central office line to a standard DTMF telephone attached to the RJ11 analog port. If instead of a standard telephone, a PABX is connected, then the RST310 is performing the role of the network trunk as shown below: Call Progress FXS Initiate incoming call Sends ring to PBX Call Progress state Indicated by configured service tones Detects outgoing call from PBX Detects off-hook from PBX Progress state Sends dial tone to PBX Signalling in-call DTMF Detect disco

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 14 Option B: Using the brackets supplied the Ram-mount handset holder can be firmly attached to the terminal as pictured below, follow the above instructions for mounting the terminal, however using the longer mounting screws supplied affix the additional ram- mount holding bracket to the side of the unit. Connect the right angled bracket to the main terminal as pictured below Ram Mount Connector Bracket Attach as shown Attach Ram-Mount base

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 31 RS232 Port Signal Support and Handshaking On the data logging port, DCD and DSR output signals are related to DTR input and CTS is tied to RTS as shown. The Data port supports full software XON/XOFF handshaking on data (AT commands bypass this as standard for Hayes modems) or full hardware handshaking on RTS/CTS with DCD carrier indication. The Log port has no software handshaking support and hardware handshaking is loop-back only since the command set requires a minimal buffer. RS232 Port LBT Data Port Data Log

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 26 Using an SMS-POTS telephone connected to an RST310 enables the handset to be run long distances from the RST310 over whilst still supporting SMS. Typically the Intelligent type handsets are limited to less than 10m/30’ whereas the SMS-POTS being on the RJ11 line will support 100s metres / 1000s feet. Connecting an configuring an SMS-POTS telephone An SMS-POTS telephone is easily connected to the RST310 terminal via the RJ11 connection (as mentioned abo

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 15 2. Connecting the Power Cable 1. Make sure the AC power switch supplying the RST310 power pack is off. 2. Plug in the power cable into the power jack located on the rear panel of the RST310. 3. Secure the cable by tightening the plug retainer. 3. Connecting 9505A Handset Cable 1. Connect the supplied connector cable to the 25pin socket on the rear of the RST310 main terminal. 2. Ensure that the cable can reach to be easily connected to the base of the handset as req

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 25 Configuring the RJ11 port parameters The ability to configure the RJ11 port parameters is one of the major features of the RST310. Port parameters can be configured using the BEAM Management System (BMS). The BMS allows the configuration of: • Dialled number processing (to support crew calling and specialised applications) • Line settings such as dial tone frequency and sound (in order to make the RST310 sound like any other phone in the network) • Gain settings (to allow optimisation for short and long copper tails up to 500m) • Impedance (to accommodate a large range of terminals equipment including PBXs) This

  • RST310 INSTALLATION & USER MANUAL 21 7. Connecting to the Log Port 1. Connect the laptop to the Log port. The Log port should only be used for configuration and control of the terminal equipment. The LOG port can not be used for Communications or Data Services . 2. The LOG Port can also be used when using a Beam Alert/Monitoring Device, refer to the instruction provi

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 22 Making a phone call Logging on to Iridium Network With the power turned on, the RST310 will attempt to register with the Iridium network. The Signal LED uses colours to indicate how strong the Iridium signal is at your location. Signal LED colour Signal strength definition Green Strong Orange Acceptable Red No signal, no calls possible refer to “Troubleshooting” section In most cases the indicator will show green after a short period of approximately 15 seconds – orange indicates an acceptable but marginal signal strength. If the indicator remains red, there is a

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 18 5.1 Decoded antenna orientation: To operate this phone with the antenna in the DECODED orientation (above) for enhanced user convenience, the95095A handset settings need changing. 1. With the phone turned ON enter the following code: * # 92 # 2. Power cycle the handset (turn handset OFF then ON to save settings). Note: Be careful when removing or installing the antenna or adaptor that the handset power is turned OFF. The handset should not be turned on until after the connector cable is correctly attached (as described above).

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 28 Accessories & Options BEAM RST970: Intelligent Handset The RST310 is capable of supporting voice services on the Iridium network through the use of an (optional) Intelligent handset. This Intelligent Handset enables you to access Voice and SMS services over the Iridium network in conjunction with the RST310. Connecting an Intelligent Handset The Intelligent handset is easily connected to the RJ45 socket located on the RST310 Voice Data module. The unit should be powere

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 9 RST310 Overview The Front Panel Status LEDs 1. Power 2. Voicemail waiting* 3. SMS waiting 4. Call status 5. Signal strength * Subject to network availability The Rear Panel Rear Connectors 6. 9505A Connection 7. 11-32V DC Power Input 8. RJ11 / POTS Output (Accessory / External ringer) 9. RJ11 / POTS Output (Main) 10. Intelligent Handset or In-Vehicle Accessory connection 11. Comm Port for data connectivity 12. Log Port : Beam Terminal Configuration 13. Reset Button: Power Cycles unit 6 7 8 9 10 11 12 13 12345

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 17 Removing the Antenna from the 9505A handset 1. Ensure the antenna is facing down and completely retracted 2. Holding the 9505A handheld firmly press down on antenna release button 3. Whilst holding down the release button firmly, remove the antenna from the connection gently. Connecting the antenna adaptor to your handset Reverse the antenna removal sequence to reconnect the antenna adaptor. Ensure that the antenna adaptor “clicks” into place in either of the 45° angles: STANDARD ORIENTATION DECODED ORIENTATION (Needs programming - see below) Ensu

  • RST310 INSTALLATION & USER MANUAL 20 When the vehicle ignition is turned off, the handset will turn off after a delay as follows:  The unit will prepare to turn-off phone after the first 5 seconds.  The vehicle ignition can be returned to ACC / ON position during this time, and the phone will remain on without phone power dropout.  This is use

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 23 Accessing Vmail and SMS on your RST310 Voicemail When a Voicemail message has been received by the RST310 the Vmail LED will flash. The LED will stop flashing when the message has been cleared when the user connects to the Voicemail retrieval number programmed in the RST310. SMS - Short Message Service When an SMS has been sent to the RST310, the SMS LED will flash. This means that the SMS is ready to be read. The indicator is cleared when the SMS has been read and cleared from the RST310 memory. Note: Refer to Connecting a PC for d

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 6 Safety Information IMPORTANT! Please read the following information carefully before installing and using this BEAM equipment. Failing to follow instructions may compromise the safety of the product and may result in personal injury and/or equipment damage. Please consult your supplier if you have any further questions. Your RST310 is a low power radio transmitter and receiver. When it is ON, it receives and sends out radio frequency (RF) signals. The design of your RST310 system complies with international safety standards. Refer to the appropriate section of the RST310 User Manual for additional relevant safety inf

  • RST310 INSTALLATION & USER MANUAL 16 4. Connecting an RJ11 telephone handset 1. Plug the telephone, answering machine or corded/cordless phone into the Line and or Accessory Socket RJ11. It is important to note that Facsimile Messaging is not supported on the Iridium Network via a standard RJ11 connection. 2. Plug the optional Intelligent Handset int

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 11 Getting Started What is a SIM Card? A SIM Card is a Subscriber Identity Module (computer chip) that contains identity information for accessing the Iridium network. It functions as the digital memory of the RST310 and also stores your personal information, including received SMS messages. SIM Card Protection Handle the SIM card with care, avoid exposing the card to static electricity, water or dirt. Scratching or bending the SIM card will damage the card or its metal contacts. I

  • Beam RST310, RST310 INSTALLATION & USER MANUAL 29 Specification Summary Electrical Power 11-32V DC 2.5A Plug-pack (if provided) 90-250VAC 50/60Hz input Power Consumption (Average Current) Input Voltage 12V 24V Standby Mode 0.35A 0.16A Talk/Transmit Mode 0.52A 0.26A Subscriber Line Interface Ring Equivalence Number 3 REN Impedance 600 Ω or TN12 2-wire interface Open circuit voltage -48V DC+- 5% Ring Voltage > 56V RMS EMC Compliance C-Tick and A-Tick, CE mark, Environmental Operating Temperature Range -15°C to +55°C ambient Operating Humidi

  • RST310 INSTALLATION & USER MANUAL 4 User information " Please record your serial number here for future reference: Model: RST310 Serial no.: # This number can be copied from the white shipping label on the RST310 box Eg. 100A2800 The following PIN codes may be required to use your RST310, please complete these

Related Products and Documents (Docking Station):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 HP Pavilion t400 - Desktop PC Product specifications hp/pavilion-t400-desktop-pc-OXV.pdf 15 Jul 2023 2 0.07 Mb
2 Silvercrest NM1005 User manual and service information silvercrest/nm1005-R6E.pdf 25 Jul 2022 55 1.67 Mb
3 Delta 36-220 Instruction manual delta/36-220-TUH.pdf 01 Mar 2024 23 1.76 Mb
4 Lincoln Electric RANGER 3 PHASE 11079 Operator's manual lincoln-electric/ranger-3-phase-11079-YU6.pdf 17 Apr 2023 36
5 Beko MWB2511 Installation manual beko/mwb2511-85Z.pdf 07 Aug 2023 2 0.1 Mb
6 AMD ATI Radeon HD 5450 Operation & user’s manual amd/ati-radeon-hd-5450-J3J.pdf 22 Apr 2023 26 0.95 Mb

Similar Resources:

  • Jensen

    JiMS-215i

    (22 pages)
    ® Docking Digital CD Clock Radio For iPod® and iPhone® USER MANUAL JiMS-215i (iPod/iPhone Not Included) PLEASE READ THIS OPERATING MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE. …
  • Bose

    Wave SoundTouch

    (2 pages)
    1 3ENGLISHLatch Pasador Loquet Tab Lengüeta Poussoir2READ THIS FIRST Read the Important Safety Instructions on the other side. To set up the SoundTouch™ controller, you need: • SoundTouch™ app installed on your computer.• SoundTouch™ system connected to your home network.Note: The controller operates the SoundTouch™ system that you select …
  • Targus

    DOCK570EUZ

    (60 pages)
    FOUR HEAD 4K DOCKWITH 100W POWER DELIVERYUser Guide3 YEAR LIMITED WARRANTY: We pride ourselves on the quality of our products. For complete warranty details and a list of our worldwide o󰘲ces, please visit www.targus.com Features and specifications are subject to change without notice. All trademarks and registered trademarks are the property of th …
  • Philips

    AJ300D/12

    (2 pages)
    AJ300DDocking Entertainment SystemQUICK STARTMISE EN SERVICE RAPIDEINICIO RÁPIDOSCHNELLSTARTSNELSTARTAVVIVO RAPIDOThanks for buying Philips AJ300D Docking Entertainment System.Our Quick Start guides you through just some of the features on the set.Please read our instruction booklet to really rise & shine!DC 18VAB/CDCCEENGLISHStep A• Connect the sup …
  • Vantec

    DSH-M100U3

    (14 pages)
    USB 3.0 Universal Mini Docking Station Adapter User Manual DSH-M100U3 Ver. 1.00 All brand names and trademarks are properties of their respective owners. www.vantecusa.com Copyright © 2015 Vantec Thermal Technologies. All Rights Reserved …
  • Philips

    DC320/98

    (2 pages)
    1Quick start guideENWhat’s in the box2ConnectSetupEnjoy 3© 2010 Koninklijke Philips Electronics N.V.All rights reserved.Specications are subject to change without notice.Trademarks are the property of Koninklijke PhilipsElectronics N.V. or their respective owners.Printed in China DC320_98_QSG_V1.0Quick Start GuideUser ManualUser Manual Quick Start Guid …

Comments, Questions and Opinions: