Manualios.com

Boca Systems Adjustable MC Ghost Operation & User’s Manual

  • Adjustable MC Ghost Printer
  • maciWX5kJ4y26
  • Operation & User’s Manual
  • PDF / Adobe Acrobat Reader
  • 27

Boca Systems Adjustable MC Ghost Manual Online:

3.1, 768 votes
Boca Systems Adjustable MC Ghost User Manual
Boca Systems Adjustable MC Ghost User Guide
Boca Systems Adjustable MC Ghost Online Manual

Text of Boca Systems Adjustable MC Ghost User Guide:

  • Boca Systems Adjustable MC Ghost, PAPER MODE? Is generally used only for test purposes. It may also be used on roll stock with no black marks on the ticket. Your choices are YES (Enabled) or NO (Disabled). NO is factory default. INC BPP CUT COUNT? Enables the operator to move Boarding Pass tear position to the left (towards the ticket exit area). Cut counts are increments of .005” for 200dpi. The count value is changed by depressing CHOICES. 16 is factory default. DEC BPP COUNT? Enables the operator to move the Boarding Pass tear position to the right (towards the ticket entrance area). Cut coun

  • Table of Figures and Appendices Page Figure 1 Packaging 2 Figure 2 Micro Ghost Ticket Printer 3 Figure 3 Side view with door open 3 Figure 4 Rear view 4 Figure 5 Side view with electronics exposed 4 Figure 6 Ticket loading 5 Figure 7 Slider Adjustment 6 Figure 8 Optical Devices 10 Figure 9 Print head removal 12 Appendix A Operator Menu options through control panel

  • Boca Systems Adjustable MC Ghost, Figure 4 - Micro Ghost - rear view Figure 5 - Micro Ghost - top view with electronics exposed 4 Roll Stock Holder Main Logic Board AC connector On/Off switch Ticket Entrance Slot Interface connector, Output to another printer (25 pin male) Interface connector, Input from Host to another printer (25 pin female)

  • Boca Systems Adjustable MC Ghost, 6.0 Standard Interface Pinouts 6.1 Serial Pinouts RS232 (Standard) Pin Function 2 Printer Transmit 3 Printer Receive 7 Ground 5,20 DTR (Printer Ready) 4,22 RTS (+5Vdc) 25 pin to 9 pin Adapter 25 Pin Female 9 Pin Male 23 32 47 58 66 75 20 4 7 HOST COMPUTER OR TERMINAL PRINTER # 1 PRINTER # 2 Cable #1 9M 25M Cable #2 9F 25M25F 25M 25F 25F-9M Pin Adapter Wiring for Cable #1 9 Pin Male 25 Pin Male 22 33 57 620 84 Wiring for Cable #1 9 Pin Female 25 Pin Male 22 33 57 620

  • Boca Systems Adjustable MC Ghost, 8.1.7 Rubber Drive Roller (Platen) The rubber drive roller should be cleaned once a year to prevent paper dust from building up on the roller. Clean drive roller with a paper towel and alcohol. 1. Lift up the cam lock assembly (located above the head mounting block) to remove pressure from the thermal head. (see figure 9a) 2. Lift up the head mounting block/thermal head to remove it. (see figure 9b) 3. Clean the full legth of the Platen. 4. Install the head by reversing steps 1 and 2. Printer is now ready for normal ope

  • Boca Systems Adjustable MC Ghost, WARRANTY INFORMATION PRINTERS - BOCA warrants each printer to be free of defects for a period of one year from the date of shipment when subject to normal use and service. This warranty covers all parts and labor except for the print head which is warranted for 90 days. All warranty labor is to be performed at the BOCA facility. Equipment damaged by misuse or negligence including damage to print heads caused by defective ticket stock is excluded from this warranty. Any defective equipment meeting these conditions should be returned to BOCA for repair (freight prepaid) in its original box and packing material. A short note describing the failure should

  • 9.0 Spare Parts List DESCRIPTION PART NUMBER AC Switch and power filter P31-1000 Belt, Timing 100T (200 dpi) P50-1011 Control Panel Assembly, FGL41 421671 Display Panel, FGL 41 (LCD) P38-1003 Fuse 1A SB (220v operation) P29-1007 Interface Board (25 pin Female) 422190-6 SER Interface Board (25 pin Male) 422190-4 Logic Board FGL 41 Optical Detector, Reflective 422264 Optical

  • Boca Systems Adjustable MC Ghost, Appendix A - Operator Menu Options This printer allows the user to adjust various printer options through the control panel. To access and use the OPERATOR MENU, follow these steps: 1. Ticket stock should be loaded into the printer. 2. Press both MENU and TEST switches simultaneously for about three seconds. The LCD window displays OPERATOR MENU! . 3. To scroll through the menu topic, use MENU stopping on the topic you wish to change. 4. Press CHOICES to scroll through choices in the selected topic. NOTE: The printer displays a blinking cursor for the values presently stored in the printer. 5. Once you have found the new value you want, press

  • Boca Systems Adjustable MC Ghost, FCC NOTICE NOTE: The equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of t

  • 3.0 A Tour of Your Printer Figure 2 - Micro Ghost ticket printer Figure 3 - Micro Ghost ticket printer 3 ticket output slot control panel Adjustment Knob Timing belt Drive Pulleys Stepper Motor Transformer LCD

  • Boca Systems Adjustable MC Ghost, 5.0 Configuration The Adjustable MC Ghost is factory configured for a variety of customer requirements. 1. The printer has a resolution of 200dpi. 2. The printer has an adjustable paper path (see figure 7) 3. The printer has a serial interface for input from the host or another printer (see figure 4), and a serial interface for output to another printer. See pinouts in section 6.0. A number of other features including baud rate, cut count and print speed are factory set but can be modified (Operat

  • Boca Systems Adjustable MC Ghost, Table of Contents Page 1.0 Introduction 1 2.0 Unpacking the Printer 2 3.0 A tour of your printer 3-4 4.0 Installation 5 5.0 Configuration 6 6.0 Standard Interface Pinouts 7 7.0 Thermal Paper - Theory and Specification 8 8.0 Maintenance and Adjustments 9-13 9.0 Spare Parts List 14 10.Troubleshooting Guide 15-16

  • Boca Systems Adjustable MC Ghost, 1.0 Introduction The BOCA Adjustable MC Ghost is a direct thermal ticket printer especially designed for airline boarding pass and bagtag applications. The printer will automatically determine if a boarding pass or tag is loaded. Two printers can be daisy chained together in order to print both passes and bag tags from a single host computer. This manual will provide the user with general information regarding printer set-up, configuration and troubleshooting. Please consult the programming guide for additional technical details. 1

  • Boca Systems Adjustable MC Ghost, 8.0 Maintenance and Adjustments Your ticket printer is solidly constructed and has been designed for high volume use. It requires minimal care to provide maximum service. This section provides an overview of printer maintenance, including parts alignments, adjustment and replacement. For discussion purposes, the printer consists of two major modules or assemblies: • Paper guide and print head assembly • Logic board assembly As a safety precaution, all service to the printer should be done with power off and the AC cord unplugged from the printer. 8.1 Paper G

  • Boca Systems Adjustable MC Ghost, 2.0 Unpacking the Printer The printer is shipped in a ruggedized container. Please save packing material for future use. Remove the printer (see figure 1) and accessories from the box and inspect for obvious damage. If damage is noticed please report it immediately to BOCA. Tel: (561) 998-9600 Fax: (561) 998-9609 The following items should be in the box: a) Ticket Printer b) Chinese AC power cord c) Programming guide (on disk) d) This manual (on disk) e) Roller Stock Holder f) 9 pin to 25 pin adapter 2 Figure 1 - Packaging

  • Boca Systems Adjustable MC Ghost, 4.0 Installation The Adjustable MC Ghost ticket printer is designed to be mounted on a desktop or on a shelf. Prior to the site preparation and installation, the printer should be posered up and run in the self test mode. Lay the printer flat on a counter as shown in figure 3. Verify that line voltage is the same as the line voltage specified on the serial tag. Attach the AC cord and interface connector into the proper connectors as shown in figure 4. Turn power on. The LCD will display PAPER OUT. If required adjust t

  • Boca Systems Adjustable MC Ghost, BOCA SYSTEMS, INC. © 1999 Boca Systems, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of BOCA. Every effort has been made to ensure that the information in this manual is accurate. BOCA is not responsible for printing or clerical errors and reserves the right to change specifications without notice.

  • 10.0 Troubleshooting Guide This is a simplified troubleshooting guide listing some of the typical problems. It is not intended to provide technical details or repair methods, but can serve as a guide to fault isolation in the field. If you need additional help, please contact BOCA at Tel: (561) 998-9600 Fax: (561) 998-9609 1. NO OPERATION, POWER INDICATOR IS

  • Boca Systems Adjustable MC Ghost, 5. ERRACTIC PRINT POSITION a. See # 4 6. POOR PRINT OUT (light print out) a. Make sure the print head/cam lock assembly if fully locked in the closed position. b. Consult “Thermal Print Head” in Section 8.1.2. c. Clean print head. Consult “Thermal Print Head” in Section 8.1.2. d. Adjust print intensity setting via the control panel (see Appendix A) e. Replace thermal head. 7. POOR PRINT OUT (white voids in print out) a. Clean print head. Consult “Thermal Print Head” in Section 8.1.2. b. Replace thermal head. 8. NO PRINT OUT a. Check head cable for electrical connection at both ends. b. Check to make su

  • Boca Systems Adjustable MC Ghost, JUST EXIT? Will exit the menu options without saving any changes. If you with to exit without saving the new value then press TEST, if not press MENU. To access and use the SPECIAL MENU, follow steps 1 - 6 under the OPERATOR MENU except press both the TEST and Choice switch simultaneously for three seconds. The following chart below lists the present menu topics in the SPECIAL MENU. The following is an overview of what each Menu Option does: PRINTER TYPE? Is not used by this printer. It automatically determines if it is a Boarding Pass or a Bag Tag printer. FLIGHT

  • Boca Systems Adjustable MC Ghost, 7.0 Thermal Paper - Theory & Specification The print head’s life expectancy is composed of both a mechanical and an electrical component. Both of these factors are strongly influenced by the quality of the thermal paper used. MECHANICAL The print head has a theoretical rating of 60 kilometers. This number is based upon the assumption that the head will be used with a good quality, top coated thermal paper. Uncoated and poorly top coated thermal papers are abrasive to the print head and have been found to wear through the head after less than one kilometer. Other factors which may contrib

  • Boca Systems Adjustable MC Ghost, The position of the tear can be controlled by changing the cut count setting in the OPERATOR MENU (see Appendix A). If you are not able get the desired tear position, then make sure your ticket stock was manufactured to proper specifications. Once a month the opto eye should be blown off with air to remove any accumulated paper dust. A soft haired brush can also be used if air is not available. Figure 8a - Auto configuration opto and Load opto 10 Auto configuration opto Load opto Figure 8b - Print position and Tear opto Print position and tear position opto

  • Boca Systems Adjustable MC Ghost, The chart below lists the present menu topics. These topics are subject to change. OPERATOR MENU! BAUD RATE? MINI/MICRO? PRINT SPEED? DIAGNOSTIC MODE? TICKET TYPE? STATUS ENABLED? TRANSPARENT MODE PAPER MODE? INC BPP CUT COUNT? DEC BPP CUT COUNT? INC BTP CUT COUNT? DEC BTP CUT COUNT? PRINT MODE? PRINT INTENSITY? EXIT AND SAVE JUST EXIT The following is an overview of what each Menu option does: BAUD RATE? Controls the serial interface baud rate, parity bit, data bits and stop bits. Here are the following choices: 1200,N,8,1 1200,E,7,1 1200,O,7,1 2400,N,8,1 2400,E,7,1 2400,O,7,1 4800,N,8,1 4800,E,7,1 4800,O,7,1 9600,N,8,1 (factory defau

  • Boca Systems Adjustable MC Ghost, MINI/MICRO? Defines the type of printer. MINI Is for a printer with a Silent Cutter Assembly (SC2) ( Mini, Mini Plus, Mini MB, Dual Mini) MICRO Is for a printer without a SC2 (Micro, Micro Ghost, Micro MB, Dual Micro) (factory default) PRINT SPEED? Controls the speed the ticket travels at. Also effects the print quality. The numbers range from 0 - FASTEST to 7 - SLOWEST. 3 is factory default. DIAGNOSTIC MODE? Please consult your Programming Guide Your choices are YES or NO. NO is factory default. TICKET TYPE? Defines how the optos are configured on the paper guide assembly. NORMAL Both optos are inline with each other (usually mounted on a black bracket ) (factory default) ATM Feed opto is

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Makita 5704R Instruction manual makita/5704r-5K6.pdf 04 Nov 2023 28
2 A&D FY-3000 Instruction manual a-d/fy-3000-Q7Y.pdf 12 Sep 2022 27 1.1 Mb
3 AMX HPX-AC-TMPLT-600 Quick start manual amx/hpx-ac-tmplt-600-296.pdf 09 Sep 2023 2
4 Newco GKDF2-30 Installation, operation and service manual newco/gkdf2-30-4IH.pdf 07 Dec 2022 10
5 Atmel ATAK2270 Operation & user’s manual atmel/atak2270-37S.pdf 19 Apr 2023 39 3.83 Mb
6 Monarch 9855 HF Specifications monarch/9855-hf-538.pdf 24 Dec 2023 2

Similar Resources:

  • Sharp

    AR-D29

    (34 pages)
    CODE : 00ZqSERVICE MANUALCONTENTSParts marked with "!" are important for maintaining the safety of the set. Be sure to replace these parts with specifiedones for maintaining the safety and performance of the set.SHARP CORPORATIONThis document has been published to be usedfor after sales service only.The contents are subject to change without notice …
  • Epson

    R260 - Stylus Photo Color Inkjet Printer

    (8 pages)
    4106721 Rev.11-F C4106721 Rev.11-F M4106721 Rev.11-F Y4106721 Rev.11-F K1 Open the paper support and pull up its extension. Déployez le support à papier et tirez ses rallonges.2 Open the front cover and pull out the front tray extensions. Ouverez le plateau de sortie et tirez sa rallonge.3 Slide the edge guide to the left. Faites glisser le g …
  • Lexmark

    C746n

    (504 pages)
    Lexmark™ C746n, C746dn, C746dtn,C748e, C748de, C748dte, and CS748de5026-3xx, 5xx• Table of contents• Start diagnostics• Safety and notices• Trademarks• IndexLexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and or other countries.Revised: July 30, 2014 …
  • Ricoh

    Aficio SP C400DN

    (608 pages)
    1Safety InformationModel No.IntroductionThis manual contains detailed instructions and notes on the operation and use of this machine. For yoursafety and benefit, read this manual carefully before using the machine. Keep this manual in a handyplace for quick reference.Power Source120 V, 60 Hz, 11 A or morePlease be sure to connect the power cable to a power …
  • Canon

    EOS 450D

    (101 pages)
    1234IntroductionContents at a GlanceDownloading ImagesCamera SettingsRemote ShootingReferencePreferencesIndexCommunication Software for the CameraEOS UtilityVer. 2.11Instruction Manual1D X1D Mk IV1Ds Mk III1D Mk III5D Mk III5D Mk II7D60D50D40DREBELT4i650DREBELT3i600DREBELT2i550DREBELT1i500DREBELXSi450DREBELT31100DREBELXS1000D Content of this Instruction M …
  • NETGEAR

    WGPS606NA

    (17 pages)
    WGPS606 Print Server Windows XP Installation A Wireless Print Server allows one or two printers to be conveniently shared across a WiFi network. Wireless print servers for home networks generally are available in both 802.11b and 802.11g varieties. Make sure the printer work when directly connected to the computer and also check the printer drivers are in …

Comments, Questions and Opinions: