Manualios.com

Brocade Communications Systems MLX Series Installation Manual

Brocade Communications Systems MLX Series Manual Online:

4.25, 2899 votes
Brocade Communications Systems MLX Series User Manual
Brocade Communications Systems MLX Series User Guide
Brocade Communications Systems MLX Series Online Manual

Text of Brocade Communications Systems MLX Series User Guide:

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 59 53-1002373-02 Router modules 1 FIGURE 39 Front fan location for Brocade MLX and Brocade NetIron XMR 16-slot routers FIGURE 40 Rear fan location for Brocade MLX and Brocade NetIron XMR 16-slot routers 1 Front fan assembly 1 Rear fan assemblies 1 1

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 433 53-1002373-02 Dangers C DANGER The intra-building port or ports of the equipment or subassembly is suitable for connection to intra-building or unexposed wiring or cabling only. The intra-building port or ports of the equipment or subassembly MUST NOT be metallically connected to interfaces that connect to the outside plant (OSP) or its wiring. These interfaces are designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE, Issu

  • Brocade Communications Systems MLX Series, 396 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 53-1002373-02 Brocade MLXe Chassis bundles A TABLE 69 Brocade MLXe-4 chassis bundles Part number Hardware BR-MLXE-4-AC Bundle contents: • 1 Brocade MLXe-4 chassis • 2 high speed switch fabric modules (NI-X-4-HSF) • 1 1200W AC power supply (NI-X-ACPWR) • 4 exhaust fan assembly kits (BR-MLXE-4-FAN) • 1 air filter (BR-MLXE-4-FLTR) Management modules must be ordered separately. Power cord is not included. BR-MLXE-4-DC Bundle contents: • 1 Brocade MLXe-4 chassis • 2 high speed switch fabric modules (NI-X-4-HSF) • 1 1200W DC power supply (NI-X-DCP

  • Brocade Communications Systems MLX Series, 16 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 53-1002373-02 Hardware features 1 Brocade NetIron XMR 32000 router components You can install the following components in the router slots: • Up to two management modules (one active and one redundant). • Up to eight switch fabric modules. • Up to 32 interface modules. • Up to eight power supplies (AC or DC). Figure 12 displays the Brocade NetIron XMR 32000 router. FIGURE 12 Brocade NetIron XMR 32000 router r 44 45 43 43 Pwr Active Pwr Active Pwr Active Pwr Active 357 91 2468 10 1133 35 34 36 41 12

  • Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 427 53-1002373-02 Dangers C DANGER Disconnect the power cord from all power sources to completely remove power from the device. GEFAHR Ziehen Sie das Stromkabel aus allen Stromquellen, um sicherzustellen, dass dem Gerät kein Strom zugeführt wird. DANGER Débranchez le cordon d'alimentation

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 205 53-1002373-02 Installing a Brocade MLX-32 router 3 10. Visually inspect the alignment of the router. If the router is installed properly in the rack, the mounting screws on one side of the rack should align with the mounting screws on the opposite side and the router should be level. Add all remaining screws. NOTE For better grounding of the router to the rack, attach the router using star washers. You should also use star washers with any single-hole grounding lugs to keep

  • Brocade Communications Systems MLX Series, 8 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 53-1002373-02 Hardware features 1 Brocade MLX routers Brocade MLX routers are available in the following models: • Brocade MLX-4: 4 interface slots (see Figure 5 on page 8) • Brocade MLX-8: 8 interface slots (see Figure 6 on page 9) • Brocade MLX-16: 16 interface slots (see Figure 7 on page 10) • Brocade MLX-32: 32 interface slots (see Figure 8 on page 12) The following sections described the components you can install in the router slots. Brocade MLX-4 router components You can install the following components in the router slots: • Up to

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 207 53-1002373-02 Installing a Brocade MLX-32 router 3 3. Adjust the telescoping rails to fit your rack. The rails can accommodate rack depths from 27 - 31 inches. 4. Attach the side rails to the front and back of the rack, using screws appropriate for your rack type. (You must provide these screws). Refer to Figure 144. NOTE The narrow telescoping ends of the side rails should attached at the back of the rack. FIGURE 144 Attach the telescoping side rails to the rack. 5. Use the mechanical lift

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 255 53-1002373-02 Installing a Brocade NetIron XMR 8000 router 4 FIGURE 178 Mounting the Brocade NetIron XMR 8000 router in a rack (front-mount configuration) 4. Slide the router down so that the screw heads are in the narrow portion of the keyhole slots. 5. Tighten the screws to secure the router. NOTE For better grounding of the router to the rack, attach the router using star washers. You can also use star washers with single hole grounding lugs to prevent rotation of the lug. 6. Add additional screws as required. 7. Repeat step 2 through step 6 to mount each router in the rack. Installing Brocade NetIron XMR 8

  • 386 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 53-1002373-02 Hardware specifications for Brocade MLX routers 9 Physical dimensions Table 59 provides the physical dimensions for Brocade MLX routers. Operating environment Table 60 provides the operating environment specifications for Brocade MLX routers. Storage environment Table 61 provides the stora

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 43 53-1002373-02 Router modules 1 Power supply requirements for NI-MLX-1Gx48-T-A modules Table 21 lists the power supply requirements for each type of router when installing NI-MLX-1Gx48-T-A modules. NOTE When one or more NI-MLX-1GX48-T-A modules are installed in an MLX16-slot router, you must replace the NI-X-16-FAN-EXH modules with NIBI-16-FAN-EXH-A high-speed fan modules. For more information about high-speed fan modules, see “NIBI-16-FAN-EXH-A high-speed fan assemblies” on page 61. If the 16-slot router is not upgraded to support NIBI-16-FAN-EXH-A modules before NI-MLX-1GX48-T-A modules are ins

  • 332 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 53-1002373-02 Managing the cooling system 7 • If the temperature of a management module, switch fabric module, or one interface module exceeds the high threshold specified for a fan speed, the fan changes to the next higher speed. If the temperature of any of the modules exceeds the high th

  • Brocade MLX Series and NetIron XMR Hardware Installation Guide 235 53-1002373-02 Chapter 4 Installing a Brocade NetIron XMR Router This chapter describes how to install a Brocade NetIron XMR router and its modules in the following sections: • “Installation precautions” on page 235 • “Installing 2x100GbE interface modules in Brocade MLX routers” on pag

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 359 53-1002373-02 Replacing fan assemblies 8 7. For a 4-slot device only, use the screwdriver to secure the two screws on either side of the power supply faceplate. 8. For a 2400W DC power supply only, crimp the #4 AWG power supply wire in the power lugs. 9. For a 3000W DC power supply only, crimp the #2 AWG power supply wire in the power lugs. 10. Connect the AC power cord or DC power lugs to the power supply faceplate. 11. Connect the power to t

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 425 53-1002373-02 Cautions C CAUTION For a Brocade NetIron XMR 32000 AC system, use a ground wire of at least 6 American Wire Gauge (AWG). The ground wire should have an agency-approved crimped connector (provided with the chassis) attached to one end, with the other end attached to building ground. The connector must be crimped with the proper tool, allowing it to be connected to both ground screws on the enclosure. VORSICHT Für ein

  • Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 423 53-1002373-02 Cautions C CAUTION Removal of Brocade NetIron XMR 32000 rear fan modules allows access to bus bars and backplane. Avoid contact with these parts. There are hazardous energy levels at these locations. VORSICHT Durch die Entfernung der rückwärtigen Brocade NetIron XMR 32000 Ventilatormodule wird der

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 365 53-1002373-02 Replacing fan assemblies 8 Replacing the fan tray assembly in 4-slot and 8-slot routers The fan tray assembly on Brocade MLX and Brocade NetIron XMR 4-slot and 8-slot routers is accessible from the front of the device. Fan tray assemblies for Brocade MLXe 4-slot and 8-slot routers are accessible from the back of the device. You can remove and replace a fan tray assembly while the router is powered on and running. To replace a fan tray assembly, have these items available: • A n

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 85 53-1002373-02 Installing a Brocade MLXe-8 router 2 NOTE When inserting the module into the router, be sure that the faceplate does not overlap the faceplate of an adjacent module. 5. Rotate the ejectors until they are flush with the module faceplate. This action will fully seat the module in the backplane. 6. Tighten the screws at each end of the module faceplate by pushing them in and turning them clockwise. Complete the tightening process using the flat-blade screwdriver. 7. E nter the write mem

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 369 53-1002373-02 Replacing fan assemblies 8 FIGURE 240 Air filter removal and replacement for 32-slot routers Replacing the air filter in Brocade MLX and Brocade NetIron XMR 16-slot routers Follow these steps to replace the air filter in a Brocade MLX or Brocade NetIron XMR 16-slot router. 1. Loosen the two screws in the front of the filter retainer. 2. Pull the filter retainer away from the router as shown in Figure 241. There is a hook on the back of the retainer that i

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 421 53-1002373-02 Cautions C CAUTION Do not install the device in an environment where the operating ambient temperature might exceed 40 C (104 F). VORSICHT Das Gerät darf nicht in einer Umgebung mit einer Umgebungsbetriebstemperatur von über 40 C (104 F) installiert werden. MISE EN GARDE N'installez pas le dispositif dans un environnement où la température d'exploitation ambiante risque de dépasser 40 C (104 F). PRECAUCIÓN No ins

  • Brocade Communications Systems MLX Series, 294 Brocade MLX Series and NetIron XMR Hardware Installation Guide 53-1002373-02 Installing a Brocade NetIron XMR 32000 router 4 FIGURE 208 Removing the power lugs (2400W power supply and 3000W power supply displayed) 3. Crimp the correct AWG wire into the power lugs: For 2400 W power supply, crimp #4 AWG For 3000 W power supply, crimp #2 AWG. Refer to Figure 209. CAUTION For the NEBS-compliant installation of a Brocade NetIron XMR 4000, 8000, and 16000 routers with AC and DC systems, use a ground wire of at least 6 American Wire Gauge (AWG). The ground wire should have an agency-approved crimped connector (provided with the router) attached to one

  • Brocade Communications Systems MLX Series, 334 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 53-1002373-02 Managing the cooling system 7 For the <low-threshold> and <high-threshold> parameters, you can specify any temperature in Centigrade. However, when changing low and high temperature thresholds for module fan speeds, remember that the low temperature threshold of a higher fan speed must be lower than the high temperature threshold of the lower fan speed. Brocade has established this guideline to ensure fan speed stability. For example, if

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 61 53-1002373-02 Supported software features 1 The 32-slot router fan control modules include a bi-color LED, which indicates the status of the fans. Table 26 describes the states for this LED. The router ships with fan assemblies fully installed. Fan assemblies are hot-swappable, which means you can remove and replace them without powering down the system. NIBI-16-FAN-EXH-A high-speed fan assemblies NIBI-16-FAN-EXH-A high-speed fan assemblies are required for Brocade MLX Series 16-slot routers when you instal

  • Brocade Communications Systems MLX Series, 418 Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 53-1002373-02 Cautions C CAUTION For the DC input circuit to the system of a Brocade MLX-4, Brocade MLX-8, Brocade MLX-16, and Brocade MLXe-16, Brocade MLXe-8 and Brocade MLXe-4 (1200W supply), make sure there is a UL-Listed 30 amp circuit breaker, minimum -48Vdc, double pole, on the input lugs to the power supply. The input wiring for connection to the product should be Listed copper wire, 8 AWG, marked VW-1, and rated minimum 90o C. VORSICHT Bei

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 355 53-1002373-02 Replacing a power supply 8 NOTE A threshold value of 0 will not automatically shutdown a power supply due to failures. For Syslog messages, please refer to Appendix A, Using Syslog in the Brocade MLX Series and Brocade NetIron Family Configuration Guide. Clearing power supply failure timestamps Use the power-supply monitoring clear command to clear all collected failure timestamps for a given power supply, or for all available power supplies. To clear all collected failure timestamps for a power

  • Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 389 53-1002373-02 Hardware specifications for Brocade NetIron XMR routers 9 NOTE At power-up or during the hot swap of an interface module, the system checks to make sure that the router remains within the power budget. If not, modules exceeding the power budget are prevented from becoming active. Physical d

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 177 53-1002373-02 Installing a Brocade MLX-16 router 3 FIGURE 125 Positioning the mounting screws in the rack posts 3. Starting at the bottom of the rack, mount the router as shown in Figure 126. With two or more people lifting the router, slip the wide portion of each keyhole slot over the corresponding mounting screw in the rack post. FIGURE 126 Mounting the Brocade MLX-16 router in a rack 4. Slide the router down so that the mounting screw heads are in the narrow portion of t

  • Brocade Communications Systems MLX Series, Brocade MLX Series and Brocade NetIron XMR Hardware Installation Guide 49 53-1002373-02 Router modules 1 Switch fabric modules switch packets from one interface module to another. Brocade MLX Series and Brocade NetIron XMR routers can be configured with multiple switch fabric modules as described: • 4-slot router: Accommodates three switch fabric modules (two required and one redundant) for a fully-loaded system. Ships with two switch fabric modules. You must purchase an additional switch fabric module to equip your router for redundancy. • 8-slot router: Accommodates three switch fabric modules (two required and one redundant) for a fully-loaded system. Ships with two swi

Related Products and Documents (Network Router):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Closet Maid Stackable Storage Organizer SO16 Instruction sheet closet-maid/stackable-storage-organizer-so16-R1Q.pdf 05 Nov 2023 2 3.74 Mb
2 Breville TF40 User manual manual breville/tf40-T5L.pdf 26 Oct 2023 36 0.44 Mb
3 Philips CD5653B/05 Quick start manual philips/cd5653b-05-Y75.pdf 19 Nov 2023 6 1.41 Mb
4 Novell SENTINEL 6.1 SP1 HOTFIX 1 - READ ME 7-8-2009 Manual  novell/sentinel-6-1-sp1-hotfix-1-read-me-7-8-2009-15X.pdf 10 Aug 2023 8
5 Toshiba 55UL610U Energy manual toshiba/55ul610u-5XS.pdf 22 Sep 2023 1 0.31 Mb
6 Tech 21 Killer Wail Owner's manual tech-21/killer-wail-6B7.pdf 21 May 2023 2 0.08 Mb

Similar Resources:

  • BEC

    6300VNL

    (120 pages)
    Last revised: October 17, 2013 BEC 6300VNL GigaConnect® 4G/LTE VoIP Wireless Broadband Router User Manual Version release: v1.02 …
  • Moxa Technologies

    NPort IA5150 series

    (6 pages)
    P/N: 1802051500214 *1802051500214* NPort IA5150/5250 Series Quick Installation Guide Edition 6.0, April 2016 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777 Fax: 1-714-528-6778 Moxa China (Shanghai office): Toll-free: 800-820-5036 Tel: +86-21-5258-9955 Fax: +86-21-5258-5505 Moxa E …
  • ADTRAN

    SMART/RG SR555ac

    (154 pages)
    / Gateway User ManualModel: SR555acRelease 1.6 March 2020Firmware Version: 2.6.2.4501 SE Columbia Shores Boulevard, Suite 500Vancouver, Washington 98661 USA+1 360 859 1780 / smartrg.com …
  • Asante

    GX5

    (9 pages)
    FriendlyNET® GX5 Gigabit Ethernet Switches New! The FriendlyNET GX5 family includes the smart GX5-2400W (top) and GX5-424W (bottom) PRODUCT LINE GUIDE “Most of the news in LAN product introductions these days is coming from smaller companies, rather than the big names. Whatever the case, it seems like there have been mor …
  • Cisco

    828

    (10 pages)
    Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USACopyright © 2001. Cisco Systems, Inc. All rights reserved.78-12839-01Cisco 828 Router and SOHO 78 Router Cablingand Setup Quick Start GuideThis document describes the basic process of cabling and configuring the Cisco 828 router and theSOHO 78 router. For advanced …
  • H3C

    S3100 Series

    (1057 pages)
    H3C S3100 Series Ethernet SwitchesOperation ManualHangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document Version: 20100908-C-1.00 Product Version: Release 22XX Series …

Comments, Questions and Opinions: