Buhler 595 Assembly, Operator's And Parts Manual

Text of Buhler 595 User Guide:

• Buhler 595, 14 Attaching the Loader to Your Tractor 1. Position the tractor as centrally as possible and drive, using lowest gear possible, into the loader frame until hoses can be connected. 2. Couple up the hydraulic hose lines to the loader or tractor valve ensuring proper function (see Operator and Maintenance Section) NOTE: When mounting the loader for the first time, slowly work the cylinders back and forth, so that most of the air is removed. Loosen the bolts on the hooks so that they can be moved. Also, check that the nuts in the rear of the subframes are in line with the holes.

• 6 Safety • Never work beneath raised loader unless it is securely supported. The following are instructions for the Lift Lock Supports; -DO NOT USE WHEN TRACTOR IS MOVING. -DO NOT STORE LIFT LOCK SUPPORTS OTHER THAN WHERE INDICATED. -REPLACE IMMEDIATELY IF DAMAGED. -THE BUCKET MUST BE EMPTY -ALWAYS USE BOTH SUPPORTS TO DISENGAGE SUPPORTS: 1. RAISE LOADER OFF LIFT LOCK SUPPORT

• Item Part No. Description 3.0 Dia. C yl. Quantity 1 24726 3.0 DIA x 22.0 Cyl. Assy. Bucket 2 2 24408 3.0 DIA x 28.5 Cyl. Assy. Lift 2 3 812069 Tee 3/4-16MJIC X 3/4-16 MJIC 8 4 811414 Elbow 90º 3/4-16 MORB to 3/4 MJIC 2 5 812128 Elbow 90º 3/4 MJIC x 3/4 MJIC 2 6 11362 Pipe Clip 9 7 113031 Tubing Ext. Lift Cyl 23.0" 2 8 114114 Tubing Lift Cyl. (Bottom, Raise) 1 9 114115 Tubing Lift Cyl. R

• Buhler 595, 8 Safety Decals These decals are located as shown on the Decal Location diagram and the Sub-Frame Assembly diagram. 1. Read Operator's Manual before operating. 2. Move and turn tractor at low speed. 3. Carry loader arms at a low position during transport. 4. Lower loader arms, stop engine and lock brakes before leaving operator seat. 5. Do not stand or work under raised loader, unless properly supported. 6. Add recommended wheel ballast or rear weight for stability. 7. Move wheels to widest recommended settings to increase stability. 8. Do not handle large round bales or other shiftable objects

• Buhler 595, 3 Pre-delivery Check List Before delivering this equipment please complete the following check list. 1. The loader has been installed using the appropriate mounting kit for the tractor and loader. 2. The hydraulic system installed is appropriate for the tractor and loader 3. The loader is properly installed. 4. All bolts are tightened to the torque specifications shown in the torque chart. 5. All safety decals are readable. 6. The loa

• Buhler 595, 30 595, S595, 595TSL, S595TSL Hydraulic Cylinder Assembly Bucket Cylinders Bucket Cylinders TSL Bucket Cylinders Lift Cylinders Lift Cylinders Diameter 2.50" 3.00" 3.00” 2.50" 3.00" Length of Stroke 20.63" 20.63" 22.00” 28.50" 28.50" Retracted Length 33.00" 33.00" 47.50" 38.00" 38.00" Extended Length 53.63" 53.63" 69.50" 66.50" 66.50" Cylinder Assembly No. 24458 24407 24726 24454 24408 Seal Kit No. X1110 X1656 X1424 X1110 X1424 Shaft Diameter 1.50" 1.50" 1.75” 1.5

• Buhler 595, Buhler Manufacturing “ a partnership” 1260 Clarence Ave Winnipeg, MB. R3T 1T2 Ph.: (204) 661-8711 Fax: (204) 654-2503 www.buhler.com Printed in USA Allied Division 1260 Clarence Ave Winnipeg, MB. R3T 1T2 Ph.: (204) 661-8711 Fax: (204) 654-2503 Farm King Division 301 Mountain Street S. Morden, MB R6M 1X7 Ph.: (204) 822-4467 Fax: (204) 822-6348 Inland Division 675 Washington Ave. Winnipeg, MB R2K 1M4 Ph: (204) 667-7854 Fax: (204) 669-2599 B.I.I. Division 1330 43 rd Street N.W. Fargo, ND 58102 Ph: (701) 282-7014 Fax: (701) 282-5865 B.C., Abbotsford

• Buhler 595, 15 Attaching the Loader to Your Tractor (Continued) 6. When the hook is lined up, dump or roll back the bucket to lower or raise the subframe upright to align with the mounting boot. 7. Continue to drive the tractor forward until the subframe uprights are seated in the boot. 8. Secure the subframe uprights with the bolts and washers. Torque to 500 ft-lbs. IMPORTANT: When mounting for the first time, the front hook bolts will have to be tightened after positioning the hook directly over the mounting boss (most rearward position). 9. Raise the l

• Buhler 595, 10 General Instructions and Information As with any piece of equipment, the care with which your loader is operated and maintained will greatly affect it’s life and the safety of the people using it. 1. Keep all pivots well lubricated for longer bushing life. Inspect every 500 hours of operation for wear. 2. Periodically check all bolts for tightness. If any bolt is damaged, replace it with a bolt of equivalent grade or strength. 3. Follow the recommendations of the tractor manufacturer in regards to the quantity of oil used. 4. Check oil level frequently to ensure the sy

• Buhler 595, PRINTED IN CANADA WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications. Buhler Manufacturing’s obligations under this warranty shall be limited to the repair or exchange, at Buhler Manufacturing’s option, of any Buhler Manufacturing product or part which proves to be defective as provided. Buhler Manufacturing reserves the right to either inspect the product at the buyer’s loca

• Buhler 595, Item Part No. Description Regular Quantity TSL Quantity S595 Quantity S595 TSL Quantity 1 25440 595 Sub Frame Weldment Left 1 - 2 25441 595 Sub Frame Weldment Right 1 -- - 1 25457 595 S Sub Frame Weldment Right - - 1 - 2 25458 595 S Sub Frame Weldment Left - - 1 - 3 110959 Hook Weldment 2 2 2 2 4 112747 Plate Clamp 2 2 2 2 5 112746 Spacer Block 4 4 4 4 6 112748 Shim 2 2 2 2 7 112663 Cross Member Weldment 1 1 1 1 8 812882 Bolt Car. 0.625nc X 2.50 gr5 pl 4 4 4 4 9 112642 Shaft Pivot 1.75 DIA X 5.50 Long 2 2 2 2 10 113281 Bolt Retainer Weldment 2 2 2 2 11 110887 Loader Lift Lock Weldment 2 2 2 2 12 8

• Buhler 595, 13 Operating Suggestions For Backfilling DO THIS! When backfilling approach pile with a flat bucket. Leave dirt in bucket. Dumping on each pass wastes time. NOT THIS! DO NOT use bucket in dumped position for bulldozing. This will only impose severe shock loading on the bucket cylinders and make it more difficult to maintain a level grade. Backgrade work surface with a loaded bucket. Release all pressure on lift cylinders so full weight of bucket is

• Buhler 595, Item Part No. Description 595 595 S 1 25442 595 Main Frame Weldment 1 - 1 25443 595 S Main Frame Weldment - 1 2 24296 Quick Attach Weldment Left 1 1 3 24297 Quick Attach Weldment Right 1 1 4 112798 Tube Cross Qtach 2 1 5 108827 Pin Weldment 2 2 6 111231 Stand Weldment 2 2 7 113114 Strap Stand 2 2 8 24329 Wrench Mounting 1 1 9 110907 Pin 0.625 Dia. Stand 2 2 10 12779 Hair Pin Clip #9 Western Wire 5 5 11 113109 Levelling Rod 1 1 12 117365 Pin 1.25 Dia. x 5.13 Long 4 4 13 117364 Pin 1.25 Dia. x 4.50 Long 4 4 14 117371 Pin Qtach 4 4 1

• 7 Important Precautions ROLL-OVER HAZARD To prevent serious injury or death: Move and turn tractor at low speed. Carry load no higher than necessary to clear the ground when transporting. Add wheel ballast or rear weight for stability. Move wheels to widest possible settings to increase stability. It is recommended the tractor be equipped with a rol

More Instructions:

Buhler 595 Assembly, operator's and parts manual 30-10-2022 38

DOWNLOAD

Related Products and Documents (Washer):

Comparable Devices:

Similar Resources:

• Indesit IWSC 51051 (4 pages) GB1ContentsInstallation, 2-3Unpacking and levellingConnecting the electricity and water suppliesThe first wash cycleTechnical dataCare and maintenance, 4Cutting off the water or electricity supplyCleaning the washing machineCleaning the detergent dispenser drawerCaring for the door and drum of your applianceCleaning the pumpChecking the water inlet hosePreca …

• SciCan hydrim c51w (2 pages) Hydrim®C51w Quick Reference Guideorder number 01-108148SFor best results:Always use the heavy duty cycle for cassettes, hinged instruments, heavily soiled instruments and the cannula post adapter.Do not allow instruments to dry for more than one hour prior to processing in the Hydrim.Remove all cement, composite material and amalgam at chairside prior to pr …

• KRAFT KF-SM60102MWL (30 pages) СТИРАЛЬНАЯ МАШИНААВТОМАТAUTOMATIC WASHING MACHINEmodel: KF-SM60102MWL / KF-SM60103MWLSmodel: KF-ST60102MWL / KF-ST60103MWLSИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИUSEr GUIdEwww.kraftltd.comТелефон службы поддержки клиентов:8 (800) 200-79-97Надежно! Выгодно! Доступно!Safe! Re …

• Alliance Laundry Systems CHD25G2 (156 pages) www.comlaundry.comTroubleshootingPart No. 70380601R3September 2009Drying Tumblers25 Pound Capacity30 Pound Capacity35 Pound Capacity55 Pound CapacityStarting Serial No. 0602004144Refer to Page 7 for Model NumbersSTART25CHIGHTEMPMEDTEMPLOWTEMPNOHEAT123SELECTTEMPINSERTCOINPUSHSTART …

• Maytag MVP5000TQ0 (12 pages) _ TMWh ol°o Dlaundry 0custom laundry options i/_MzAY£AG TMLAUNDRYTOWERJORGANIZADORDELAVANDERIAORGANISATEURDEBUANDERIETableof Contents/In(tlce / Tabledes matDresLAUNDRY TOWER SAFETY ........................... 1INSTALLATION REQUIREMENTS ................. 2Tools and Parts ............................................. 2Location Requirements .................. …

• GE GTUN275EMWW (36 pages) MATERIALS YOU WILL NEEDGLOVESSAFETYGLASSESAPPLIANCE POWERCORD KIT(NOT PROVIDED)4" DUCTCLAMPS (2)OR4" SPRINGCLAMPS (2)EXHAUSTHOOD3/4" STRAINRELIEFUL RECOGNIZED4" DIA. METALELBOWDUCT TAPEUL RATED 120/240V,30A WITH 3 OR 4 PRONGS. IDENTIFY THE PLUG TYPE AS PER THE HOUSE RECEPTACLE BEFORE PURCHASING LINE CORD. 4" DIA. FLEXIBLE METAL …

Comments, Questions and Opinions: