Bulldog Security 1402 Installation And Owner's Manual

Text of Bulldog Security 1402 User Guide:

• Bulldog Security 1402, CONTENTS KEYLESS ENTRY AND ALARM SYSTEM • MODEL 1402 INSTALLATION GUIDE • OWNER’S GUIDE Technical Assistance All tech personnel are expertly qualified to answer any technical questions. Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m. Address 288 Canton Avenue • Wintersville, Ohio 43953 Telephone Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306 System Features ....................................... 1 System Components ..................................... 1 Required Tools .......................

• Bulldog Security 1402, SYSTEM FEATURES SYSTEM COMPONENTS 1 2 Four-Button Extended Control your car from an extended distance. Range Remote Control Keyless Entry Remotely locks and unlocks your power door locks. Remote Locking and Remotely locks your power door locks when the ignition is turned on and Unlocking with Ignition unlocks your power door locks when the ignition is turned off. NOTE: This Switch feature can also be used while the unit is wired as an alarm. Remote Valet Lets you program off the alarm section when it is not needed. Remote Full Time This system will perform all its functions except no

• TECHNICAL ASSISTANCE Should you need help. First check our website at www.bulldogsecurity.com/wires.htm or call our toll-free Tech Support Hotline Monday through Friday 9AM-8PM and Saturday 10AM-4PM EST at 800-878-8007. You must give the following information: •Name •Telephone Number with Area Code (Fax number if applicable) •Year, Make, and Model of the vehicle •The mod

• Bulldog Security 1402, MAKING WIRING CONNECTIONS 4. Insert the wire from the unit through the hole as shown. 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together. Use this method for all connections. CAUTION: All wires must be wrapped and taped. 5. Wrap the wire around one side then the other and finally around itself as shown. 1 2 3 Wire Tie Electrical Tape 1. Strip back two inches

• Bulldog Security 1402, 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 2. Twist upper wires together, twist lower wires together as shown. Use this method ONLY when connecting two separate wires end to end. Wire Tie Electrical Tape Wire Tie Please see the wiring chart on our website, www.bulldogsecurity.com. LOCATING & MAKING CONNECTIONS 4 CONSTANT POWER (+12V, key in any position including o

• Bulldog Security 1402, 5 CONNECTING THE POWER AND GROUND 1. Connect the RED wire from the harness to a constant 12 volt supply or to the wire you ran from the positive battery post (if no constant 12 volt supply was found at the ignition switch harness). 2. Connect the BLACK wire from the harness to a clean chassis ground, usually a steel automotive body part connected to the negative side of the battery. CONNECTING IGNITION POWER 1. Connect the YELLOW wire from the harness to the wire market Ignition Power. FINDING THE PARKING LIGHT WIRE (optional - included) To have the parking lights flash when using keyless entry or during a violation, you must connect the 1402 to the vehicle’s parking light

• Bulldog Security 1402, 6 Connect the control module ORANGE wire negative (-) out when armed to the optional starter disable relay (-) negative input. Pin 86 on SPDT 30 amp relay or use part #PRO1010 and relay #30-ARB To connect “Key Side” and “Starter Side” of the cranking wire to the optional relay for Starter Disable. Use a wire tie to secure the starter disable relay to a non-moving part under the dash. DETERMINING YOUR VEHICLE’S DOOR PIN SWITCH TYPE NOTE: For your alarm system’s arming feature to work, you must connect the alarm to

• 7 the system. •To prevent water damage, the siren should NOT be mounted in a wheel well, directly behind the radiator grill or close to the ground. •Mount the siren as far away from sources of heat, i.e. exhaust manifold, turbo charger, etc. as possible. Tape, wrap or tube all wires. Run all wires to the siren as high up in the engine compartment as pos

• Bulldog Security 1402, 8 RED (+) 12 Volt Constant BLACK Chassis Ground BROWN (+) Parking Light Output ORANGE* (-) Output when armed; starter disable, etc. YELLOW (+) 12 Volt Ignition Sense Input Ignition Harness (or) Fuse Box BLUE* (+) Lock or (-) Unlock Output 200ma Max GRAY* (-) Output to Horn Relay 200ma Max (or) Optical Siren Output WHITE/ORANGE* Button #2 / Channel #2 (-) Output; Remote Start, Etc. 200ma Max BLUE/WHITE* (+) Unlock or (-) Lock Output 200ma Max PURPLE* (-) Output Dome Light Supervision 200ma Max (+) Door Pin Input / 20 Second Delay After Arming GREEN/WHITE (-

• Bulldog Security 1402, OPERATOR PROGRAMMING INSTRUCTIONS ENTERING PROGRAMMING MODE Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want to remain in programming mode. The only exception is when a different remote has been learned. The unit will exit the programming mode simply by releasing the brake and the parking lights will flash three (3) times. PROGRAMMING FOR KEYLESS ENTRY TO PROGRAM IGNITION CONTROLLED DOOR LOCKS ON A.Turn the ignition switch on vehicle to the on or run position. B.Press a

• Bulldog Security 1402, 10 A.Turn the ignition switch to the on or run position. B.Press and hold button #1 on the transmitter for approximately 10 seconds or until parking lights flash once. C. Press and release button #2 on the transmitter. The parking lights will flash twice and the LED begins to flash. D.Press and release button #3 on the transmitter. The parking lights will flash once. System is now in silent arming mode. E.Turn the ignition switch off. The parking lights will flash 3 times and the LED will stop flashing. TO PROGRAM FULL TIME SILENT ARMING OFF Repeat above procedure.

• Bulldog Security 1402, 11 PROGRAMMING TABLES TO ENTER OPERATING PROGRAMMING MODE A. Turn the ignition switch to the on or run position. B.Press and hold transmitter button #1 for approximately 10 seconds or until the parking lights flash once. C. Press one of the following buttons to go to the following tables: BUTTON FLASHES SETTING 2 2 TABLE #1 3 3 TABLE #2 4 4 TABLE #3 NOTE: Bold items are factory default settings. Once you enter a programming table, you must start the procedure over to enter a different table. TABLE

• HOW TO USE YOUR REMOTE TRANSMITTER 12 2 3.5 sec. Door Lock Pulse Length 2 1 Negative Input Activated 2 Negative Input Deactivated 3 1 Siren Tone Output 2 Car Horn Output 4 1 Positive Door Pin Input 2 Negative Door Pin Input TABLE FIVE BUTTON FLASHES SETTING 2 1 Delayed Dome Lights Activated 2 Delayed Dome Lights Deactivated TO EXIT PROGRAMMING MODE Turn the ignit

• Bulldog Security 1402, 13 This feature is useful when having your vehicle valet parked, washed or serviced. While in valet mode, keyless entry and instant panic will still work; however, the alarm will not arm. Valet mode may also be programmed while the engine is running. Arming Press transmitter button #1 to arm the system. The siren will chirp or the horn will sound once. The parking lights will flash once, the power door locks will lock (if installed) and the LED will flash slowly indicating the alarm is now armed. The engine starter is also disabled (if installed). DISARMING Pressing transmitter button #1 again will disarm the system. The siren will chirp or the horn will sound

More Instructions:

	Bulldog Security 1402 Installation manual 02-01-2023 14	DOWNLOAD
	Bulldog Security 1402 Owner's manual 03-01-2024 14	DOWNLOAD

Related Products and Documents (Car Alarm):

Comparable Devices:

Similar Resources:

• Ultra Start 1500 SERIES (12 pages) WWW.ULTRASTARTERS.COM150015001500MINSTALLATION GUIDEAdvanced Remote Vehicle StarterN VersionTECH SUPPORTWestern Canada 1 800 279-0636United States: 1 866 698-5872Eastern Canada. Bilingual Support: 1 800 268-0683 E-Mail Tech Support: [email protected] Our Web Site: www.ultrastarters.com1500 Automatic and Manual Trans …

• Ampire WFS400 (16 pages) ampireWFS400German Engineering. Out of the ordinary.BedienungsanleitungOwner´s ManualBitte lesen Sie die komplette Anleitung aufmerksam durch, bevor Sie mit der Installation beginnen.Before attempting to connect or operate this product, please read the instructions completely. …

• Fox FAI-8200 (13 pages) 1FAI-8200 2-Way Color LED FM technology Security System Features 1. 1 Two Way LED Remote Transmitter and 1 one way 2nd remote 2. Code Hopping and Code Learning Remote System 3. Up to 4 LED remote transmitters Programmable 4. Remote Engine Start 5. Remote Arm/Disarm 6. Mute Arm/Disarm 7. Starter Kill (500mA negative output) in arming mode 8. Remote …

• Prestige 1286458 (16 pages) 128-64581 of 16Model APS-255CHInstallation ManualNote : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pinswitch in order to begin the passive arming sequence.RF Programmable Features :Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps Default1st Door L/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec.2nd Accy Lo …

• Xpresskit DLPK (20 pages) DLPKCANBUS DOORLOCK AND IMMOBILIZER INTERFACE**RFLOOP may be requiredINSTALLATIONGUIDE© 2009-2011 Directed Electronics. All rights reserved.www.xpresskit.comtmRev: 20110329DIGITAL OEM INTEGRATIONUpdate Alert: Firmware updates are posted to the web on a regular basis. We recommend you check for firmware and/or install guide updates prior to installation of t …

• Fortin Evo All THAR-VW2 (6 pages) * HOOD PINHOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF. CONTACTDE CAPOTMANDATORY INSTALL | INSTALLATION OBLIGATOIRENotice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed. Notice: l'installati …

Comments, Questions and Opinions: