Manualios.com

Bush Hog GHM 1800 Operator's Manual

Bush Hog GHM 1800 Manual Online:

3.15, 2957 votes
Bush Hog GHM 1800 User Manual
Bush Hog GHM 1800 User Guide
Bush Hog GHM 1800 Online Manual

Text of Bush Hog GHM 1800 User Guide:

  • Bush Hog GHM 1800, CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as well as suggestions for operation and maintenance. If your manual should become lost or destroyed, Bush Hog will be glad to provide you with a new copy. Order from Bush Hog, P. O. Box 1039, Selma, Alabama 36702-1039. Most of our manuals can also be downl

  • Bush Hog GHM 1800, GHM HAY MOWER TABLE OF CONTENTS SECTION/PARA PAGE Warranty.......................................................3 Dealer Preparation Check List.....................4 Safety Precautions.......................................5 Federal Laws and Regulations ....................6 I. INTRODUCTION & DESCRIPTION ............7 1-1 Introduction............................................7 1-2 Description.............................................7 II. PREPARATION FOR USE...........................8 III.OPERATING INSTRUCTIONS..................10 3-1 General Safety.....................................10 3-2 Cutting Height........................

  • Bush Hog GHM 1800, BUSH HOG ® LIMITED WARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by th

  • Bush Hog GHM 1800, DEALER PREPARATION CHECK LIST GHM HAY MOWER BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. ❒ 1. Assembly completed. ❒ 2. Gearbox filled with oil. ❒ 3. All fittings lubricated. ❒ 4. All shields in place and in good condition. ❒ 5. All fasteners torqued to specifications given in Torque Chart. ❒ 6. All decals in place and readable. (See decal page.) ❒ 7. Overall condition good (i.e. paint, welds) ❒ 8. Operators manual has been delivered to

  • Bush Hog GHM 1800, IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury. In addition to the design and configuration of equipment, hazard control and accident prevention are depen- dent upon the awareness, concern, prudence and proper training of personnel in the operation, transport, maintenance and storage of equipment. Lack of attention to safety can result in accident

  • IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-Steiger Occupational and

  • Bush Hog GHM 1800, 7 SECTION 1 INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your GHM hay mower has been carefully designed to give maximum service with minimum down time. This manual is provided to give you the necessary operating and maintenance instructions for keeping your mower in top operating condition. Please read this manual thoroughly. Understand what each control is for and how to use it. Observe all safe- ty precautions decaled on the machine and noted throughout the ma

  • SECTION II PREPARATION FOR USE TO AVOID SERIOUS INJURY OR DEATH NEVER STAND BETWEEN TRACTOR AND MOWER WHILE TRACTOR IS BEING BACKED TO HITCH. TO AVOID SERIOUS INJURY OR DEATH ADDITIONAL TRACTOR FRONT BAL- LAST MAY BE NEEDED FOR STABLE OPERATION AND TRANSPORT OF MOWER. SEE TRACTOR OPERATOR’S MANUAL FOR RECOMMENDED WEIGHTS. WARNING WARNING During mower operations, the right tracto

  • Bush Hog GHM 1800, D. Attach PTO driveline to tractor 540 rpm or 1000 rpm PTO shaft. Make certain driveline is securely connected at both ends. Attach PTO drive- line shield safety chain on both the implement and tractor ends. (Figure 2-3) CAUTION DO NOT USE A PTO SHAFT ADAPTER WITH THIS IMPLEMENT. USE OF A PTO SHAFT ADAPTER WILL VOID ALL WARRANTY CONSIDERATIONS. E. Pin parking stand in work position. (Figure 2-4) F. Adjust tractor lower lift arms so vertical main frame is perpendicular to the ground as shown in Figure 2-5. G. Set tractor 3-point hitch depth control or install the optional check

  • Bush Hog GHM 1800, SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’s manual should operate this machine. Operator should wear hard hat, safety glasses and safety shoes. The operator should read, understand and practice all safety messages shown on the caution, warning and danger decals affixed to the mower to avoid serious injury or death. It is recommended that tractor be equipped with Rollover Protective System (ROPS) and a seat belt be used. Before beginning operation, clear work area of any objects that may be picked up and thrown. Check for ditches, stumps, holes or other obstacles that could upse

  • Bush Hog GHM 1800, Breakaway pressure is regulated by the tension of the latch springs (Figure 3-3). Spring length as shipped from the factory is 4-1/8” and is satisfactory for most conditions. Breakaway pressure can be increased by turning spring retaining nuts clockwise or decreased by turning counterclockwise. DO NOT COLLAPSE SPRING TO LESS THAN 3-3/4” OR SPRING WILL BECOME SOLID BEFORE LATCH CAN TRIP. Figure 3-3 Breakaway Latch Spring 4-1/8” 3-5 OPERATION A. Perform BEFORE EACH USE maintenance listed in paragraph 4-1. B. Pin parking stand and trans

  • Bush Hog GHM 1800, 3-7 CUTTER BAR HELPER SPRING ADJUSTMENT (9’ MODELS ONLY) The 9’ models are equipped with a helper spring assembly to transfer cutter bar weight from the outer end of the cutter bar back to the frame assembly. The recommended minimum adjustment measurement is 5-1/2” from under the bolt head to the end of the rod weldment nut. (Figure 3-5) To transfer more weight, shorten the measurement. To transfer less weight, lengthen the measurement. Be advised, the shorter the measurement, the less th

  • Bush Hog GHM 1800, AFTER EACH USE 1. Clean all debris from machine. Replace any missing or illegible decals. 2. Inspect mower for worn or damaged components. Repair or replace before next use. Any replace ment components installed during repair shall include the components current safety decals specified by the manufacturer to be affixed to the component. 3. Store mower in a dry place. 4-2 LUBRICATION (Figures 4-1a, b, c, d) NOTE 8 HOURS 1. Driveline Universal Joints - Apply multi-purpose grease with grease gun. 2. Driveline Guard - Apply 2-3 shots of multipur- pose grease with grease gun to plastic fitting. 3. Cutter Bar Pivot - Apply multi-purpose grease with grea

  • Bush Hog GHM 1800, 4-3 BLADE REPLACEMENT The disc mower blades each have two cutting edges. When one edge becomes dull or damaged, remove the bolt and turn the blade over, Nuts can be re-used if not damaged. If both cutting edges of the blade have been used, the blades must be replaced. Always replace both blades on a spindle to retain balance. When replacing blades, the attaching bolt and nut should also be replaced. Use only genuine Bush Hog replacement parts. (Figure 4-2) 4-4 BELT ADJUSTMENT Belt tension should

  • Bush Hog GHM 1800, Figure 4-5 Blade Disc Cap Covering Retaining Nut Standard Crop Divider Cutter Bar The blade disc assembly is now ready to be removed from the cutter bar. If required, a steady prying force on either side of the cutter bar, spaced 180° apart, can aid in removing the blade disc assembly from the spindle shaft. C. Remove the six (6) M10 nuts connecting the spindle assembly to the cutter bar. (Figure 4-8) D. Lightly tap a screwdriver into the two slotted notches cast into each spindle housing, positioned 180° apart. Simultaneously and with equal force, press downward on the two screwdrivers. When the sealant attaching the spindle housing to the cutter bar has been broken,

  • Bush Hog GHM 1800, STANDARD CROP DIVIDER (Figure 4-6) Reattach the cap and cutter to the crop divider by reinstalling the four(4) capscrews through the top of crop divider and tightening securely. OPTIONAL CROP DIVIDER (Figure 4-7) Tilt cap sideways and insert cap assembly into the top of the crop divider. Insert pointed end of threaded rod into the center hole on the end of the round output shaft. Tighten cap by turning threaded rod clockwise so cap moves up on threaded rod until it fits tight into taper of crop divider. Tighten jam nut. Snap on hub cap. 4-7 CUTTER BAR REMOVAL A. Lower cutter bar to rest on the ground. B. Remove pin (Figure 4-9) and disconnect cylin

  • 4-9 TROUBLESHOOTING Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model num- ber, serial number, purchase date and exact cause or description of problem. Table 4-1 Troubleshooting PROBLEM PROBABLE CAUSE REMEDY Uneven

  • Bush Hog GHM 1800, Figure 4-12 Cutter Bar Arrangement and Blade Rotation NOTE The blades of adjacent oval discs must be 90° apart from one another as shown above to ensure proper timing. 9’ MAIN GEARBOX 8’ MAIN GEARBOX 7’ MAIN GEARBOX FORWARD #1 #2 #2 #2 #3 #3 #3 #4 #4 #4 #5 #5 #5 #6 #6 #7 CW CW CCW CW CCW CW CW CCW #1 #1 CCW CCW CW CCW CW CCW CW CCW CW CW 18

  • Bush Hog GHM 1800, SECTION V ASSEMBLY CAUTION THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear protective equipment such as , but not limited to, protection for eyes, ears, feet, hands, lungs and head when assembling the equipment. Do not wear loose clothing or jewelry that may catch on equipment moving parts. 2. Do not lift heavy parts or assemblies. Use crane, jack, tackle, fork t5rucks, or other mechanical devices. 3. Select an area for assembly that is clean and free of any debris which might cause persons working on the assembly to trip. 4. Arrange parts to be assembled neatly in the work area and have tools or other

  • Bush Hog GHM 1800, of front and rear curtain support. Q. Fasten transport latch to curtain support beam using a 5/8 x 1-3/4” bolt and locknut. Pin opposite end in place with faspin. R. Install curtain stop weldment flush with end of curtain support beam using one 5/8” U-bolt, lock- washer, flatwashers and nuts. Vent Plug Butt End Cylinder Elbow Figure 5-2 Hydraulic Hose Restrictor Figure 5-1 Assembly Cutter Bar Helper Spring Beam Spring Cushion Hitch Assy. Parking Stand Cylinder Curtain Transport Latch Breakaway Assy. Beam Gearbox Dirt Shield Tube Clip Curtain Support Curtain Support Beam Swath Board Curtain Stop Weldment Crop Divider Curtain Adjustment Chain Cylinder Lug 20

  • SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information. 21 82617 86

  • TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (17)

Related Products and Documents (Radio):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Jandy JS Series Installation and operation manual jandy/js-series-62L.pdf 06 Oct 2022 20
2 Platinum CCTV CD-8361 Installation manual platinum-cctv/cd-8361-991.pdf 31 Aug 2022 4
3 Compal HEL80 Operation & user’s manual compal/hel80-P27.pdf 19 Nov 2023 117
4 Panasonic OneHome BB-HCM311A Operating instructions manual panasonic/onehome-bb-hcm311a-8S9.pdf 07 Oct 2023 9 1.78 Mb
5 Tomcat 297 Rider Sweeper Operator and parts manual tomcat/297-rider-sweeper-34P.pdf 18 Oct 2022 44
6 Craftsman 351.217240 Operator's manual craftsman/351-217240-1V1.pdf 02 Nov 2022 24 2.36 Mb

Similar Resources:

  • Blaupunkt

    München RD 104

    (11 pages)
    AUTORADIO CD-AUTORADIOMünchen RD 1043 D93 653 075DSicherheitshinweiseEinbau- und AnschlußvorschriftenFür die Dauer der Montage und des Anschlusses ist der Minuspolder Batterie abzuklemmen.Beim Bohren von Löchern darauf achten, daß keine Fahrzeugteile(Batterie, Kabel, Sicherungskasten) beschädigt werden.Der Querschnitt des Pluskabels darf 2,5 mm2 nicht …
  • Kantronics

    KAM

    (68 pages)
    KAMKPC-4KPC-2400KPC-2KPC-1CommandsManualRF Data Communications Specialists1202 E. 23rd Street, Lawrence, Kansas 66046Order number (913) 842-7745Service number (913) 842-44769 am - noon, 2 pm - 5 pm Central Time, Monday-Friday …
  • Sandstrom

    S2DABB11E

    (76 pages)
    Instruction ManualDAB+ FM RadioS2DABB11E / S2DABW11EGBNOSEFIDKInstruction ManualDAB+ FM RadioInstruksjonshåndbokDAB+ FM-radioBruksanvisningDAB+ FM RadioKäyttöohjeetDAB+ FM RadioBrugsanvisningDAB+ FM RadioS2DABB11ES2DABW11E S2DABB_W11E IB_121121_Michelle.indb 1 21/11/2012 3:37 PM …
  • Motorola

    T3

    (124 pages)
    Manuel de l’utilisateur TLKR T3TLKR T3 BenutzerhandbuchManual del usuario de TLKR T3TLKR T3 – Manuale per l’utente Manual do Propriátrio TLKR T3 TLKR T3 GebruikershandleidingTLKR T3 Owner’s ManualInstrukcja obsługi radiotelefonu TLKR T3TLKR T3 Kullanıcı KılavuzuTLKR T3 Руководство владельцаTLKR_T3.book Page 1 Monday, Se …
  • Sirius Satellite Radio

    SC-FM1

    (16 pages)
    Installation Guide123456MEMOMENUDISPBANDS-SeekP-Tune+-.........ANTENNATO CONTROLLERPOWERFM OUTAUDIO OUTRLSC-FM1 Universal FM ModulatedSIRIUS Satellite Radio Tuner …
  • Audiotechnik Dietz

    BOA 85722BT

    (28 pages)
    Copyright © by Audiotechnik Dietz® Vertriebs-GmbH ● Germany Rev 0, Stand: 03 / 2012 BOA mp3 Radio mit/with Bluetooth Bedienungsanleitung Instruction Manual Audiotechnik Dietz Vertriebs-GmbH ● Benzstr. 12 ● 67269 Grünstadt ● [email protected] ● www.dietz.biz 85722BT …

Comments, Questions and Opinions: