Cabletron Systems CSMIM-T1 Quick Start Manual

Text of Cabletron Systems CSMIM-T1 User Guide:

• Cabletron Systems CSMIM-T1, Remote Annex Quick Start for Windows 1 NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LI

• Cabletron Systems CSMIM-T1, Remote Annex Quick Start for Windows 2 EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY 1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including Its documentation and media). CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABLITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE. 2. NO

• Cabletron Systems CSMIM-T1, Remote Annex Quick Start for Windows 1 PREFACE This guide is designed for quick installation of a Remote Annex in a Windows NT network environment and configuration of the Annex using Quick2Config Annex. The instructions apply to all Remote Annex models including the Remote Annex 6300. The procedures in this guide cover: ❑ Installing the software on the Windows NT server ❑ Setting up the Remote Annex ❑ Defining various network addresses ❑ Booting the Remote Annex ❑ Configuring the Remote Annex with Quick2Config and the na utilities Refer to Installing Remote Annex Network Software for Windows and the app

• Cabletron Systems CSMIM-T1, Preface 2 Remote Annex Quick Start for Windows Formats and Usage Throughout this document, the following terms may be used to refer to Cabletron Systems products or documentation. Table 1 summarizes the alternate terminology and the Cabletron product, device, or document that it refers to. Table 1: Format and Usage Printing Conventions This manual uses the following printing conventions: Alternate Form Cabletron Term Annex Communications Server Remote Annex Communications Server Remote Annex 200

• Cabletron Systems CSMIM-T1, Preface Remote Annex Quick Start for Windows 3 Related Documents Each Remote Annex hardware platform ships with the appropriate hardware guide. The remaining documentation is included with the software. [ ] In command dialogue, square brackets indicate default values. Pressing selects this value. Square brackets appearing in command syntax indicate optional arguments. { } In command syntax, braces indicate that one, and only one, of the enclosed value must be entered. | In command syntax, this character separates the different options available for a parameter. Notes give you important information. Warnings inform you about conditions

• Preface 4 Remote Annex Quick Start for Windows Getting Help If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support: Before calling Cabletron Systems Technical Support, have the following information ready: ❑ A description of th

• Cabletron Systems CSMIM-T1, Remote Annex Quick Start for Windows 1 REMOTE ANNEX QUICK START FOR WINDOWS NT Before Installing the Software Prerequisites To install Remote Annex Server Tools for Windows NT, you need: ❑ Microsoft Windows NT Server 3.51 or 4.0 configured to support the TCP/IP protocol ❑ Administrative privileges on the server ❑ 10MB free disk space on an NTFS drive ❑ One Windows NT Client 3.51 or 4.0 license per Remote Annex ❑ PC with an Intel 486 (or higher) CPU with 32 MB RAM ❑ CD-ROM drive to install the product ❑ Several formatted floppy disks for PCs without CD-ROMs Before you install the tools, you should close

• Cabletron Systems CSMIM-T1, 2 Remote Annex Quick Start for Windows The Grant To box displays the names of all groups currently allowed to log on locally. 3 Edit the list using and . ❑ To add groups or individual users, click on and select individual or group names from the Add Users and Groups window. ❑ To delete users or groups, highlight a name and click on . Software Installation Server Software Installing Remote Annex Network Software for Windows NT loads: ❑ Operating images that are downloaded to the Annex ❑ na utilities for configuring and managing the Annex ❑ Quick2Config Annex for configuring Annex ports The na util

• Cabletron Systems CSMIM-T1, Remote Annex Quick Start for Windows 3 ❑ The na and Quick2Config Annex software can be loaded on Windows NT Workstations (3.51 or 4.0) and on Windows 95 platforms. ❑ Quick2Config Annex can be installed on Windows for Workgroups 3.11 and Windows 3.1 systems. To install Quick2Config Annex on a Windows platform: 1 Put the CD-ROM into the Windows NT server’s CD drive. 2 Use the File Manager to select the CD-ROM disk. 3 Double-click on the setup.exe file. 4 Follow the dialog box instructions to select Install Software and then Quick2Config Annex. 5 When prompted for an installation directory, accept the default directory for each software module. Ref

• Cabletron Systems CSMIM-T1, 4 Remote Annex Quick Start for Windows The Remote Annex 2000 uses port 1 as its console port. The Remote Annex 539x uses the service port on the 5000 chassis as the console port. 3 Set the terminal to 9600 bps, 8 bits, 1 stop bit, no parity and no flow control. 4 For the Remote Annex 2000 or Remote Annex 4000, turn on the unit and immediately press the button on the front panel. Make sure the Test LED comes on. For the Remote Annex 539x, Remote Annex 6100 and Remote Annex 6300, turn on the unit and immediate

• Cabletron Systems CSMIM-T1, Remote Annex Quick Start for Windows 5 Select type of IP packet encapsulation (ieee802/ethernet) [<ethernet>]:: Type of IP packet encapsulation: <ethernet> monitor:: Load Broadcast y/n [y]:: All Annexes 2 If you have purchased a LAT key, enter the software key provided. monitor:: lat Enter LAT KEY: [<uninitialized>]:: Booting the Remote Annex At the Remote Annex, enter boot at the monitor prompt: monitor:: boot Enter boot file name [oper.46.enet]:: Requesting boot file "oper.46.enet". Unanswered requests shown as "?",

• 6 Remote Annex Quick Start for Windows 1 Invoke na, configure the Remote Annex to accept and process SNMP command sets, and exit na. % na command: annex 129.9.200.62 command: set annex allow_snmp_sets y command: boot command: quit 2 Click on the Quick2Config icon to open the application. 3 Choose File > Add Annex, enter the name or IP address of the Remote Annex in th

• Cabletron Systems CSMIM-T1, Remote Annex Quick Start for Windows 7 % na command: annex 192.9.200.62 command: port 6 command: set port speed 115200 command: set port control_lines modem_control command: set port input_flow_control start/stop command: set port output_flow_control start/stop command: set port type dial_in Inbound Modem command: set port mode auto_detect Outbound Modem command: set port mode slave Inbound/Outbound command: set port mode auto_adapt command: reset port 6 command: quit Serial Printer Serial printers can be connected to any Annex serial port. In this example the printer is connected to

• 8 Remote Annex Quick Start for Windows Dataproducts Interface Set the printer type using na and send data to the printer using aprint: % na command: annex 192.9.200.62 command: printer 2 command: set printer type dataproducts command: reset printer command: quit % aprint -A 192.9.200.62 -p2 [filename] Configuring Security By default, the Annex allows unrestricted access. If y

More Instructions:

	Cabletron Systems CSMIM-T1 Administrator's manual 04-03-2023 418	DOWNLOAD
	Cabletron Systems CSMIM-T1 Installation manual 17-03-2024 198	DOWNLOAD

Related Products and Documents (Modem):

Comparable Devices:

Similar Resources:

• Alcatel Modem (15 pages) 1 User Manual Table of Contents 1. Safety and Use ....................................................................... 2 2. Installation Guide .................................................................. 3 3. Main Interface Overview ....................................................... 4 4. Connect to Internet .................................. …

• Siemens SIMATIC (112 pages) SIMATICSIMATIC TOP connectSystem cabling for S7-300Manual09/201870327045899PrefaceSafety notes1Documentation guide2Product overview3Connecting4Wiring SIMATIC TOP connect to the I/O modules5Technical specifications6Environment7Dimension drawingsACircuit diagramsBSpare parts / AccessoriesCService and SupportD …

• Weidmuller WI-MOD-400-E (113 pages) Weidmuller Wireless Ethernet Modem and Device Server User Manual 1 Rev Version 1.1 Industrial Wireless Ethernet Modem and Device Server User Manual WI-MOD-400-E & WI-MOD-950-E Version 1.1 July 2015 Read and Retain for Future Reference …

• Spectrum Digital TMS320C5515 eZdsp (9 pages) 512846-0001 Rev A TMS320C5515 eZdsp Stick Quick Start Guide1.0 SYSTEM REQUIREMENTSTo operate the Spectrum Digital XDS100 JTAG Emulator with your system it needs to meetthe following requirements:• 2 GB of free hard disk space • Microsoft WindowsTM XP/Vista• Min 1 GB ram …

• More BYO (3 pages) Step 1. Locate the telephone wall socket in your property that has been activated for NBN. Please note that there may be multiple telephone wall sockets in your property. Step 2. Disconnect all equipment from your telephone sockets. This includes phones and fax machines plugged in around the property. These devices will interfere with the NBN signa …

• SMC Networks SMC EZ Connect SMC70032AE (14 pages) Quick Install GuideSMC70032AEEZ Connect™ADSL Ethernet Modem• Supports both G.DMT and G.lite• Interoperable with most major DSLAMs• Always-on digital connection• Bridging and routing functions• Management: SNMP, MIB II, Telnet, GUI …

Comments, Questions and Opinions: