Manualios.com

Compaq 5525B/31/32 Operation & User’s Manual

Compaq 5525B/31/32 Manual Online:

3.85, 1822 votes
Compaq 5525B/31/32 User Manual
Compaq 5525B/31/32 User Guide
Compaq 5525B/31/32 Online Manual

Text of Compaq 5525B/31/32 User Guide:

  • Compaq 5525B/31/32, Example 97 The last part (“More”) of the screen is: Notice the entries for Connection type and Destination type (required). Since we chose to autostart one writer when the queue was formed, we should have a writer started by the name of IP_P5000. The command WRKWTR WTR(*ALL) may be used to see status of Remote writers (the WTR(*all) is required to see remote writers). The command to start our example remote writer is STRRMTWTR IP_P5000. The ENDWTR command works as usual. At this point test the results by doing a print screen, and ensure that the output is as desired. If problems occur, be sure the correct data type is being used (no AFP™ or IPDS™)

  • Compaq 5525B/31/32, Direct Socket Printing 61 3. Log in as “root”. 4. At the password prompt, press ENTER since there is no default password. 5. Change to the dest directory. Syntax: cd dest 6. List the contents of this directory using the “dir” command and determine which destination/queue you would like to send the print job through. Most likely you will select “ d1prn” for the PRN port. 7. Change to this destination directory. Example: cd d1prn 8. Change the mode to correspond with the type of file you are going to print. By default, ASCII is set for text-only files but if you need to print both text and graphics,

  • Compaq 5525B/31/32, Chapter 4 Unix Troubleshooting Tips 66 3. On the PrintNet, place SWITCH 2, the center switch, in the down position. 4. Power on the printer and wait for the READY state. 5. On the PrintNet, place SWITCH 2, the center switch, in the up position. 6. From a workstation attached to this network segment, create an ARP entry. The PrintNet IP address and hardware or MAC address are needed. At the workstation enter: arp -s < ipaddress > < MACaddress > ping < ipaddress > 7. Try to “ ping ” this I

  • Compaq 5525B/31/32, Chapter 3 Windows Troubleshooting Tips 48 • Are you logged in as the “Administrator”? This installation requires administrator privileges. • “LPR port” is not listed in step 5. Cancel the installation and install Microsoft TCP/IP printing service on the server. • LPR configuration warning during step 6. The ethernet cable is not plugged in, or printer is not turned on. This message is a communication failure between the NT server and the PrintNet card. Check cabling, IP address settings, gateway, etc. • Test page does not print or prints garbage. 1. Is the printer online? Re-sen

  • Chapter 4 Unix Troubleshooting Tips 64 Stair-Stepped Output Stair-stepped output is print which starts at the top left of the page but every line thereafter starts a little further over to the right. It also refers to Unix jobs that print one line of text at the top of a page followed by a series of blank pages. This kind of output happens only with Unix text jobs if carr

  • Compaq 5525B/31/32, Chapter 4 Unix PrintNet Configuration 56 Using BOOTP BOOTP allows you to dynamically assign an IP address to the PrintNet upon bootup. In addition, the BOOTP server can provide additional details like a default router/gateway address. To configure the PrintNet with its TCP/IP settings using BOOTP: 1. On your BOOTP server, make an entry in the /etc/bootptab file for the PrintNet. Syntax: PrintNetIPname :\ :sm= netmask :\ :hd= homedirectory :\ :bf=null:\ :gw= defaultgateway :\ :ht=ethernet:\ :ha= ethernetaddress :\ :ip= ipaddress :\ :ts= timeserver :\ :to= timezone : Example: spike:\ :sm=255.255.255.0:\ :hd=/usr/null:\ :bf=null:\ :gw=192.75.11.1:\ :ht=ethernet:\ :ha=00

  • Compaq 5525B/31/32, Using HTML Forms 69 Using HTML Forms When defining a new print queue on a Novell file server, a new print server must be defined to represent the PrintNet. This name must match the pre-defined name given to the print server. By default, this name is in the format “M_ xxxxxx ” where “ xxxxxx ” equals the last six digits of the PrintNet Ethernet address found on a configuration printout or control panel settings under Ethernet parameters, MAC Address (e.g. M_071C1A). To use the HTML forms to define a print

  • Optional 23 Optional Additional settings, like routing entries, can be configured. This allows communications across subnets. Configuration of the PrintNet can be done from the printer control panel, IPAssign, Web browser, or host commands. Configuration Using the Control Panel You can set any of three listed parameters from the printer control panel. Th

  • Chapter 3 Windows Host Configuration 38 9. Determine if the printer is shared with other network users. If it is shared, the share name and the operating system must be selected. 10. Print a Windows test page. 11. If there are any problems during or after installation, see “Windows NT 4.0 Host Setup Problems” on page 47.

  • Compaq 5525B/31/32, Chapter 6 OS/2 Workstation Configuration 88 9. At the system prompt, enter: store tcpip from default config http on reset NOTE: This will reset all TCP/IP settings to factory default and reset the PrintNet. 10. Power the printer off and then back on. 11. Set the IP address, subnet mask, and default gateway parameters to the desired values. 12. If Web browser access does not work, Telnet into the PrintNet as root. Enter the following command: config http on If you are still experiencing difficulty accessing or browsing the printer, contact technical support for further assistance.

  • Compaq 5525B/31/32, Chapter 3 Windows PrintNet Configuration 26 13. If you want to store the TCP/IP settings into the PrintNet flash memory via a browser, click on LAUNCH BROWSER at the next window that displays. This will prevent you from losing the settings after a power cycle. If not, click “No.” 14. Read the text in the “Configuration Information” window that displays and click OK to launch your Web browser. NOTE: If you are returned to the IPAssign main dialogue box, you will be unable to launch your browser this way. Please load it ma

  • Compaq 5525B/31/32, Chapter 8 Complete Command List 106 set dest destination name newname set dest d1prn name laser Change the current name of the destination to a new name as indicated by newname . This newname must be nine characters or less or it will be truncated. These names are case sensitive. set dest destination backchannel prn [prn] set dest d1prn backchannel prn Establish a return path for printer feedback for a given destination . Since the PrintNet I/O port is bi-directional, however, you will most likely use the same I/O port that the destination is currently sending jobs to. set dest destination model modelname set dest d1prn model m4 Associate a model w

  • Compaq 5525B/31/32, 81 6 OS/2 Configuration Overview This chapter details a complete OS/2 configuration setup including: 1. Configuring the PrintNet Interface with its TCP/IP settings 2. Configuring a new printer on an OS/2 workstation. The procedure given will be from an OS/2 Warp 4 system, but the setup is similar to OS/2 Warp 3 and v2.11. 3. OS/2 must have TCP/IP installed on it and be configured with the correct IP parameters. See OS/2 documentation/help and your network administrator. Configuring the PrintNet Interfa

  • Chapter 8 Complete Command List 112 set sysinfo descramblekey hexvalue set sysinfo descramblekey 1234 Set the key value used for descrambling print jobs that have passed through Printronix npscramble utility on a TCP/IP host. This key is a four-digit hexadecimal value obtained from the host software, npscramble. Within the npscramble source code, there is a vari

  • Operating Modes 13 Operating Modes The PrintNet has a self test and internally controlled modes. These are: Power-on Self Test The power-on self test performs diagnostic tests on the PrintNet processor, RAM, ROM, EEPROM, parallel ports, and network interface. The STAT, ERR, and NET LEDs indicate which test is currently in progress. Table 1. LED Pattern Indications STAT ERR NET Mode

  • Compaq 5525B/31/32, 21 3 Windows Configuration Overview This chapter details a complete Windows configuration setup including: 1. Identifying the PrintNet on the network using TCP/IP as the underlying protocol 2. Configuring the PrintNet with its mandatory TCP/IP settings (IP address and subnet mask) 3. Configuring a new printer on the Windows station Windows Environment Description The PrintNet supports network printing under Windows environments by using TCP/IP. In a Windows NT  setup, pure TCP/IP is used as the network protocol whereas with Windows 95  , NetBIOS over TCP/IP is used. Figure 6 shows two of the most common Windows setups you will see

  • Compaq 5525B/31/32, Chapter 2 Configuration Tools 18 HTML Forms The PrintNet settings can be configured over TCP/IP through a standard Web browser. The PrintNet Web pages provide a handy way to access some of the commands built in to the print server. NOTE: If a router is used, make sure a gateway value is configured. To access the PrintNet home page: 1. Make sure the print server has an IP address and subnet mask so it is recognizable on your TCP/IP network. 2. Make sure your network station can successfully “ ping” the PrintNet over the network.

  • Compaq 5525B/31/32, set Commands 111 set sysinfo loginfo [-]sys | [-]tcp | [-]ipx | [-]spx set sysinfo loginfo -sys ipx Set the PrintNet debugging information type. Usually this information includes unexpected errors or exceptions from the print server divided into these groups: sys General system messages. tcp TCP stack messages. ipx IPX stack messages. spx SPX stack messages. NOTE: This is not printer or job logging information. set sysinfo logport null|syslog set sysinfo logport null Define where the debugging information should be sent to. This can be sent to an output device off of the PrintNet I/O port or to a central TCP/IP host running a SYS

  • Compaq 5525B/31/32, Chapter 9 PrintNet Security 120 Example: set user passwd root your_password_for_root save 2. Direct your Web browser to URL “ http:// PrintNetIPaddress /adminConf.html” (e.g. “ http://192.75.11.9/adminConf.html”). NOTE: If prompted for a “User ID” and password first, type in “ root” for the user ID and press ENTER at the password prompt since there is no password by default. 3. At the “Administration Configuration” HTML form that displays, scroll down to the “Passwords” section. 4. Click within the “Old” field beside the “Root Password” heading and enter the existing root password. By default, t

  • Compaq 5525B/31/32, PrintNet Will Not Talk on the Network 43 PrintNet Will Not Talk on the Network • Have you assigned the PrintNet a unique and valid IP address which corresponds with the other IP addresses on your network? For example, are you sure no other device is using this IP address? • Are you sure you are trying to talk to the PrintNet from a Windows station on the same subnet? Currently, the print server can only be seen locally unless you configured a routing entry earlier. • If you look at the back of the printer, is the STAT LED flashing once a

  • Compaq 5525B/31/32, Chapter 7 AS/400 Configuration 96 8. Create an Output Queue using the WSCST Object, and printer destination “d1prn”. In this example the Output Queue is named “IP_P5000”. Notice that the entry for “Remote printer queue” refers to the “queue”, or destination name in the PrintNet, and that we will autostart one Writer. This Writer is a “Remote Writer” since it is networked. Create Output Queue (CRTOUTQ) Type choices, press Enter. Output queue. . . . . . . . . . . . . . . . . .

  • Compaq 5525B/31/32, Chapter 2 Configuration Tools 20 Configuration Alternatives Besides the HTML forms and software provided, the PrintNet internal command shell, npsh, can also be reached using these methods: Telnet A TCP/IP command that helps configure PrintNet settings remotely. A TCP/IP host starts a Telnet session with the print server and logs in to the device command shell to alter and view settings. Example: telnet 192.75.11.9 Remote Shell A TCP/IP command that helps configure print server settings remotely. A TCP/IP host uses this command to remotely execute a single command on the PrintNet. Example: rsh spike list prn This command remotely executes the npsh comma

  • Compaq 5525B/31/32, Configuration Using IP Assign 25 8. At the “IPAssign” main dialogue box that appears, you should see an entry for your PrintNet appear in the list box. Figure 7 shows an example screen. Figure 7. IPAssign Main Screen 9. Once your PrintNet Ethernet Address appears in the list box, select it and click on ASSIGN. 10. At the “Assign IP” dialogue box that displays next, fill in the IP address and subnet mask for this PrintNet. NOTE: You can also assign a default router/gateway entry within this dialogue box allowing your PrintNet to communicate across subnets. This is optional. 11. Cl

  • Compaq 5525B/31/32, Web Browser/HTTP Problem 47 Web Browser/HTTP Problem In some cases you may not be able to browse the printer web page simply because the PrintNet HTTP may be turned off. If you can not “ ping ” the PrintNet IP address, make sure the IP Address, subnet mask, and default gateway are set correctly by checking the Ethernet Parameters menu from the operator panel. See the User’s Manual for configuration menu information. If you can “ ping ” the PrintNet IP address but can not access the web pages, perform the following procedure to verify the PrintNet HTTP is turned on. 1. Telnet into the PrintNet and log in as root with no password. 2. At the system prompt enter the follow

Related Products and Documents (Printer):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 MATLAB SIMHYDRAULICS 1 Operation & user’s manual matlab/simhydraulics-1-7PZ.pdf 28 Jan 2024 71
2 Kawai ES7 Owner's manual kawai/es7-XM8.pdf 09 Apr 2023 140
3 Binary B-300-HDMATRIX-4x4 Owner's manual binary/b-300-hdmatrix-4x4-CBB.pdf 07 Feb 2023 21
4 Philips CCB193AT99 Owner's manual philips/ccb193at99-7SK.pdf 29 Oct 2023 60
5 Philips 21PT5401 Manual  philips/21pt5401-7AG.pdf 25 Dec 2022 52 1.33 Mb
6 Milwaukee M12 Operator's manual milwaukee/m12-X57.pdf 28 Feb 2023 36

Similar Resources:

  • Epson

    TM-P80

    (154 pages)
    Describes how to control the printer and necessary informationwhen you develop applications.Describes setup and installation of the product.Describes how to handle the product.Describes general specifications, initial software settings, and character code tables.Describes features of the product.Technical Reference GuideM00067303Rev. C Product Overview Set …
  • Canon

    COLOR BUBBLE JET PRINTER I450

    (2 pages)
    Advanced printer technology at an exceptional value.The Canon i450 Color Bubble Jet Printer delivers high-quality photos, detailed printing from the Web, crisp text and exclusiveCanon features—all at a great value. It achieves print speeds of up to 18 ppm in black and up to 12 ppm in color along withresolution of up to 4800 x 1200 color dpi.* Canon advance …
  • HP

    Pro 3400

    (13 pages)
    1.(1) external 5.25" drive bay6.(3) PCIe x1 slots, (1) PCIe x16 slot, (1) miniPCIe slot2.300 Watt Power Supply7.USB Scroll Mouse3.Rear I/O includes: (4) USB 2.0 ports, RJ-45 Ethernet Port, DVI-Dand VGA video Ports, microphone jack, audio in/out jacks (5.1channel audio out)8.HP USB Standard Value Keyboard4.Front I/O includes: (2) USB 2.0 ports, dedicate …
  • Epson

    PowerLite W6

    (2 pages)
    • Rich, full-time color —3-chipopticalengine• Reliable performance —3LCDtechnology• Ideal for widescreen computers and movies —nativeWXGAresolution(16:10)• Super bright and colorful —2000lumenscolor,2000lumenswhitelightoutput• Easy picture adjustment —automatickeys …
  • HP

    Compaq Presario,Presario CQ5110F

    (219 pages)
    bMaintenance and Service GuideCompaq Evo Notebook N1020v Series Compaq Evo Notebook N1000v Series Compaq Presario 1500 Series Mobile PCDocument Part Number: 279372-002November 2002This guide is a troubleshooting reference used for maintaining and servicing the notebook. It provides comprehensive information on identifying computer features, components, and s …
  • Durst

    Rho 161 TS

    (4 pages)
    Rho 161 TSRoll to Roll UV Inkjet-Printer for Traffic Sign Applications Durst introduces the new, compact high speed direct digital UV printing system for long-lasting traffic sign production, designed for manufacturers of traffic signs. The Rho 161 TS is a further development of the Rho 160R printer and is escpecially developed for printing directly onto …

Comments, Questions and Opinions: