Manualios.com

Compaq Pro UPS 500 Operation And Reference Manual

Compaq Pro UPS 500 Manual Online:

3.05, 948 votes
Compaq Pro UPS 500 User Manual
Compaq Pro UPS 500 User Guide
Compaq Pro UPS 500 Online Manual

Text of Compaq Pro UPS 500 User Guide:

  • Compaq Pro UPS 500, Operation 3-5 “ON” Mode ■ Function: ENABLES battery backup. ■ UPS Conditions: The UPS battery is charging. Power is ON at the UPS receptacles. The green LINE STATUS indicator ( ) is illuminated. ■ Setting Advantages: Provides battery backup in the event of a blackout or brownout. “STANDBY” Mode ■ Function: DISABLES battery backup. ■ UPS Conditions: The UPS battery is charging. Power is ON at the UPS receptacles. The green LINE STATUS indicator ( ) is flashing. The UPS audio alarm is sounding once per minute. ■ Setting Advantages: Continues to charge

  • Compaq Pro UPS 500, 1-4 Compaq Pro UPS 500 Operation and Reference Guide Rear Panels The Compaq Pro UPS 500 models feature the following rear panel configurations: 2 5 6 4 3 1 Figure 1-2. Rear panel configuration - 100VA and 120VA models Communications port Battery compartment Noise and surge-protected receptacles Battery, noise, and surge-protected receptacles Non-detachable input power cord with NEMA 5-15 plug RJ11 Phone/Fax Surge Protectors

  • Compaq Pro UPS 500, Index 3 connecting the Phone/Fax Surge Protector 2-5 requirements hardware 2-2 software 2-2 tools 2-2 starting the UPS 2-7 L LINE STATUS indicator 3-10 load calculating total load (VA) 2-6 overload 2-6 M mode of operation Automatic Shutdown mode 3-5 Automatic Voltage Regulation (Boost mode) 3-6 Battery Operate mode 3-5 ON mode 3-5 STANDBY mode 3-5 O ON BATTERY indicator 3-10 Battery Operate mode 3-5 illuminated 3-5 ON mode 3-5 Operating mode selecting 3-3 operating the UPS BATTERY LOW/ALARM indicator illuminated 3-5 ON BATTERY

  • Compaq Pro UPS 500, Introduction 1-7 For example, if the software detects an extended utility power blackout, the program will initiate messaging across the system and will start an operating system shutdown. For more information on using the Compaq Power Manager Pro UPS software, see Chapter 4, “Software.” NOTE: Select Compaq NeoServers have UPS power management software preinstalled. Some NeoServer customers may not need to install Compaq Power Manager Pro UPS software. Please see the NeoServer documentation included with the NeoServer unit for specific power managem

  • Compaq Pro UPS 500, Appendix A Regulatory Compliance Notices Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules. These rules place computers and related peripheral devices into two classes, A and B, depending upon their intended installation. Class A devices are those that may reasonably be expected to be in

  • Compaq Pro UPS 500, Introduction 1-5 5 4 3 1 2 Figure 1-3. Rear panel configuration - 230VA model Communications port Battery compartment Noise and surge-protected receptacle Battery, noise, and surge-protected receptacles IEC-320 power inlet

  • Compaq Pro UPS 500, 2-8 Compaq Pro UPS 500 Operation and Reference Guide Connecting Devices to the Battery-and-Surge-Protected Receptacles Plug the equipment that needs battery backup support in the event of a blackout (such as the computer, monitor, and external modem) into the Battery-and-Surge-Protected receptacles ( ) on the UPS rear panel. The 100VA/120VA (left) and 230VA (right) models are illustrated below. 1 1 Figure 2-3. Connecting devices to the Battery-and-Surge-Protected receptacles ( )

  • Compaq Pro UPS 500, 3-14 Compaq Pro UPS 500 Operation and Reference Guide RJ11 Phone/Fax Surge Protector Select Compaq Pro UPS 500 models include a Phone/Fax Surge Protector to safeguard communications equipment (such as a fax machine or a modem) from spikes and surges from transients present on telephone lines. Communications Port The communications port connects the UPS to any computer or workstation. Use the communications port with Compaq Power Manager Pro UPS software to enable automatic shutdown and power management functionality. Surge-Protected Receptacle(s) These receptacles provide connected equipment with AC line power during normal operation. They also safeguard equipment against damaging sur

  • Compaq Pro UPS 500, About This Guide viii Getting Help If you have a problem and have exhausted the information in this guide, you can get further information and other help in the following locations. Compaq Technical Support In North America, call the Compaq Technical Phone Support Center at 1-800-OK-COMPAQ (1-800-652-6672) 1 . This service is available 24 hours a day, 7 days a week. Outside North America, call the nearest Compaq Technical Support Phone Center. Telephone numbers for world wide Technical Support Centers are listed on the Compaq website. Access the Compaq website at: http://www.compaq.com. Be sure to have the following information available before calling Compaq: ■ Techni

  • Compaq Pro UPS 500, 1-2 Compaq Pro UPS 500 Operation and Reference Guide Compaq Pro UPS 500 Models The Compaq Pro UPS 500 includes the following models and part numbers: Table 1-1 Compaq Pro UPS 500 Model Descriptions UPS Model UPS Kit Part Number Comments 500 136386-001 120VA; North America; Tower 500 136386-291 100VA; Japan; Tower 500 136386-B31 230VA; International; Tower Table 1-2 Compaq Pro UPS 500 Model – Additional Part Information UPS Model Spare Parts Kit Number RJ11 Phone/Fax Surge Protector Cable Part Number 500 155373-1 112666-010 500 155373-291 112666-010 500 155373-2 Not Applicable

  • Compaq Pro UPS 500, 3-2 Compaq Pro UPS 500 Operation and Reference Guide Operation Precautions Observe these precautions when using the UPS. WARNING: To reduce the risk of personal injury from earth conductor leakage current: ■ Do not operate a UPS that is disconnected from the utility power source. ■ Disconnect protected devices from the UPS before disconnecting the UPS from utility power. ■ Use the TEST/ALARM RESET button to test the battery rather than unplugging the UPS. For more information, see “Initiating a UPS Self-

  • Compaq Pro UPS 500, 3-8 Compaq Pro UPS 500 Operation and Reference Guide TEST/ALARM RESET Button The TEST/ALARM RESET button ( ) is a momentary switch that allows you to initiate a UPS self-test or silence an audio alarm. Initiating a UPS Self-Test 2 31 Figure 3-4. Initiating a UPS self-test BATTERY LOW/REPLACE indicato r UPS LOAD indicato r TEST/ALARM RESET button In the ON mode, pressing and holding the TEST/ALARM RESET button ( ) (until the UPS acknowledges with a beep) will initiate a self-test of the UPS battery, full function of the backup system, and the load condition of the Battery-and-Surge-Protected receptacles. During

  • Compaq Pro UPS 500, Introduction 1-3 Front Panels The Compaq Pro UPS 500 models feature the following front panel configuration: 5 62 3 41 Figure 1-1. Front panel configuration Symbol ON/STANDBY button LINE STATUS indicator ON BATTERY indicator BATTERY LOW/REPLACE indicator UPS LOAD indicator TEST/ALARM RESET button

  • Compaq Pro UPS 500, Operation 3-7 WARNING: To reduce the risk of personal injury resulting from electric shock or to avoid damage to the equipment: ■ Plug the input line cord into a grounded (earthed) electrical outlet that is installed near the equipment and is easily accessible. ■ Do not disable the grounding plug on the input line cord. The grounding plug is an important safety feature. ■ Do not use an extension cord. IMPORTANT: ■ Performing a UPS Start-On-Battery with load present requires more power than keeping an already-operating load running. You may not be able to start as large a load as usual when performing a UPS Start-On-Battery using the

  • Compaq Pro UPS 500, vii Compaq Pro UPS 500 Operation and Reference Guide Symbols in Text These symbols may be found in the text of this guide. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. IMPORTANT: Text set off in this manner presents clarifying information or specific instructions. NOTE: Text set off in this manner presen

  • Software 4-3 UPS Control Functions Perform the following UPS control functions, using the software security features to: ■ Protect access. ■ Execute a UPS self-test. ■ Shut down the operating system and UPS. Configuration Parameters System administrators and operators can configure Compaq Power Manager Pro UPS software parameters through the web-based int

  • 3-6 Compaq Pro UPS 500 Operation and Reference Guide ■ Automatic Voltage Regulation (Boost) Mode: When an undervoltage occurs, the UPS will automatically correct the voltage level without switching to battery power. When this occurs, the UPS may emit a clicking sound. The more the UPS adjusts the voltage level, the more the UPS will click. This is a normal, auto

  • Compaq Pro UPS 500, About This Guide This guide is designed to be used as step-by-step instructions for installation and as a reference for operation, troubleshooting, and future upgrades. Text Conventions This document uses the following conventions to distinguish elements of text: Keys Keys appear in boldface. A plus sign (+) between two keys indicates that they should be pressed simultaneously. USER INPUT User input appears in a different typeface and in uppercase. FILENAMES File names appear in uppercase italics. Menu Options, Command Names, Dialog Box Names These elements appear in initial capital letters. COMMANDS, DIRECTORY NAMES, and DRIVE NAMES These elements appear in uppercase. Type Whe

  • Compaq Pro UPS 500, 3-10 Compaq Pro UPS 500 Operation and Reference Guide Front Panel Indicators and Audio Alarms The front panel indicators signal the status of the UPS. LINE STATUS Indicator (Green) The LINE STATUS indicator illuminates whenever the UPS is connected to acceptable AC utility line power. While the UPS is in the ON mode, the LINE STATUS indicator will remain constantly illuminated to indicate that battery backup is enabled and will be available at the Battery-and-Surge-Protected receptacles in the event of a blackout or brownout. While the UPS is in the STANDBY mode, this indicator will flash (and an alarm will sound

  • Battery Maintenance 5-3 When to Replace the Battery If the BATTERY LOW/REPLACE indicator ( ) illuminates during a self-test, the UPS may require service. The indicator will be accompanied by an audio alarm. 1 Figure 5-1. BATTERY LOW/REPLACE indicator ( ) Verify that battery replacement is required by allowing the UPS to charge the battery for 12 hours, then initiate a confirming self-test.

  • Compaq Pro UPS 500, Software 4-5 Installation Wizard Notification Compaq Power Manager Pro UPS software takes advantage of the Microsoft AutoPlay feature. To install Compaq Power Manager Pro UPS software using this Install Wizard, follow the steps below: 1. The Compaq Power Manager Pro UPS software Select Language screen is displayed when the CD-ROM is inserted into the drive. Select the desired language. Figure 4-1. Select Language Screen

  • Compaq Pro UPS 500, Installation 2-9 Connecting Devices to the Surge-Protected Receptacle(s) Plug non-critical equipment into the Surge-Protected receptacle(s) on the UPS rear panel, as illustrated in the following figure. The Surge-Protected receptacle(s) ( ) will provide connected peripherals with surge protection without committing valuable battery power to support the peripherals during blackouts. The 100VA/120VA (left) and 230VA (right) models are illustrated below. 2 2 Figure 2-4. Connecting devices to the Surge-Protected receptacles ( ) NOTE: When the UPS is con

Related Products and Documents (UPS):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 SMITH SYSTEM Lift Desk Assembly instructions manual smith-system/lift-desk-M49.pdf 10 Jan 2024 8
2 Philips CED1910BT Operation & user’s manual philips/ced1910bt-D51.pdf 28 Aug 2023 45 4.76 Mb
3 YASKAWA NX100 Instruction manual yaskawa/nx100-768.pdf 04 Jul 2023 88
4 REVELL Concerta C10 Owner's manual revell/concerta-c10-NBZ.pdf 22 Aug 2023 9 0.27 Mb
5 AMD 7ZXR Manual  amd/7zxr-Q2Z.pdf 16 Jul 2022 119 1.83 Mb
6 Watec WAT-704R Operation manual watec/wat-704r-X1V.pdf 30 Sep 2023 1

Similar Resources:

  • Keatec Energy

    RTM Series

    (19 pages)
    Keatec RTM Series Modular Online UPS 208V/120Vac 2PH 2PH Rack AssemblyVersion: 2017-05-15User GuideUNLESS SPECIFICALLY AGREED TO IN WRITING, SELLER(A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION;(B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DA …
  • CyberPower

    BR850ELCD

    (2 pages)
    BR650ELCD / BR850ELCD / BR1000ELCD / BR1200ELCD User’s Manual K01-C0000110-00 This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thorou …
  • Omron

    Powli BU50SW

    (74 pages)
    • This manual provides important safety-related information. Thoroughly read and understand this manual before installing and using the product. • Keep this manual in a convenient location so that you can refer to it whenever necessary.Uninterruptible Power Supply (UPS)Instruction ManualBU50SW/BU75SW/BU100SW/BU150SW-バッテリ 交換バッテリ  …
  • Power Walker

    VI 1000RT LCD

    (75 pages)
    EN Line Interactive UPS PowerWalker VI 1000RT LCD PowerWalker VI 1500RT LCD PowerWalker VI 2000RT LCD PowerWalker VI 3000RT LCD Manual EN, DE …
  • CyberPower

    OL6KERT3UDPM

    (25 pages)
    User’s Manual OL6000ERT3UD OL8000ERT3UD OL10000ERT3UD OL6KERT3UDPM OL8KERT3UDPM OL10KERT3UDPM Cyber Power Systems Inc. www.cyberpower.com K01-0000424-03 …
  • GE

    300

    (4 pages)
    GuardSwitch™ Series 300341-BT341-BT-06(J)(K)341-BT-12(J)(K)341-BT-20K341-BT-25J341-B3T-06J341-B3T-12J341-B3T-20J341-B3T-25JSafety Interlock SwitchInstallationUse non-removable screws, bolts, or nuts to mount the switch and actuator. Do notover-torque mounting hardware.1. Position the switch and actuator so the labels are reading in the same direction(See F …

Comments, Questions and Opinions: