Casio DT-X30 Series Operation & User’s Manual

Text of Casio DT-X30 Series User Guide:

• Casio DT-X30 Series, E-17 F7: Lowers sound volume. F8: Not assigned. Fn + F8: Selects text entry mode. (The mode changes in order of Numeric ➝ Uppercase letter ➝ Lowercase letter.) 14 Hand Belt Holes Used to attach the hand belt. 15 L Trigger Key Used to perform bar code reading. 16 R Trigger Key Used to perform bar code reading. 17 IR Port Used for communication with another Handheld Terminal. 18 Barcode Reader Port Laser light or LED light is emitted from this window that reads bar codes. 19 Stylus Holder Holds the stylus. 20 Reset Switch Used to reset the Handheld Terminal. 21 Camera Lens (Came

• E-11 L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Exposure to radio frequency radiation The insta

• E-47 Do not subject the Handheld Terminal and Ethernet Cradle to vibration or impact during communication. This can cause communication to be interrupted. When placing the DT-X30 into the cradle, make sure that it is seated properly and that the power LED at the front of the Ethernet Cradle is lit in green. Charging and communication will not proceed properly if the Handheld Terminal is n

• Casio DT-X30 Series, E-50 Using the Car Mounted-type Battery Charger (HA-G35CHG) The optionally available Car Mounted-type Battery Charger (HA-G35CHG) can be used to charge the battery installed in the Handheld Terminal using power from the cigarette lighter in your car. General Guide Top 4 Left 2 Front 2 2 3 5 Back 1 2 1 AC Adaptor Jack Connect the Car Power Cable (bundled) here. 2 Removal Buttons Press when removing the DT-X30. 3 Terminal Detect Switch This switch detects when the DT-X30 is mounted correctly on the charger. 4 Power Contacts Power is supplied to the DT-X30 via these contacts. 5 Power LED This LED indicates the power status and the moun

• Casio DT-X30 Series, E-40 GPS (DT-X30GR-10/GR-10C/GR-30/GR-30C/GR-15/GR-15C/GR-35/GR-35C/G-35U/G-35UC): General specifi cations: 16-channel receiver, L1 1575.42 MHz, C/A code Protocol: NMEA-0183 Sensitivity: Acquisition sensitivity: -141 dBm Tracking sensitivity: -158 dBm SIM card: Standard: ISO 7816 IC Card standard General specifi cations: Support for 3 V and 1.8 V SIM cards Camera (DT-X30GR-10C/GR-30C/GR-15C/GR-35C/G-35UC): Approx. 2,000,000 pixels Autofocus function Power Requirements: Power Source: HA-G20BAT Battery Pack Memory Backup: Rechargeabl

• Casio DT-X30 Series, E-8 Backup Copies of All Important Data Caution Note that CASIO Computer Co., Ltd. shall not be held liable to you or any third party for any damages or loss caused by deletion or corruption of data due to use of the Handheld Terminal, malfunction or repair of the Handheld Terminal or its peripherals, or due to the batteries going dead. The Handheld Terminal employs electronic memory to store data, which means that memory contents can be corrupted or deleted if power is interrupted due to the batteries going dead or incorrect battery replacement procedures. Data cannot be recovered once it is lost or corrupted. Be sure to make backup copies of all important data. One way to d

• Casio DT-X30 Series, E-29 4. Tap the [Calibration] button. The display appears as shown at right. 5. Press the Trigger Key to emit laser light, and align the light with the barcode for adjusting emission width. Align the laser light with the narrow bars on both sides. The message appears as shown at right when adjustment is completed. Repeat the setting if “Setting failed” message appears. Emission Width Adjustment Bar code x x x

• Casio DT-X30 Series, E-26 Using the C-MOS Imager (Imager Models) 1. Turn on the Handheld Terminal, position its C-MOS Imager reader port near the bar code or 2D code, and then press the Trigger Key. 2. The Handheld Terminal reads the code by emitting laser and red lights. Indicator 2 (read operation indicator lamp) lights in green when the reading is successful. Bar code and stacked 2D code Reading Guide When you press the Trigger key, LEDs in the Handheld Terminal emit laser and red lights. Align the laser frame with the center of the bar code or 2D code you are trying to read. Take particular care aligning the light when t

• Casio DT-X30 Series, E-53 1 Charge Indicator LED This LED indicates the charge status of the battery pack(s). Off: Not charging Red: Charging Red Flashing: Battery pack problem Green Flashing: Standby Green: Charging complete 2 Power Contacts Power is supplied to the Handheld Terminal via these contacts. 3 AC Adaptor Jack This is used to supply power by connecting the AC adaptor (sold separately). 4 Dual Battery Charger Connection Port Use this port to connect multiple Dual Battery Chargers to each other. 5 Connection Bracket Attachment Holes The connection bracket attaches here when you connect multiple Dual Battery Chargers to each other. Important! Allowing the power contacts become wet can cause a

• Casio DT-X30 Series, E-32 GSM Communication To use the GSM functions, you must receive service from a wireless service provider. Available GSM functions may be dependent on the service provider to which you connect. Please consult your service provider for details about network service. If you use GSM and WLAN at the same time, the communication speed of WLAN may be reduced, or the reception of WLAN signals may be disconnected, due to the operational state of GSM. GPS When you use the Handheld Terminal for the fi rst time or after an extended period of no use, it may take a long time before the Handheld Terminal determines its positioning. In such a case, operate the GPS mode where there are no ob

• Casio DT-X30 Series, E-56 Using Rechargeable Battery Pack HA-G20BAT Important! Store a battery pack in its special soft case whenever you are not using it. If the battery pack has been left over unused for a long period of time, the capacity remained decreases due to spontaneous discharge or chemical decomposition by the battery pack itself. If the battery pack fails to hold its operating duration after it has been fully charged, replace it with a new one. The battery pack may reach the end of its service life. Specifi cations Model: HA-G20BAT Rated Capacity: 14.8

• E-16 4 Screen Displays text and operating instructions. In addition, operations can be performed and data can be input using the stylus provided. 5 Microphone Used for audio input (including voice). 6 Power Key Turns the power on and off. 7 CLR Key Used to clear one letter to the left of the cursor. 8 Center Trigger Key Used to perform bar code reading. Can be ass

• Casio DT-X30 Series, E-25 Using the Laser Scanner (Laser Models) 1. After turning on the power, position the laser scanner close to a bar code and then press the trigger key. 2. The laser emits light and scans the bar code. If scanning is completed normally, Indicator 2 displays a green light. Important! If you are unable to scan a bar code, try changing the angle at which the scanner is held or distance from the scanner to the bar code, and then try scanning again. This Handheld Terminal is capable of scanning bar codes at a distance of about 40-410 mm (1 9 / 16 "-16 1 / 8 "). Furthermore, the di

• E-35 Handling SIM Cards The Handheld Terminal supports SIM card. Since the SIM card slot is located inside the battery pack compartment, fi rst remove the battery pack when installing or removing a SIM card. Refer to pages 18 to 20 for information on “Loading and Removing the battery pack”. Install (or replace) a SIM card according to the procedure described below. Installing 1. Check that

• Casio DT-X30 Series, E-33 Handling microSD Cards The Handheld Terminal supports microSD card. Since the microSD card slot is located inside the battery pack compartment, fi rst remove the battery pack when installing or removing a microSD card. Refer to pages 18 to 20 for information on “Loading and Removing the battery pack”. Install (or replace) a microSD card according to the procedure described below. Installing 1. Check that the power is turned off. If the power is on, always make sure to turn it off by pressing the Power Key. 2. Remove the battery pack. 3. Insert the microSD card with the top of the card (containing lettering) facing up by properly aligning with the slot. Althou

• Casio DT-X30 Series, E-45 Using the Ethernet Cradle (HA-G62IO) The optionally available Enthernet Cradle (HA-G62IO) makes it possible to transmit system data and fi le data between the Handheld Terminal and a PC via a USB or LAN connection (download or upload). You can also use the Ethernet Cradle to charge the battery pack installed in the Handheld Terminal. General Guide Top 8 9 Front 10 Back 7 6 54 3 2 1

• Casio DT-X30 Series, E-54 Connecting Multiple Dual Battery Chargers You can connect up to three Dual Battery Chargers. Doing so makes it possible to supply power to all the Dual Battery Chargers using one dedicated AC adaptor. 1. As shown in the illustrations below, remove the connector covers of the Dual Battery Chargers you want to connect to each other. 2. Connect the two Dual Battery Chargers as shown below. 3. Turn over the connected Dual Battery Chargers and attach a connection bracket, securing it in place with screws. You can repeat the a

• Casio DT-X30 Series, E-4 Warning Dust and Moisture Though the Handheld Terminal is dust and water splash resistant, its options including the battery pack are not. Keep loose metal objects and containers fi lled with liquid away from your Handheld Terminal and the options. Also, never handle the Handheld Terminal and the options while your hands are wet. Laser Light This product with the integrated laser scanning module scans bar codes using laser light. Never look directly into the laser light or shine the laser light into the eyes. x x Warning Interference with the Operation of Other Equipment (Using Wireless Data Communication) Keep your Handheld Terminal at least 22 centime

• Casio DT-X30 Series, E-22 Red Flashing: Battery pack problem Green: Charging complete Green Flashing: Standby due to the surrounding temperature being beyond the specifi ed temperature range (Approximately 0°- 40°C) (charging resumes when the temperature reaches the range.) Car Mounted-type Battery Charger Plug in the Car Power Cable accompanied in the box to the Car Mounted-type Battery Charger as illustrated below and the other end to the cigarette lighter socket in vehicle. The power LED on the front of the Car Mounted-type Battery Charger will light green if the Handheld Terminal has been properly mounted. Status of Indicator 1 on DT-X30: Orange: Charging Red

• Casio DT-X30 Series, E-5 Warning Avoiding Traffi c Accidents Never use your Car Mounted-type Battery Charger while operating a motor vehicle. Park your vehicle in a safe place before performing any operation. Never locate the Car Mounted-type Battery Charger where it might interfere with proper operation of the vehicle. Locate connecting cables as instructed by the manual, avoiding locations that can interfere with driving operations. Car Battery Power Should the Car Power Cable become damaged, replace it immediately with a new Car Power Cable when using the Car Mounted-type Battery Charger. x x x x Caution Installing in Vehicle To save

• Casio DT-X30 Series, E-23 Attaching the Hand Belt The hand belt can be used to prevent the Handheld Terminal from dropping when carrying it around. Attach the hand belt according to the procedure described below. To attach the hand belt 1. Thread the belt through the hand belt hole as shown in the fi gure. Then fold it back and secure using the hook-loop fastener. 2. Thread the other end of the belt through the hand belt hole and adjust the length so that it fi ts comfortably on your hand. Then secure using the hook-loop fastener. Important! Stic

• Casio DT-X30 Series, E-48 Using the Cradle-type Battery Charger (HA-G30CHG) The optionally available Cradle-type Battery Charger (HA-G30CHG) lets you charge the Handheld Terminal’s battery simply by placing the Handheld Terminal onto the charger. General Guide Top 3 2 Front 4 Back 1 1 AC Adaptor Jack Connect the AC adaptor (sold separately) here. 2 Terminal Detect Switch This switch detects when the DT-X30 is mounted correctly on the charger. 3 Power Contacts Power is supplied to the DT-X30 via these contacts. 4 Power LED This LED indicates the power status and the mountting status of the DT-X30. Off: DT-X30 is not installed Green: Powe

Related Products and Documents (Tablet):

Comparable Devices:

Similar Resources:

• Cisco TelePresence System Codec C20 (73 pages) 1Cisco TelePresence System Quick Set C20 / C20 Plus and Profiles using C20 Administrator guideD14637.04 Profile C20 and Quick Set C20 Administrator Guide TC4.0, November 2010. Copyright © 2010 Cisco Systems, Inc. All rights reserved.www.cisco.comAdministrator guideFor Cisco TelePresence System Quick Set C20 / C20 Plus and Profile 42” using C20Software ve …

• Prentke Romich Company Accent 800 (28 pages) 18664v1.01 Getting Started For Accent® 800 Devices with NuVoice® Software Applies to Accent 800 Models with Serial Numbers 10000AC8 and Higher …

• Control Vision Anywhere DeX (51 pages) Anywhere Map DeX OWNERS MANUAL Elements of this product are protected under US patent numbers 6,804,585 and 7,167,782. Other patents may be pending Control Vision Corp Pittsburg Kansas www.anywheremap.com …

• a-riaval PAD (29 pages) 1 Usermanual Hotline +49 (0) 511 - 270 496 90 www.a-rival.de * [email protected] Dear Customer : Firstly, we really appreciate we can provide our best service to you! Please kindly read this instruction before you start using the product. This Instruction manual can explain product basic feature, can help you to well operate the …

• TCL Alcatel POP4-10 4G&VF (44 pages) L2 Repair Document TCL Communication Ltd. Rev. 9030G/9030Q/VDF1400 Level 2 Repair Document Page 1.0 1/44 All rights reserved. Transfer, copy, use or communication of this file is prohibited without authorization. POP4-10 4G&VF 9030G/9030Q/VFD1400 Note: this manual is non-contractual and TCL Com …

• Saltillo TouchChat Express (188 pages) Saltillo Corporation 2143 Township Road 112 Millersburg, OH 44654 www.saltillo.com 10144 Version 1.5 / Versión 1.5 English/Spanish User's Guide Guía de uso Inglés/Español TouchChat™ Express TouchChat™ Express-mini …

Comments, Questions and Opinions: