Contec IPC-DT 61 Operation & User’s Manual
|
Contec IPC-DT 61, 7. Screen Adjustment and a Setup DISPLAY ADJUST : Adjusts the display position. Selecting this item displays a sub-menu. Use [+] and [-] to move between items and [MENU] to select. SCREEN MANAGER 640x480 60.0Hz V.POSITION V.POSITION SP WIDTH PHASE AUTO SETUP HORIZONTAL POSITION H.POSITION A A Figure 7.2. DISPLAY ADJUST Sub-Menu Screen H.POSITION: Select this item to adjust the horizontal position of the screen. Press [+] or [-] while checking the screen to optimize the item. V.POSITION: Select this item to adjust the vertical position of the screen. Press [+]
Contec IPC-DT 61, 9. Touch Panel USB Multi-Touch Panel This function can be used in the case when the RGB signal from the host computer is split for connecting to multiple displays via a splitter. The function permits touch panel operation to be used at all the displays. A maximum of eight touch panel displays can be connected. Note that all touch panels must be connected via USB and, to allow the touch panel driver software on the host computer to identify each device, a different USB ID must be set on the DIP switch located on the side of each display unit. USB ID7 USB ID0 POWER
Contec IPC-DT 61, 11. Options 11. Options Screen protective sheets - IPC-CV6 : 6.4-inch screen protective sheets (10 sheets) - IPC-CV : 10-inch screen protective sheets (10 sheets) - IPC-CV12 : 12.1-inch screen protective sheets (10 sheets) - IPC-CV15 : 15-inch screen protective sheets (10 sheets) Cable - IPC-DVI/D-020 : DVI-D cable (2m) - IPC-DVI/D-050 : DVI-D cable (5m) - IPC-PLDVI-020 : Panel link - DVI-D conversion cable (2m) - IPC-PLDVI-050 : Panel link - DVI-D conversion cable (5m) - IPC-CBL3-2 : Touch panel, COM cable (2m) - IPC-CBL3-5 : Touch panel, COM cable (5m) Driver - IPC-SLIB-01 : Driver & Utility Soft Set (CD-ROM version) Others - IPC-ACCODE3
Contec IPC-DT 61, 3. Outside Dimensions and Part Names Analog RGB Connector Table 3.1. Analog RGB Connector Connector type Pin NO. 1 2 3 4 5 6 7 8 Pin NO. 9 10 11 12 13 14 15 Signal name RED GREEN BLUE N.C. GND R-GND G-GND B-GND Signal name N.C. GND N.C. DDC DATA HSYNC VSYNC DDC CLK 15-pin HD-SUB (FEMALE) 5 1 11 15 10 6 RS Touch Panel Connector This connector is RS-232C compliant to be used for touch panel data communication with the host computer. Table 3.2. RS Touch Panel Connector Connector type Pin NO. 1 2 3 4 5 Pin NO. 6 7 8 9 Signal name 10K pull down TxD RxD N.C. GND Signal name 10K pull down N.C. 10K pull down 10K pull down 9-pin D-SUB (MAL
7. Screen Adjustment and a Setup 7. Screen Adjustment and a Setup The equipment has screen adjustment switches [MENU], [+], and [-]. Use these switches to adjust the screen. (For the locations of the switches, see “Part Names” in Chapter 3.) When using the equipment for the first time or after changing the output screen mode of the host computer
Contec IPC-DT 61, 1. Introduction Connecting to a host with an existing touch panel function such as a CONTEC panel computer. This touch panel cannot be used with a touch panel mounted in the host computer. In this case, the touch panel function will be unavailable but screen display will still work normally. However, on the following CONTEC panel computers, multiple touch panels can be used together when connected via the USB interface. - IPC-PT/630 Series: IPC-PT/H630X(PCI)C, IPC-PT/H630X(PCI)CP , IPC-PT/L630S(PCI)C, IPC-PT/L6
2. Specifications General Specifications Table 2.4. General Specifications Item Specification Environment Operating temperature 0 - 50ºC (0 - 40ºC when using an IPC-ACAP12-01 (AC switching adapter)) Storage temperature -10 - 60ºC Operating humidity (20 - 80% when using an IPC-ACAP12-01 (AC switching adapter)) (No condensation allowed) Floating dust Nor
Contec IPC-DT 61, 5. Connection to the Host Computer When connecting to a IPC-BX/M600(PCW) Series If using this box computer, set the "Embedded" - "CRT/FPD" BIOS setting to "AUTO Select" or "SW Select". If you select "SW Select", set the switch (S1) on the box computer board as shown below. Table 5.7. S1 Switch Settings IPC-DT/S61VT-DC1 IPC-DT/M61VT-DC1 IPC-DT/M61VT-AC0 IPC-DT/L61SVT-DC1 IPC-DT/L61SVT-AC0 IPC-DT/H61XT-DC1 IPC-DT/H61XT-AC0 12345678 ON 12345678 ON 12345678 ON 12345678 ON When connecting to a IPC-BX/M630(PCI) Series No specific host settings are required if using this box computer. However, if using the Windo
Contec IPC-DT 61, 6. Power Supply Connection AC adapter code removal prevention fitting (1) Insert the plug of AC Adapter. (2) Tighten the screws on the attachment fitting. Figure 6.2. Code Removal Prevention Fitting 34 User’s Manual
Contec IPC-DT 61, 3. Outside Dimensions and Part Names Part Names XXXXXXXXX XXXXXXXXXXXXXXXXXX SERIAL No. : XXXXXXXXXXXXX MODEL : XXXXXXXXX XXXXXXXXX CAUTION! The screw bolting torque of attachment must be 0.6N-m(MAX). XXXXXXXXXXXXXXXXXXINPUT : Front Back Right side Left side Screen & Touch panel Screen adjustment switch AC adapter jack Analog RGB connector RS touch panel connector USB touch panel connector DVI-D connector +12VDC power connector P ES CN TI PAS S POWER LED USBVGADVICOM 1 2 12VDC-IN CAUTION! 12VDC-I N*1* 2** * 12VDC-IN si mult an eously . Don't co nn
Contec IPC-DT 61, 9. Touch Panel 9. Touch Panel This equipment has a touch panel that enables keyboard-less, mouse-less operations by communication with the host computer using the RS-232C cable. Touch panel POWER +- ME NU ESC Host PC Touch panel controller Touch panel CPU Communication controller INT CPU Serial communication Figure 9.1. Touch Panel and Block Diagram Data input at the touch panel is processed by the touch panel controller and passed to the host PC via the serial port on the CPU in the controller. Before the touch panel
Contec IPC-DT 61, 4. Hardware Setup Attaching the Fitting Used to Attach to the Main Unit (1) Hold the main unit from the outside of the panel. Figure 4.6. Attaching the Fitting Used to Attach to the Main Unit < 1 / 2 > (2) Hold the attach from the inside of the panel. Panel Main body Overtightening screws may result in damage. Example of figure:IPC-DT/M61VT-xxx Metal fittings Figure 4.6. Attaching the Fitting Used to Attach to the Main Uni < 2 / 2 > User’s Manual 23
7. Screen Adjustment and a Setup COLOR CONTROL: Adjusts the color temperature. Selecting this item displays a sub-menu. Use [+] and [-] to move between items and [MENU] to select. You can select USER COLOR MODE to adjust RED, GREEN, and BLUE manually. SCREEN MANAGER 640x480 60.0Hz 6500 5000 USER COLOR MODE COLOR TEMPERATURE R G B R G B R G B 9300 R G B K K K Figur
Contec IPC-DT 61, 5. Connection to the Host Computer C onnection to the Host Computer 5. Purchase individual connection cables as they are not bundled with this equipment. Analog RGB Connection Connect the analog RGB input on this unit to the analog RGB connectors on the host computer. Table 5.1. Recommendation Display Cable Model Maker Cable length KC-V2 SANWA SUPPLY INC. 2m KC-V5 SANWA SUPPLY INC. 5m If you use any other cable, select a shielded cable the wire carrying the RGB and H/Vsync signals and the grounded wire in a twisted pair. Note that a non-twisted-pair cable may degrade image quality, in particular, which is longer than 2 m. Any loss of image quality due to use of
Contec IPC-DT 61, 5. Connection to the Host Computer Touch Panel Data Communications These connections are used to send touch panel data to the host computer via the USB or RS-232C serial port. Connect to the USB port or serial port (COM port) on the host computer. Table 5.8. Example of a USB connection cable (USB Type A(Host) Û Type B(Display)cable) Model Maker Cable length KU20-2H SANWA SUPPLY INC. 2m KU20-5H SANWA SUPPLY INC. 5m Table 5.9. Option Cable (RS-232C Straight Cable) Model Maker Cable length IPC-CBL3-2
Contec IPC-DT 61, 3. Outside Dimensions and Part Names IPC-DT/M61VT-AC0 8-M4 TAP 39.3 67.4 [mm] 226 291 49 5 18.5 38.5 75 100 100 75 6.5 27.5 8 67.5 148 305 216.2 163.4 87.7 240 (Maximum tapping length : 5mm) VGADVI USBCOMLN POWER MENU -+ ESC Figure 3.5. Outside Dimensions of Main Unit (IPC-DT/M61VT-AC0) IPC-DT/L61SVT-AC0 8-M4 TAP 302 54.5 5 21.5 41.5 242 40.367.4 67.5 148 256 96.8 189.5 251 316 [mm] 6.5 27.5 100 75 100 75 8 (Maximum tapping length : 5mm) VGADVI USBCOM NL POWER MENU - + ESC Figure 3.6. Outside Dimensions of Main Unit (IPC-DT/
Contec IPC-DT 61, 7. Screen Adjustment and a Setup TOUCHPANEL: Select this item to adjust the status of the touch panel. Select this item to invoke the submenu, select a desired item using [+] or [-], then press [MENU] to accept the setting made. SCREEN MANAGER 640x480 60.0Hz DISPLAY ID INTERVAL MODE BEEP TOUCH PANEL ON/OFF ON/OFF I D Mode Figure 7.5. TOUCH PANEL sub menu ON/OFF: Select this item to turn ON (enable) or OFF (disable) the touch panel operation. (The equipment is started always with this item s
Contec IPC-DT 61, 3. Outside Dimensions and Part Names DVI-D Connector Table 3.4. DVI-D Connect r o DVI-I 24pin Connector 1 8 17 24 16 9 Pin No. Signal name Pin No. Signal name 1 TMDS DATA2- 13 N.C. 2 TMDS DATA2+ 14 +5V 3 TMDS DATA2 SHIELD 15 GND 4 N.C. 16 HPD 5 N.C. 17 TMDS DATA0- 6 DDC CLK 18 TMDS DATA0+ 7 DDC DATA 19 TMDS DATA0 SHIELD 8 N.C. 20 TXD 9 TMDS DATA1- 21 RXD 10 TMDS DATA1+ 22 TMDS DATA0 SHIELD 11 TMDS DATA1 SHIELD 23 TMDS CLK+ 12 N.C. 24 TMDS CLK- 20 User’s Manual
Contec IPC-DT 61, 3. Outside Dimensions and Part Names Screen adjustment switch Front Screen & Touch panel POWER LED AC power supply terminals Back Right side Left side Analog RGB connector RS touch panel connector USB touch panel connector COM USBDV VGA NL DVI-D connector POWER MENU -+ ESC Figure 3.10. Part Names(IPC-DT/M61VT-AC0, IPC-DT/L61SVT-AC0, IPC-DT/H61XT-AC0) User’s Manual 17
Contec IPC-DT 61, 1. Introduction - When the surface or frame of the touch panel has become dirty, wipe it with neutral detergent. Do not wipe the touch panel with thinner, alcohol, ammonia, or a strong chlorinated solvent. - Do not plug or unplug the connector with the equipment powered on. as doing so may result in a malfunction or fault. - This product is not intended for use in aerospace, space, nuclear power, medical equipment, or other applications that require a very high level of reliability. Do not use the product in such applications. - If you utilize this product in such usages where high reliability and safety are required
7. Screen Adjustment and a Setup Direct Key CONTRAST : Pressing the [+] key when the menu is not displayed opens the contrast adjustment screen. BRIGHTNESS : The brightness of the backlight can be adjusted by pressing the [+] and [-] keys without the menu screen displayed. RESET : All the settings can be reset to the factory defaults by turning on the equ
Contec IPC-DT 61, 1. Introduction Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or in property damage. Handling Prec
ViewSonic VA2046a-LED Monitor Brochure & specs
VA2046a-LED |
Contec IPC-DT Monitor Operation & user’s manual
IPC-DT |
Pico Macom MOR-LCD4 Monitor Specifications
MOR-LCD4 |
Smappee Energy monitor Monitor Installation manual
Energy monitor |
Epson 7900p - PowerLite XGA LCD Projector Monitor Operation & user’s manual
7900p - PowerLite XGA LCD Projector |
Lorex L24LE11B Monitor Operation & user’s manual
L24LE11B |
HP Compaq Elite 8300 All-in-One Monitor Specification
Compaq Elite 8300 All-in-One |
YORKVILLE LS800P Monitor Owner's manual
LS800P |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Nokia | 3610 | Operation & user’s manual | nokia/3610-Q44.pdf | 04 Apr 2024 | 121 | |
2 | Wexiodisk | WD-6C | Installation and operation manual | wexiodisk/wd-6c-I4A.pdf | 22 Jul 2023 | 33 | |
3 | CYBEX | 750C | Owner's manual | cybex/750c-37E.pdf | 11 Apr 2023 | 84 | |
4 | Coleman | 5155B | User manual manual | coleman/5155b-K93.pdf | 16 Dec 2023 | 32 | 0.99 Mb |
5 | Epson | Stylus C80N | Setup and installation manual | epson/stylus-c80n-98F.pdf | 10 Feb 2023 | 58 | 1.29 Mb |
6 | Sea Tel | 2406-7 | Installation and operation manual | sea-tel/2406-7-814.pdf | 02 Mar 2024 | 76 |
Sony
5-019-497-11(1)Professional Video MonitorOperating InstructionsBefore operating the unit, please read this manual thoroughly and retain it for future reference.PVM-X2400/X1800Software Version 1.0© 2020 Sony Corporation
…
TRIMASTER PVM-X2400(55 pages) |
HP
Product End-of-Life Disassembly Instructions Product Category: Monitors and Displays Marketing Name / Model [List multiple models if applicable.] HP HC270cr Display Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions for the disassembly of HP products to remove components and mat …
HC270cr(18 pages) |
Pioneer
ORDER NO.PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, JapanPIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, BelgiumPIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936PIONEER CORPORATION 2003ARP3156T – ZZR …
PDP-433CMX(159 pages) |
Samsung
Contact SAMSUNG WORLDWIDEIf you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. CountryCustomer Care Centre Web SiteAUSTRIA 0800-SAMSUNG (726-7864) www.samsung.com/atBELGIUM 02 201 2418 www.samsung.com/beCZECH REPUBLIC800-726-786 (800 - SAMSUNG) www.samsung.com/czDistributor pro Českou republik …
7+ series(153 pages) |
Runco
PLASMAWALL™ PL-50HDXPLASMAWALPLASMAWALL™™ PL-50HDX PL-50HDXPFP™P L A S M A W A L L™ F L A T P A N E L D I S P L A Y M O N I T O R S A N D P F P ™ C O N T R O L L E R SCUTTING EDGE DISPLAY MONITORREVOLUTIONARY DIGITAL PROCESSINGFOR FIXED PIXEL DEVICESP I X E L F O R P I X E L™R U N C O I N T E R N A T I O N A L© 2003 Runco In …
PL-50HDX(2 pages) |
NEC
LCD1800 OUTLINESCALE : NTSDIMENSION IN mm.Fig.-1-11.548138.5289.4361.2460397CONTROL SWITCHPOWER-ON INDICATIONPOWER SWITCH220NOTE : • CABINET COLOR : MIST WHITE #8510 • TILT ANGLE : +35˚ ~ -5˚ • SWIVEL : ±45˚ • WEIGHT WITH STAND : APPROX 8.2 kg WITHOUT STAND : APPROX 6.4 kgCOVERCABLE COVERDC POWER INLET …
LCD1800(2 pages) |
Proctor-Silex Coffee Maker 840251801Coffee Maker #UL2C18 840251801, 36 |
DECstation Desktop 200DECstation 200 Manual (Doc Type: Desktop Hardware installation manual) 200, 32 |
Shandong New Beiyang Information Technology Co. Label Maker BTP-3200EShandong New Beiyang Information Technology Co. BTP-3200E User Guide (Operation & user’s manual), @P4M1R4 BTP-3200E, 53 |
Hyundai Automobile VeracruzHyundai Veracruz Manual (Doc Type: Automobile Quick reference manual) Veracruz, 22 |
Briggs & Stratton Portable Generator 030210PDF User Manual (@4HSPIM), Briggs & Stratton 030210 Portable Generator (18/12/2023) 030210, 6 |
GE Cooktop PP945SMSSGE PP945SMSS Cooktop Installation instructions manual PP945SMSS, 16 |
Bodum Coffee Maker CHAMBORD 10616Bodum CHAMBORD 10616 Guide (User manual manual), @95ZB6M CHAMBORD 10616, 11 |
Razor Scooter E100 series#34CKS7: E100 series Scooter Manual E100 series, 16 |
Crown Processor PIP-FMXPIP-FMX (Processor ePDF User Guide, #4Z9U98) PIP-FMX, 4 |
Bowers & Wilkins Speakers DM220Bowers & Wilkins Speakers Specifications (File: bowers-wilkins-dm220-speakers-1, Wed 09.2023) DM220, 1 |
Olimpia splendid Air Conditioner DIFFUSIONE 10.5 HP HEOlimpia splendid DIFFUSIONE 10.5 HP HE Air Conditioner Instructions for installation, use and maintenance manual DIFFUSIONE 10.5 HP HE, 108 |
Flash DJ Equipment F7100496#UIAJ18 F7100496: Flash DJ Equipment Owner Documentation F7100496, 10 |