Manualios.com

Casio DT-800RF Supported Equipment Manual

Casio DT-800RF Manual Online:

3.7, 2999 votes
Casio DT-800RF User Manual
Casio DT-800RF User Guide
Casio DT-800RF Online Manual

Text of Casio DT-800RF User Guide:

  • Casio DT-800RF, Table of Contents Chapter 1 • Introduction............................................................................................. 1-1 Description………………… ..........................................................................................1-1 Picture………………………...........................................................................................1-2 Setup Requirements…….. ...........................................................................................1-2 Accessories………………............

  • Error Message Resolution Guide Message Reason Solution Reference Tech Note Auto/Pulse; Prompt. Advisory message. --- Auto/No Pulse; Prompt. Advisory message. --- Wand Simulation; Prompt. Advisory message. --- VT100; Prompt. Advisory message. --- VT220; Prompt. Advisory message. --- SETUP; Prompt. Adviso

  • Casio DT-800RF, Copyright © 1996 - 2006 by Connect, Inc. All rights reserved. This document may not be reproduced in full or in part, in any form, without prior written permission of Connect Inc., 1701 Quincy Avenue, Suites 5 & 6, Naperville, IL 60540. Connect, Inc. makes no representation or warranties with respect to the contents of this document and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Connect, Inc. reserves the right to revise this publication and to make changes to it from time to time without obligation

  • Terminal Setup To set these addresses from the Settings menu, click on Servers and then click on Add. Enter the name of each server, its IP Address and IP port (normally 23 for Telnet servers), and emulation type. Then click on OK. Repeat this step for each telnet server the terminals are required to access. If an error is made in the name, IP Address, IP Port number, or Te

  • Casio DT-800RF, Introduction Operating System Version of the Operating System The version of the operating system on a DT-800RF terminal is 2.00. Finding the Version of the Operating System The version of operating system will appear on a terminal screen when the terminal is rebooted. For rebooting instructions, see Command Mode Boot in the Quick Start section. Supported Equipment Manual • March, 2006 1-4

  • Casio DT-800RF, Quick Start 3. Press the Clear key. 4. Select 1: yes. 5. Press the Clear key to return to the system menu. 6. Select 4: Transmit, 4: Utility and 4: Change memory size. 7. Enter 640 and then press the Enter key. 8. Select yes to change the size. 9. Press the Clear key to return to the system menu. 10. Select 1: Execute AP. 11. Select Enter for “yes” to execute the AP. The terminal is now configured to accept a download from Twin Client Manager. Starting a Telnet Sess

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note Backlight Time; Prompt. Advisory message. --- Enter Key Action; Prompt. Advisory message. --- Reset Options; Prompt. Advisory message. --- Font Size; Prompt. Advisory message. --- Portable Printer; Prompt. Advisory message. --- Reprint Option; Prompt. Advisory message. --- Data IDs; Prompt. Advisory message. --- Internal/External; Prompt. Advisory message. --- Modify Beeps; Prompt. Advisory message. --- Mes

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note Font Loading Error; Could not load the font. Ensure that the font is available to load. --- Printer Not Ready\nPress R to Retry\nC to Cancel Print; Can not print. Check cable, battery, communication settings and paper in the printer. --- Mobile Unit in\nDemonstration Mode\nfor TwinClient; Running in demo mode. Purchase a license from Connect. --- Connected to Host; Successful connection to the target Host. Advisory message. --- Telnet Mode not\nsupported on\nthis Mobile Unit; This Mobile Unit must be used wi

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note Control Codes; Prompt. Advisory message. --- Local Echo; Prompt. Advisory message. --- <BK SP> Sends; Prompt. Advisory message. --- New Line Mode; Prompt. Advisory message. --- Insert Mode; Prompt. Advisory message. --- Autowrap Mode; Prompt. Advisory message. --- Cursor; Prompt. Advisory message. --- EMULATION SETUP; Prompt. Advisory message. --- Mobile Unit Type; Prompt. Advisory message. --- Local Echo; Prompt. Advisory message. --- Supported Equipment Manual • March, 2006 4-15

  • Casio DT-800RF, Terminal Setup Any group can be made the default group by clicking on the group, and then clicking on the right mouse button. Then click on the Make Default option. Reassigning Terminals After a terminal has been configured and assigned to the default group, it can be reassigned to a new group by clicking on the terminal icon as shown below. Then, holding the mouse button down, drag the terminal icon to the desired group as shown next. Release the mouse button, which reassigns the terminal. The next time the terminal is rebooted, it will be reconfigured as defined in the group

  • Casio DT-800RF, Terminal Setup Installation The InstallShield wizard runs and presents the following screen. Click on Next to begin the installation process. Supported Equipment Manual • March, 2006 2-2

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note Domain Name Server\nNot Set; DOMAIN NAME SERVER not configured. Configure the Mobile Unit with the correct network IP information. --- Domain Name Server\nQuery Memory Error; Memory error on the Mobile Unit Expand the Mobile Unit memory or return the Mobile Unit for repair. --- Domain Name Server\nQuery Sending Error; Mobile Unit out of the coverage area. Most likely a range, access point, radio, host or network issue. Troubleshoot the customer’s environment. T1113, T1114, T1161, T1171, T1187 and T1194 Domain Name Server\nQuery

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note Connection ERROR.\nREBOOT MOBILE UNIT; Could not Connect. Verify that your Network settings are correct and you are in the correct mode using the correct Port. T1113, T1114, T1161, T1171, T1187 and T1194 Disconnect ERROR.\nREBOOT MOBILE UNIT; Could not Disconnect. Verify that your Network settings are correct and you are in the correct mode using the correct Port. T1113, T1114, T1161, T1171, T1187 and T1194 RF Send ERROR.\nREBOOT MOBILE UNIT; Could not Send.

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note Mobile Unit Out\nOf Range, Unable\nTo Receive; Mobile Unit out of the coverage area. Most likely a range, access point, radio, host or network issue. Troubleshoot the customer’s environment. --- Printer Not\nResponding; Can not print. Check cable, battery, communication settings and paper in the printer. --- Printer Out\nOf Range; Printer out of the coverage area. Most likely a range, access point or radio issue. Troubleshoot the custome

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note INVALID KEY; The key pressed is not valid. Ensure that you are entering input into the correct field. --- MUST CLEAR FIELD; Trying to enter data in a field that must be cleared first. Ensure that you are entering input into the correct field. --- SCAN NOT ALLOWED; Trying to scan into a key only field. Ensure that you are entering input into the correct field. --- KEY NOT ALLOWED; Trying to key into a scan only field. Ensure that you are entering input into the correct field. --- ENTRY TOO SHORT; Trying to exit the f

  • Casio DT-800RF, Keypad Table F3 <FUNC><3> <FUNC><3> <FUNC><3> F4 <FUNC><4> <FUNC><4> <FUNC><4> F5 <FUNC><5> <FUNC><5> <FUNC><5> F6 <FUNC><6> <FUNC><6> <FUNC><6> F7 <FUNC><7> <FUNC><7> <FUNC><7> F8 <FUNC><8> <FUNC><8> <FUNC><8> F9 <FUNC><9> <FUNC><9> <FUNC><9> F10 <FUNC><0> <FUNC><0> <FUNC><0> F11 <LEFT><FUNC><1> <LEFT><FUNC><1> <L

  • Casio DT-800RF, Terminal Setup Creating New Groups New groups, with different configurations, can be created by clicking on Terminal Group Manager , and then clicking the right mouse button as shown. After the new group has been created, the group settings option becomes available for change, as shown below. After the Configuration File and all of the other parameters have been set, the group is made active by clicking on the Active check box. Supported Equipment Manual • March, 2006 2-24

  • Casio DT-800RF, Chapter 2 • Terminal Setup Running Setup from a Download File The downloaded file is a compressed archive. After extraction using a utility such as WinZip or PKWARE, folders are created on the hard disk as shown in the following figure. Click on the Disk1 folder to view the files as shown in the following figure. Click on the Setup application and proceed to the following section entitled Installation for further instructions. Supported Equipment Manual • March, 2006 2-1

  • Casio DT-800RF, Error Message Resolution Guide Message Reason Solution Reference Tech Note External; Prompt. Advisory message. --- none; Prompt. Advisory message. --- monarch; Prompt. Advisory message. --- pddumb; Prompt. Advisory message. --- comtec; Prompt. Advisory message. --- rascal; Prompt. Advisory message. --- codewriter; Prompt. Advisory message. --- comtec(S); Prompt. Advisory message. --- User Name; Prompt. Advisory message. --- Password; Prompt. Advisory message. --- Supported Equipment Manual • March, 2006 4-22

  • Casio DT-800RF, Chapter 1 • Introduction Description The DT-800RF has a versatile high-speed scanning (100 scans per second) that ensures a rapid first-time read rate and high data integrity. Its combination of distance and contact laser scanning allows bar codes to be easily read even when badly printed on curved and irregular surfaces. Amongst the lightest weight terminals in its class, the compact lightweight design of the DT-800RF reduces operator fatigue over extended usage periods. Its backlit display can be illuminated, enabling readings to be clearly seen in the darkest of work environments. This terminal has a world-class water splash proof (IPX II standard) that pro

  • Casio DT-800RF, Terminal Setup Standard Setup The default terminal setup is sufficient for most installations. However, to meet site- specific requirements, it may be necessary to customize terminal operation. The standard setup options simplify this process and can be modified using one of the following methods: • Using the Twin Client Manager. • Using the Twin Client terminal menu system. Standard Setup describes how to use the Twin Client Manager and the terminal menu systems to set up the terminal. Also described are the metho

  • Error Message Resolution Guide Message Reason Solution Reference Tech Note Error receiving host\nlist from Server; Bad Protocol detected. Usually a result of bad cabling, power or faulty transceiver. Also, will receive this if the Mobile Unit is in the wrong mode for server operation. --- Unexpected Server\ndata received; Bad Protocol dete

  • Chapter 3 • Keypad Configuration Keypad Figures Casio DT-800RF 5250 Left Func Right PWR BS LOCK del reset FNC F 9 F17 F7 F 8 newline numbovr redraw F17 F7 F1 8 F 8 F1 9 F 9

Related Products and Documents (Tablet):

Comparable Devices:

# Manufacturer Model Document Type File Updated Pages Size
1 Sparky Group BAR 12E Instruction manual sparky-group/bar-12e-855.pdf 07 Mar 2024 54 1.59 Mb
2 CMA Dishmachines MODEL GL-C Installation and operation manual cma-dishmachines/model-gl-c-IB7.pdf 10 Oct 2023 11 0.33 Mb
3 Setec DRIFTER Owner's manual setec/drifter-6N3.pdf 24 May 2023 6
4 Tassimo TAS-1000UC Operation & user’s manual tassimo/tas-1000uc-XU9.pdf 15 Jul 2023 24 3.2 Mb
5 RTS Fiber Optic Interface Back Card Installation instructions rts/fiber-optic-interface-back-card-L73.pdf 14 Jul 2022 2 0.37 Mb
6 Airlink101 APL8511 Quick installation manual airlink101/apl8511-T7P.pdf 08 Feb 2024 1 0.09 Mb

Similar Resources:

  • Haier

    PAD700

    (14 pages)
    FCC StatementThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if notinstalled and us …
  • Asus

    EEE PAD ME171

    (26 pages)
    Eee Pad User ManualME171E6617ASUS is devoted to creating environment-friendly products/packagings to safeguard consumers’ health while minimizing the impact on the environment. The reduction of the number of the manual pages complies with the reduction of carbon emission.For the detailed user manual and related information, refer to the user manual include …
  • Casio

    V-T500-E

    (59 pages)
    CASIO V-T500/V-N500 Series Hardware Manual (Version 1.08) CASIO Computer Co., Ltd. Copyright © 2013. All rights reserved. October 2013 …
  • Venturer

    CT9378W2

    (10 pages)
    CT9378W2User ManualIt's important to read this instruction prior to using your new product for the first time.7” TabletScan for more user manual details …
  • Winmate

    W10IB3S-PCH2AC-PoE S-Series

    (17 pages)
    10.1"S-Series HMI W10IB3S-PCH2AC-PoE (with LED light bar) W10IB3S-PCH2-PoE (without LED light bar) Slim-line Quick Start Guide Version 1.0 Document Part Number: 9154111I100A …
  • Amazon

    Kindle Fire

    (6 pages)
    Charge your Kindle by plugging it into a U.S.-compatible electrical outlet. You can also detach the USB cord from the power adapter* and connect it to a computer to charge your Kindle or to transfer data.The charge indicator light will turn yellow indicating that the battery is charging; you can continue to use your Kindle while it charges. A gre …

Comments, Questions and Opinions: