Century Swift Carbon 550 Instruction Manual
|
Century Swift Carbon 550, Linkage for Rudder servo: Preset length by factory. View: Right Side CCPM Servo Guidelines 8. Installing and Adjusting Control Components The goal in the end after all the servos are mounted is to have the swashplate sit level or at 90 degrees to the main shaft and have the swashplate move equally fore, aft and side to side. The swashplate will also travel up and down as the three servos work together. This will result if the previous instructions have been followed and the ATV function for the three CCPM servos has been set very, very accurately to eliminate pitch change when moving the aileron or elevator sticks. Setting Up the Rudder
Century Swift Carbon 550, There are three servos that are mounted on the left and right main frames. They work together to tilt the swashplate producing the collective pitch, roll cyclic pitch (aileron control) and the fore-aft cyclic pitch (elevator control). Before be- ginning this section you should center all servos using the radio. All servo arms must be set with linkages as pictured at 90 degree angles. All servos mount with M2.5x12 self tapping screws, M2 servo balls and M2 Nuts. IMPORTANT: Century logo on all ball links must face OUTWARD as pictured. The pitch servo will mount with a full servo arm on the lower opening of the left side of the main frame. The dis- tance between the steel bal
Century Swift Carbon 550, The canopy may require cutting to make space for certain batteries or other extras. We recommend the use of a dremel. A face mask and goggles should be used when cutting berglass Cut the windshield of the canopy to align with the windshield lip of the canopy. Use the supplied hardware to attach the windshield to the canopy. (HINT:) Use Krylon ‘Fusion’ paint if attempting to paint. Make sure the canopy’s surface is free from oils prior to applying the decals. Decals are designed for application as pictured. Mount the decals in such a way that they do not come too close to the canopy mounting grommets. Mount the c
Century Swift Carbon 550, 12. Pre-Flight Basic Hovering When all is set, ready and checked, attach your training gear/pod and plug in your battery. Place the helicopter pointing into the wind and stand behind the model about 15’ away. Always watch the nose of the helicopter, move the rudder left and the nose will move left. Start by increasing the throttle slowly until the helicopter rises 2-6 inches off the ground then set it back down. Repeat this process until you become comfortable with the holding the model in the same spot for a few seconds then
Century Swift Carbon 550, 5. Safety Before ying, please check to make sure no one else is operating on the same frequency. Before ight, please check if the batteries or transmitter have enough capacity. Before turning on the transmitter, please check to ensure the throttle stick is in the lowest position. IDLE switch is Off. When turning on the unit, please follow the power on/off procedure. Power ON - Turn on the transmitter rst and then turn on the receiver. Power OFF - Turn off the receiver rst and then turn on the transmitter. If this protocol is not followed, c
Century Swift Carbon 550, 2. Battery Warnings & Safety For Lithium Polymer and NiMH/NiCD cell or battery packs purchased. 1. Never fast-charge any battery type unattended. 2. Never charge Li-Poly cells or battery packs at any rate unattended. 3. Only charge Li-Poly cells or battery packs with a charger designed specically for lithium polymer chemistry. 4. Li-Poly cells can ignite because of unmatched cell capacity or voltage, cell damage, charger failure, incorrect charger setting and other factors. 5. Always use the correct charging voltage. Li-Poly cells or battery packs
Century Swift Carbon 550, Cap Screw M3x18 (CNM3x18CS) Set Screw M3x4 (CNM3x4SS) Landing Skids (CNE513) Cap Screw M3x8 (CNM3x8CS) Hint: Place strut into a cup of warm water, if skid does not slide through the hole of the strut. *Apply light CA to M3x4 set screw. CF Battery Support Plate (CNE514) M3 Locknut Landing Gear Assembly 6. Assembly Instructions CA CA 16 M3 Locknut Button Head Cap Screw M3x8 (CNM3x8BH) THREAD LOCK B CF Switch Plate (CNE572) THREAD LOCK B Landing Struts (CNE512) Main Frame Braces (CNE584) CNC Switch Plate Standoffs
Tail Rotor Blades (CNE541) Tail Blade Grip (CNE540) Rotor Hub (CNE539) Set Screw M3x4 (CNM3x4SS) Bearing M3x8x3 (CNBB038) Linkage Ball (CNLR1014) M3 Locknut Button Head Screw M3x14 (CNM3x14BHCS) Bearing 3x8x3 (CNBB038) Cap Screw M3x16 (CNM3x16CS) Tail Blade Grip (CN540) CF Vertical Fin (CNE536) Tail Gear Box (CNE528) Tail R
Century Swift Carbon 550, Final Adjustments - Tail Rotor Setup 11. Final Preparations Gyro Gain Adjustment The gyro assists in holding the tail rotor, actually compensating for changes in wind direction or quick movements. First check that the gyro is installed correctly by watching the rudder servo. While holding the rotor head move the rudder stick to the right and observe the direction the servo arm moves. Now quickly rotate the nose to the left, the servo horn should move in the same direction. If the rudder servo horn moves in the opposite direction reverse the gyro direction. Generally the starting setting for the gyro gai
Century Swift Carbon 550, 1. Introduction Congratulations on your purchase of Century Helicopter Product’s Swift Carbon 550 Kit. The Swift Car- bon 550 is a high performance machine providing the agility and durability that is expected out of a heli- copter of this caliber. The attention and praise by the R/C helicopter community is well deserved as the Century Swift line is unmatched in affordability, quality and performance. In order to take advantage of your Swift’s performance capabilities we recommend using a high quality computer radio system with 120 degree eCCPM mixing. The radio syste
Century Swift Carbon 550, Main Frame Assembly 6. Assembly Instructions Washer M10x14x.5 (CNE592) Main Gear (CNE510A) Auto-rotation Hub and Bearing (CNE510B) Flush Head Cap Screw (CNM3x8FHCS) Main Gear (CNE510A) Flush Head Cap Screw (CNM3x8FHCS) Driven Tail Hub (CNE591) Split Gear Assembly Button Head Cap Screw M3x8 (CNM3x8BH) Button Head Cap Screw M3x8 (CNM3x8BH) 1. Place the two side frames together with the elevator A-arm assembly in- between them. When looking through the back the elevator bellcrank should be on the left side. 2. Fi
Century Swift Carbon 550, Washout Base (CNE516) Linkage Ball (CNLR1014) Washout Control Arm (CNE516) Bearing 3x6x2.25 (CNBB36) Cap Screw M3x8 (CNM3x8CS) Flat Washer M3x5x.5 (CNLR1003) Medium Linkage Ball (CNLR1020) Antirotation Linkage Ball (CNE515) *Hint: Undo the cap screws and linkage balls to the assembled parts. Apply CA on metal to plastic assembly. Apply blue thread lock on metal to metal assem- bly. Do not over tighten when screwing the attached assembly to its subassembly. Swashplate (CNE515) Swashplate and Washout Assembly 6. Assembly Instructions CA Main Shaft (CNE508) Flybar outer �
Century Swift Carbon 550, 1) Align the mounting posts from the front transmission gearbox with the mounting posts at the rear of the main frame. The horizontal n on the tail boom facing should face up so the rudder pushrod and tail boom support struts hang below the tail boom. 2) Using the hardware provided attach the tail section to the frame section. Do not fully tighten the screws till the following step. 1) Align the transmission gear mesh before fully tightening the screws holding the frame and tail sections. Good alig
(1) The Swift Carbon 550 does not come with main rotor blades. Please refer to the instructions included with your blades (must be purchased separately and are not included with the Swift Carbon 550 kit). (2) Use the 2 M4x30 blade bolts and M4 locknuts to secure the blades to the blade grips on the main rotor head. Main rotor blades should have their leading edge turning clockwise. IMPORTANT
Flybar Paddle Cover Flybar Paddle Flybar Wipe the paddles with 70% Isopropyl alcohol making sure that it is free from oil. Use the ybar paddle cover found on the decal sheet. Wrap around the ybar paddle. Hint: Cover the bottom end of the ybar paddle and adhere the ex- cess covering material to the trailing edge of the ybar p
Century Swift Carbon 550, Uppper Bearing Block Assembly 6. Assembly Instructions CF Main Shaft Support (CNE577) A-Arm Bearing (CNE582) Aluminum Spacer 3.5mm (CNE586) Cap Screws M3x12 (CNM3x12CS) Aluminum Spacer 3.5mm (CNE586) Upper Bearing Block, Bearing (CNBB1019) Upper Bearing Block (CNE593) Cap Screw M3x8 (CNM3x8CS) M3 Hex Lock Nut (CNM3LOCK) 1. Lay down part; CF Main Shaft Support over the holes to ensure correct orientation. 2. Be sure to install the plate on the op- posite side to the bellcrank 3. The hole for the A-arm bearing is tight and may require sanding in order for the bearing to t.
Century Swift Carbon 550, 14. Replacement Parts CNBB364 Bell Mixer Bearing (4) CNBB1030 Rotor Hub Bearing (2) CNBB364 CCPM Bell Crank Bearing (4) CNBB0730 Seesaw Bearing (2) CNBB0384 Tail Blade Grip Bearings (4) CNBB1350 Tail Gear Box Bearing (2) CNBB614T2 Main Blade Grip Thrust Bearing (2) CNBB814 Main Blade Grip Radial Bearings (2) CNBB1019 Upper/Lower Bearing Block Bearing (1) CNBB4102 Transmission Gear Bearing (2) CNBB610 Tail Pitch Slider Bearing (2) CNBB364 Tail Pitch Lever Bearing (4) CNE587 Motor Mount Spacer (2) CNE588 Bell Crank Spacer (2) CNE590 Transmission Box Spacer (2) CNE591 Driven Tail Hub CNE593 Upper Bearing Block CNE592 Tail Hu
Century Swift Carbon 550, 3. Required Items for Operation Part#CN2015 Hardened Tip Hex Screw Driver Set Part#CN2026 Pitch Gauge with Paddle Gauge Part#CN2034A 15 0 Curve Tip Ball link Pliers Part#CN2052 Main Blade Balancer Part#CN2055 Ball Link Sizing Tool Part#CN2070 Universal Flybar Lock Part#CN2219 Ball Link Easy Driver Part#CN2255 Control Rod Gauge Part#CNWI26555 5.5mm Nut Driver Part#CNWI26570 7.0mm Nut Driver Hobby scissors #CN2262 Hardware Description and Identication: M3x6 = 3x6mm and can refer to screws or ball bearings. M3x6 Phillips Machine Screw M - metric 3
Century Swift Carbon 550, Use this table as a guide, your setup and ight conditions will make these results uctuate. For ultimate performance with head speeds reaching close to 2000rpm, Century recommends the use of high quality ight packs with at least 20C constant discharge rate. 4S (14.8V) 5S (18.5V) 6S (22.2V) Motors Pinion Headspeed Pinion Headspeed Pinion Headspeed Century 550 PLUS 9T 1730 9T 2160 N/A (CNE271) 10T 1930 RPM/V: 1470 Century 600 PLUS 13T 1890 10T 1820 9T 1990 (CNE273) 14T 2040 11T 2000 RPM/V: 1110 NEU 1907 1.5Y 14T 1700 13T 1940 N/A
Century Swift Carbon 550, 2. Included in your kit is a small piece of sand paper. You may have to sand down the edges of your radio tray and gyro plate in order for them to t perfectly. When sanding, remove small amounts of material and test t the parts. You want the parts to t snuggly in place. *WARNING: Before sanding, make sur e you and your model are in a well venti- lated area, or outside. When sanding car- bon, you must wear a dust mask as inhaling the dust particles can be harmful to your health.* Lower Bearing Block Assembly 6. Assembly Instructions 1. Push the bearing (CNBB1019) into t
Lionel NW2 Toy Owner's manual
NW2 |
Kyosho N10751 Minium Toy Instruction manual
N10751 Minium |
Century Radikal G20 Toy Instruction manual
Radikal G20 |
LeapFrog Touch Magic Rockin' Guitar Toy Parent manual & instructions
Touch Magic Rockin' Guitar |
Extreme Flight MXS-EXP Toy Assembly manual
MXS-EXP |
Extreme Flight RC YAK-54 AFR Toy Instruction manual
YAK-54 AFR |
Ares V-Hawk X4 Toy Owner's manual & technical information
V-Hawk X4 |
marklin Gepäckwagens Toy Operation & user’s manual
Gepäckwagens |
# | Manufacturer | Model | Document Type | File | Updated | Pages | Size |
---|---|---|---|---|---|---|---|
1 | Britax | AHR Air Cushion 7200 A 2010 | User manual manual | britax/ahr-air-cushion-7200-a-2010-685.pdf | 27 Oct 2023 | 33 | |
2 | Acer | PD100 | Quick start manual | acer/pd100-EIZ.pdf | 30 Jan 2024 | 4 | 4.08 Mb |
3 | Senco | SCN60 | Parts reference manual | senco/scn60-K8Q.pdf | 07 Feb 2023 | 4 | 0.79 Mb |
4 | Sony | VAIO PCV-RZ10CE | Important information | sony/vaio-pcv-rz10ce-A36.pdf | 26 Aug 2022 | 1 | 0.04 Mb |
5 | Marantz | MA700 | Operation & user’s manual | marantz/ma700-PQ3.pdf | 29 Jan 2024 | 13 | |
6 | Aiwa | CSD-TD39 | Operating instructions manual | aiwa/csd-td39-QE1.pdf | 21 Feb 2024 | 12 | 0.31 Mb |
Viessmann
BedienungssanleitungOperation Manual4750H0 Signalbrücke mit zwei Einfahrsignalen und Multiplex-Technologieüber zwei GleiseH0 Signal bridge with two signals with muliplex technologyover two tracks1. Wichtige Hinweise ...................................... 22. Einführung / Eigenschaften ........................ 33. Montage ......................... …
4750(8 pages) |
Radio Shack
Baby Mantis60-2800Thank you for purchasing the RadioShack RC Mantis. Drive your mantis forward and backward - you’ll see its tentacles light, its eyes move, its head turn side to side, and all six legs hit the ground running! Your man-tis comes in two frequencies, 27 MHz and 49 MHz, so you can play with your friends. Check your box to see what frequency yo …
60-2800(1 pages) |
MGA Entertainment
SUPER SURPRISE0620-0-E/INTPrinted in ChinaPlease keep this manual as it contains important information.MGA Entertainment, Inc.9220 Winnetka Ave. Chatsworth, CA 91311 U.S.A.(800) 222-4685MGA Entertainment UK Ltd.50 Presley Way, Crownhill, Milton Keynes, MK8 0ES, Bucks, UK+ 0800 521 558MGA Entertainment (Netherlands) B.V.Baronie 68-70, 2404XG Alphen a/d Rijn, …
L.O.L. SURPRISE! O.M.G. OUTRAGEOUS MILLENNIAL GIRLS REMIX Super Surprise(2 pages) |
Reely Sky
Elektro-Flugmodell „Fournier RF-4D“ ARF Electric Flight Model „Fournier RF-4D“ ARF Modèle réduit d’avion électrique« Fournier RF-4D » ARF Elektrisch modelvliegtuig „Fournier RF-4D“ ARFBest.-Nr. / Item No. / N° de commande / Bestelnr.: 27 51 04 Bedienungsanleitung Seite 2 - 24 Operating Instructions Page 25 - 47 Notic …
Fournier RF-4D(96 pages) |
REVELL
* REPEAT SEVERAL TIMES* A REPETER PLUSIEURS FOIS* CEMENT TOGETHER* A COLLER* REMOVE AND THROW AWAY* A RETIRER ET JETER* DO NOT CEMENT* NE PAS COLLER* DECAL * DECAL COMANIE* ASSEMBLY CAUTION*ATTENTION D ASSEMBLEE* OPTIONAL PARTS* PIECES EN OPTION* REPEAT PROCEDURE* R E P E T E Z L E P R O C E D E `` ` ` ` `DECAL PLACEMENT25AluminumDark …
KIT 5716(16 pages) |
Topmodel
Order N° 099005ATTENTION !Ce modèle à construire n’est pas un jouet, ilne convient pas aux enfants de moins de 14 ans.Une mauvaise utilisation de ce matériel peutprovoquer des dommages matériels ou corporels. Vous êtes pleinement responsablelorsque vous utilisez votre modèle. Volez à une distance de sécurité des zones habitées.Soyez sûr que per …
XPower Krasivo 2(26 pages) |
Silver King Merchandiser SKCTMDITechnical manual and replacement parts list for Silver King SKCTMDI Merchandiser SKCTMDI, 12 |
I-Rad Two-Way Radio 420855102108Two-Way Radio #D7S667 420855102108, 15 |
Palsonic Telephone VCR6200HSVCR6200HS Operation & user’s manual - 36Q47S VCR6200HS, 32 |
Northern Lights Fitness Equipment AVALANCHE4 MULTI-GYMNorthern Lights Product Guide: AVALANCHE4 MULTI-GYM PDF Assembly instructions manual - 7983RD AVALANCHE4 MULTI-GYM, 13 |
IVI Network Card Drive#B534Q3 Drive: IVI Network Card Owner Documentation Drive, 114 |
Beko Refrigerator RBI 2300 HCAPDF Guide (@8CCWX9), Beko RBI 2300 HCA Refrigerator (Wed 01.2024) RBI 2300 HCA, 48 |
Sony Laptop VAIO PCG-505FSony Laptop VAIO PCG-505F Operation & user’s manual VAIO PCG-505F, 118 |
MULTIQUIP Heat Pump P200DLSTMULTIQUIP P200DLST User Manual (Operation manual), @ZR4452 P200DLST, 58 |
Wintec Bicycle Accessories Ego WBC 300 PlusWintec Ego WBC 300 Plus Guide (Doc Type: Bicycle Accessories Instruction manual) Ego WBC 300 Plus, 4 |
Avaya Telephone 6424D+MAvaya Product Guide: 6424D+M PDF Operation & user’s manual - L86G11 6424D+M, 143 |
Philips Stereo System FWM377/05Philips Product Guide: FWM377/05 PDF Quick start manual - P9O855 FWM377/05, 4 |
Ariston Refrigerator MBL 300 FPDF Guide (@Z3ZZTL), Ariston MBL 300 F Refrigerator (Thursday 02-11-2023) MBL 300 F, 16 |