Cisco CompactFlash Adapter Installation Manual

Text of Cisco CompactFlash Adapter User Guide:

• Cisco CompactFlash Adapter, Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note Product Numbers: WS-CF-UPG=, CF-ADAPTER=, WS-CF-UPG-1GB= This publication describes how to replace the switch processor (SP) bootflash memory module (DIMM) with CompactFlash on the Supervisor Engine 720. The WS-CF-UPG= and the CF-ADAPTER= support a 512 MB CompactFlash card; the WS-CF-UPG-1GB= supports a 1 GB CompactFlash card. Contents This publication consists of these sections: • Safety Overview, page 2 • Installing the SP Bootflash Memory Upgrade Kit, page 8 • Removing and

• Cisco CompactFlash Adapter, 21 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Figure 10 Clearing the EMI Gasket in a Vertical Slot Chassis c. Using the thumb and forefinger of each hand, grasp the two ejector levers and exert a slight pressure to the left, deflecting it approximately 0.040 inches (1 mm) creating a small gap between the supervisor engine’s EMI gasket and the module adjacent to it. (See Figure 10.) Note Do not exert too much pressure on the ejector levers because they will bend and be damaged. d. While pressing down on the ejector levers, simultaneously close the lever

• Cisco CompactFlash Adapter, 11 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Step 6 Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the following two sets of steps: Horizontal slots a. Place your thumbs on the left and right ejector levers, and simultaneously rotate the levers outward to unseat the supervisor engine from the backplane connector. (See Figure 2.) b. Grasp the front edge of the supervisor engine, and slide the supervisor engine partially out of the slot. Place your other hand under the supervisor engine to support the weight of the m

• Cisco CompactFlash Adapter, 23 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Removing and Installing the CompactFlash in the CompactFlash Adapter Figure 11 Removing the CompactFlash from the Adapter To install the CompactFlash in the adapter, follow these steps: Step 1 Remove the replacement CompactFlash from its packaging. Step 2 Grasp the empty adapter and the CompactFlash, and position the CompactFlash in front of the adapter as shown in Figure 12, View 1. Align the slots in the CompactFlash with the rails in the adapter. Step 3 Slide the CompactFlash into the adapter until the CompactFlash is firmly seated in the adapter connector. (See Figure 12, Views

• Cisco CompactFlash Adapter, 10 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Removing the Supervisor Engine 720 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 The following tools are required to perform the bootflash upgrade kit installation: • 3/16-inch flat-blade screwdriver for the captive installation screws on the supervisor engine • Antistatic mat or foam pad to support and protect the removed supervisor engine • Your own ESD-prevention equipment or the disposable grounding wrist strap included with all upgrade kits, field

• Cisco CompactFlash Adapter, 26 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Module Handling Guidelines Figure 13 Attaching the ESD Wrist Strap Clip to the System Ground Lug Screw Module Handling Guidelines Follow these guidelines when handling modules: • Handle carriers by available handles or edges only; avoid touching the printed circuit boards or connectors. • Place a removed component board-side-up on an antistatic surface or in a static shielding container. If you plan to return the component to the factory, immediately place it in a static shielding container. • Never att

• Cisco CompactFlash Adapter, 22 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Removing and Installing the CompactFlash in the CompactFlash Adapter Note Depending on how your system bootstring is configured, your system might stay in ROMMON. To boot the system from the CF adapter, enter the boot bootdisk: command. Once you install the CF adapter, you must define the Cisco IOS bootstring as boot system flash sup-bootdisk:[image name] With SP ROMMON Release 8.4(2), the bootstring has to be defined as su

• 30 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Safety Warning Translations ¡Advertencia! Las placas frontales y los paneles de relleno cumplen tres funciones importantes: evitan la exposición a niveles peligrosos de voltaje y corriente dentro del chasis; reducen la interferencia electromagnética (EMI) que podría pert

• Cisco CompactFlash Adapter, 16 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Reinstalling the Supervisor Engine 720 Caution During this procedure, wear grounding wrist straps and handle modules by the carrier edges only to avoid ESD damage to the card. To reinstall the Supervisor Engine 720 in the chassis, follow these steps: Step 1 Attach an ESD grounding strap to your wrist and to ground. (If you are unsure about the correct way to attach an ESD grounding strap, see the “Attaching Your ESD Grounding Strap” section on

• Cisco CompactFlash Adapter, 32 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Safety Warning Translations Statement 1034—Backplane Voltage Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Waarschuwing Er is gevaarlijke spanning of energie aanwezig op de achterplaat wanneer het systeem bediend wordt. Wees voorzichtig bij het onderhoud. Varoitus Kun laite on toiminnassa, taustalevyyn muodostuu vaarallista jännitettä. Ole varovainen huoltaessasi laitetta. Attention Lorsque le système est en fonctionnement, des tensions électriques circulent sur le fond de p

• Cisco CompactFlash Adapter, 14 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Figure 4 SP and RP DIMM Locations on the Supervisor Engine 720 Step 2 Release the SP DIMM from the socket by simultaneously releasing the two locking spring clip tabs on either side of the DIMM socket. (See Figure 5, left view.) The DIMM will flip up in the socket. (See Figure 5, right view.) Step 3 Hold the DIMM by its edges and carefully remove it from the DIMM socket. Figure 5 Removing the DIMM Step 4 Immediately place the DIMM in an antistatic bag. 144402 RP Bootflash SP Bootflash 144403

• 13 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Figure 3 Removing the Module from the Chassis (Horizontal Chassis Shown) Installing the CompactFlash Adapter To install the CompactFlash adapter, follow these steps: Step 1 Locate the SP BOOTFLASH DIMM socket on the Supervisor Engine 720. (See Fi

• Cisco CompactFlash Adapter, 24 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Attaching Your ESD Grounding Strap Figure 12 Installing a CompactFlash in the Adapter Attaching Your ESD Grounding Strap Electrostatic discharge (ESD) damage, which can occur when modules or other FRUs are improperly handled, results in intermittent or complete failures. Modules consist of printed circuit boards that are fixed in metal carriers. Electromagnetic interference (EMI) shielding and connectors are integral components of the carrier. Although the metal carrier helps to protect the board from ESD, always use an ESD g

• Cisco CompactFlash Adapter, 15 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Step 5 Open the antistatic bag containing the SP CompactFlash adapter. Note The SP CompactFlash adapter has a label attached to the CompactFlash identifying it as the SP CompactFlash adapter. Step 6 Carefully align the CompactFlash adapter edge connector with the DIMM socket. Slide the CompactFlash adapter edge connector at an angle into the socket. (See Figure 6.) Note Make sure that the CompactFlash adapter edge connector is fully inserted into the DIM

• Cisco CompactFlash Adapter, 28 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Safety Warning Translations Aviso Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar manutenção a este equipamento. Advarsel Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr.

• 34 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Obtaining Documentation and Submitting a Service Request This document is to be used in conjunction with the Cisco IOS Software Configuration Guide. CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Wa

• Cisco CompactFlash Adapter, 18 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Installing the SP Bootflash Memory Upgrade Kit Step 4 Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the following two sets of steps: Horizontal slots a. Position the supervisor engine in the slot. (See Figure 7.) Make sure that you align the sides of the module carrier with the slot guides on each side of the slot. b. Carefully slide the supervisor engine into the slot until the EMI gasket along the top edge of the module makes contact with the module in the slot above it and both ejector levers

• Cisco CompactFlash Adapter, 5 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Safety Overview Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

• 4 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Safety Overview Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circui

• Cisco CompactFlash Adapter, 27 Cisco CompactFlash Adapter for Bootflash Upgrade Installation Note 78-17277-05 Safety Warning Translations Safety Warning Translations This section repeats in multiple languages the basic warnings that appear in this publication. Statement 1030—Equipment Installation Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel. Varoitus Tämän laitteen saa asentaa

Related Products and Documents (Adapter):

Comparable Devices:

Similar Resources:

• NETGEAR N150 (2 pages) Quick StartPackage ContentsFront and Back PanelsN150 and N300 Wireless RoutersRouter (product appearance varies by model)Ethernet cable (only available for some models)Power adapter (varies by region)Power LEDInternet LED WiFi LEDEthernet LEDs 1–4Ethernet ports 1–4Internet portPower connectorWPS/Reset button1. Prepare your modem.Unplug your modem’s p …

• ATTO Technology ATTO Celerity FC-44ES (2 pages) Product Features Technical Specification For More Information: www.ATTOTech.com or to Purchase: www.ATTOStore.com (716) 691-1999 Celerity FC-44ES Host Adapter Quad-channel 4-Gigabit Fibre Channel Host Adapter Featuring ADS™ Technology The fastest storage technology just got better! The Celerity FC-44ES leverages two next-generation storage techn …

• ORION TELESCOPES & BINOCULARS 5339 (3 pages) Orion® Variable Universal Camera Adapter, 1.25"#5339INSTRUCTION MANUALProviding Exceptional Consumer Optical Products Since 1975IN 008 Rev. C 06/14Customer Support:www.OrionTelescopes.com/contactusCorporate Offices:89 Hangar Way, Watsonville CA 95076 - USACopyright © 2014 Orion Telescopes & Binoculars All Rights Reserved. No part of this product i …

• D-Link DUB-E100 (8 pages) - 1 - This Installation Guide includes instructions for: § Windows XP § Windows 2000 § Windows Me § Windows 98/98se Review Package Contents: Make sure that the package contains the following items. If any items are missing, please contact your reseller. § D-Link DUB-E100 § USB 2.0 Certified A to B Cable § Drivers on CD-ROM § This Installat …

• Patton electronics 464RC (5 pages) USERMANUALMODEL 464RC & 466RCRack-Mounted G.703 Coax toTwisted PairAdapters (BALUNs) SALES OFFICE(301) 975-1000TECHNICAL SUPPORT(301) 975-1007http://www.patton.comPart # 07M464RC-ADoc. # 019151URevised 12/06/00An ISO-9001Certified Company …

• Black Box Multi-Function Line Driver (2 pages) © 2010. All rights reserved. Black Box Corporation.FREE 24-hour Tech Support: 724-746-5500blackbox.com 1 of 212/14/2010 #13727Multi-Function Line DriverUse this line driver in just about any RS-232 UTP or STP application. …

Comments, Questions and Opinions: